hitron CGNV5-U DOCSIS 3.0 Cable Modem User Guide
- October 27, 2023
- Hitron
Table of Contents
hitron CGNV5-U DOCSIS 3.0 Cable Modem
- Connect to the Internet
- Connect phone
- Configure wireless network
Check the contents of the packaging
- Look into the box and make sure you have the followings:
Connect the cable port
- Connect the coaxial cable from the cable outlet to the CABLE port.
Turn on the power
- Connect the power adapter to the POWER port.
Connect the phone to the voice port
- Use the telephone cable to connect your telephone to the TELEPHONE port and wait for dial tone before using.
Connect your computer to the device
- Use the Ethernet cable that came with the device to connect your computer to one of the LAN ports.
User configurations (optional)
-
Your device has a configuration interface that allows you to completely control the behavior of the device. In a web browser, enter the IP of the device in the address bar and make sure your PC is on the same subnet as the device. On the screen that appears, enter username and password.
-
User name:
XXXXX -
Password:
XXXXXXXXX -
Web address:
HTTP//XXXXXXXXX -
Device IP:
Mood Router: 192.168.0.1 Mode Bridge: 192.168.100.1
-
Connect your computer to wireless network
-
Connect the wireless devices with SSID and correct password. If you have not changed them, the default values are indicated on the sticker at the bottom of the device.
Connect your wireless devices by WPS. Access the configuration interface (see step 6), go to the Wireless page to enable WPS and set AES encryption mode, then press Save changes.
Press this button to start the procedure for setting up WPS (PBC). Press PBC button of your wireless clients within coverage area in two minutes to allow joining the wireless network.
Installation complete
Congratulations!
You have successfully setup your CGNV5-U. If you have any problem, see the
next section for help to identify the cause.
IP addresses
If the CGNV5-U is correctly connected to the network (see LED Display) but
connected computer cannot access to the Internet, the IP address of your
computer may not be configured correctly. In the network configuration of the
equipment, make sure it is configured to receive IP address automatically
(recommended) or it has a static IP address in the range
192.168.0.2-192.168.0.253.
For more information, please consult your system operator for help.
LED lights display
Safety Warnings
WARNING
Risk of electrical shock. Do not expose the device to water or moisture.
The device is a high-performance communications device designed for home and
office environments. Do not use the device outdoors.
Keep the device in an environment between 0°C ~ 40°C (32°F ~104°F).
To avoid overheating, do NOT place any object on top of the device.
Do not restrict the flow of air around the device.
The manufacturer assumes no liabilities for damage caused by any improper use
of the device.
DISCLAIMER
The manufacturer assumes no liabilities with respect to the contents of this
document. The manufacturer also reserves the right to revise this document or
update the content thereof without any obligation to notify any person of such
re visions or amendments. Specifications subject to change without notice.
CAUTION
The cable distribution system should be grounded (earthed) in a accordance
with ANS/NFPA 70, the National Electrical Code (NEC), in particular Section
820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.
COPYRIGHT © 2019 HITRON TECHNOLOGIES, INC.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device is restricted for indoor use.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>