hitron CODA-4589 Cable Modem Router User Guide

June 8, 2024
Hitron

hitron CODA-4589 Cable Modem Router User Guide

Check the box contents

  1. Look in the box and make sure you have the following:
    Regardez dans la boîte et assurez-vous d’avoir les items suivants

  2. Connect the cable port/
    Connect the device’s CABLE connector to a cable outlet in your home

  3. Connect the power adapter
    Connect the included power adapter from the POWER port to a wall outlet

  4. Access LAN for initial configuration
    To complete initial setup, your CODA will launch Easy Connect user interface on the first connected device. You can access it using a laptop connected by a Ethernet cable or any mobile device with the default Wi-Fi network name found on the back label of your new CODA.

  5. User configuration
    For initial setup, click “LET’S GO” to test your connection and enter your preferred SSID and Passphrase. The Wi-Fi Passphrase will also act as your password with the username “cusadmin” the next time you visit 192.168.0.1. Make sure to complete the Easy Connect walkthrough so it does not come back. If the CODA receives a factory reset, the Easy Connect interface will appear again

  6. Wireless Devices (Optional)
    Connect your wireless devices with the correct SSID and Passphrase chosen in Step 5.
    Connectez vos appareils sans-fil avec votre SSID et « Passphrase » choisis à l’étape 5.

Connect a Telephone Device (Optional)/

Connect any LINE port to a telephone. This is required only if you have ordered telephone service

Setup complete/

Congratulations! You have successfully set up your CODA. If you have any problems, see the section below for help identifying the problem.
Félicitations! Vous avez configuré votre CODA avec succès. Si vous rencontrez un problème, consultez la section ci-dessous pour vous aider à en déterminer la nature.

IP addresses/ Adresses IP
If your CODA is successfully connected to the network (see LED display) but you cannot access the Internet from a connected device, your device’s IP address may be set up incorrectly.
Si votre CODA est correctement connecté au réseau (voir la section Affichage DEL), mais que votre appareil n’a pas accès à Internet, il se peut que l’adresse IP de ce dernier ne soit pas configurée correctement.
In your device’s control panel, ensure that the device is configured to receive an IP address automatically (recommended) or that it has a static IP address in the following range:
192.168.100.10~192.168.100.254. For more information, consult your operating system’s documentation.
Dans le panneau de configuration de votre appareil, assurez-vous que celui-ci soit configuré pour recevoir une adresse IP automatiquement (recommandé) ou qu’il dispose d’une
adresse IP statique dans la plage 192.168.100.10~192.168.100.254. Pour plus de renseignements, consultez la documentation portant sur votre système d’exploitation.

LED display

Safety warnings/

WARNING/ ATTENTION
Risk of electrical shock. Do not expose the device to water or moisture.
The device is a high-performance communications device designed for home and office environments. Do not use the device outdoors.
Keep the device in an environment between 0°C ~ 40°C (32°F ~104°F). To avoid overheating, do NOT place any object on top of the device.
Do not restrict the flow of air around the device. The manufacturer assumes no liabilities for damage caused by any improper use of the device.

FCC STATEMENTS

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
This device is restricted for indoor use

IMPORTANT NOTE:

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
The cable distribution system should be grounded (earthed) in accordance with ANSI /
NFPA 70, National Electrical Code (NEC), in particular Section 820.93, Grounding of
Outer Conductive Shield of a Coaxial Cable. le système de distribution par câble doit être mis à la terre ( la terre) conformément à la
norme ANSI / NFPA 70 , National Electrical Code ( NEC ), en particulier l’article 820.93 , la terre du blindage conducteur extérieur d’un câble coaxial
environment. This equipment should be installed and operated with minimum distance 47cm between the radiator & your body

Industry Canada statement

This device complies with ISED’s licence-exempt RSSs. Operation is subject to th following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals