hitron CHITA3.1 CHITA-RES Cable Modem Router User Guide

hitron CHITA3.1 CHITA-RES Cable Modem Router User Guide

• Connect to the network
• Set up your wireless network

Check the box contents

Look in the box and make sure you have the following:

• **CHITA3.1

**

• POWER ADAPTER
  
  

• **ETHERNET CABLE

**

• **QUICK START GUIDE

**

Connect the cable port

Connect the device’s CABLE connector to a cable outlet in your home.

Connect the power adapter

Connect the included power adapter from the POWER port to a wall outlet.

Access LAN for initial configuration

To complete initial setup, you can access CHITA3.1 using a laptop connected by a Ethernet cable or any mobile device with the default Wi-Fi network name found on the back label of your new CHITA3.1.

Ethernet Method

Wi-Fi Method

Wireless Devices (Optional)

Connect your wireless devices with the correct SSID and Passphrase chosen in label.

To connect a wireless device with the Wi-Fi Protected Setup button (WPS), You need to first access the GUI with the user “cusadmin” and password as “password”, enter the Wireless page to enable WPS for each band seperately and then save the changes. Press the WPS button on the CHITA3.1 and on the device you wish to connect within 2 minutes of each other while they are in the coverage area.

Connect a Telephone Device (Optional)

Connect any LINE port to a telephone This is required only if you have ordered telephone service.

Setup complete

Congratulations! You have successfully set up your CHITA3.1. If you have any problems, see the section below for help identifying the problem.

IP addresses
If your CHITA3.1 is successfully connected to the network (see LED display) but you cannot access the Internet from a connected device, your device’s IP address may be set up incorrectly

In your device’s control panel, ensure that the device is configured to receive an IP address automatically (recommended) or that it has a static IP address in the following range:
192.168.0.2~192.168.0.253. For more information, consult your operating system’s documentation.

LED display

POWER| Green-Steady
Off| Modem is running with AC power
Not powered.
---|---|---
DS| Green-Blinking
Green-Steady
Blue-Steady
Cyan-Steady
Off| The modem is searching for the downstream frequency
Downstream frequency is locked. (1 channel only)
Downstream frequency is locked. (channel bonding)
DOCSIS 3.1 OFDM
Not scanning
US| Green-Blinking
Green-Steady Verde-Estable
Blue-Steady
Cyan-Steady
Off| The modem is searching for the upstream frequency
Upstream frequency is locked. (1 channel only
Upstream frequency is locked. (channel bonding)
DOCSIS 3.1
Not scanning
STATUS| Green-Blinking
Green-Steady
Off| Registration is in progress with cable company’s head-end.
Modem is operational.
Modem is offline
ETHERNET| Green-Blinking
Off| Ethernet is activated
Ethernet is disabled
2.4G| Green-Blinking
Green-Steady
Off| The 2.4GHz wireless network is enabled, and data is being transmitted or received.
The 2.4GHz wireless network is enabled, and no data is being transmitted or received.
Not powered
5G| Green-Blinkin
Green-Steady
Off| The 5GHz wireless network is enabled, and data is being transmitted or received
The 5GHz wireless network is enabled, and no data is being transmitted or received.
Not powered.
TEL 1| Green-Blinking
Green-Steady
Off| The line is in use
The line is activated.
The line is not activated
TEL 2| Green-Blinking
Green-Steady
Off| The line is in use
The line is activated.
The line is not activated

Safety warnings

WARNING
Risk of electrical shock. Do not expose the device to water or moisture.
The device is a high-performance communications device designed for home and office environments.
Do not use the device outdoors.
Keep the device in an environment between 0°C ~ 40°C (32°F ~104°F).
To avoid overheating, do NOT place any object on top of the device.
Do not restrict the flow of air around the device.

DISCLAIMER
The manufacturer assumes no liabilities with respect to the contents of this document.
The manufacturer also reserves the right to revise this document or update the content thereof without any obligation to notify any person of such revisions or amendments.
Specifications subject to change without notice.

CAUTION
The cable distribution system should be grounded (earthed) in a accordance with ANS/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device is restricted for indoor use.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 41cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>