Cloud CS-C4HW In-Ceiling Loudspeakers Installation Guide

Cloud CS-C4HW In-Ceiling Loudspeakers

Product Information

The CS-C Series In-Ceiling Loudspeakers are a range of high-quality speakers designed for installation in ceilings. The series includes the following models:

• CS-C6: 6.5 IN-CEILING LOUDSPEAKER
• CS-C8: 8 IN-CEILING LOUDSPEAKER
• CS-C5: 5 IN-CEILING LOUDSPEAKER
• CS-C4: 4 IN-CEILING LOUDSPEAKER
• CS-CSUB8: 8 IN-CEILING SUBWOOFER
• CS-C3: 3 IN-CEILING LOUDSPEAKER

The speakers are designed to provide clear and powerful audio in a variety of settings. They feature tap settings that allow for easy customization to suit different systems and environments. The speakers also come with an installation guide for proper setup.

Product Usage Instructions

1. Remove the speaker from the box.
2. Mark and cut a hole in the ceiling or ceiling tile using the included hole template. The dimensions for the hole vary depending on the model:
   • CS-C3: 140 mm (5.50)
   • CS-C4: 177 mm (6.88)
   • All other models: 271 mm (10.67)
3. Locate the euroblock in the accessory bag and connect the signal wire. Insert the euroblock into the rear of the back can.
4. Attach the safety restraint to the rear of the back can and close and secure the cover plate.
5. Remove the grille and set the tap switch to the proper setting. Attach the grille leash to the baffle by placing the large end of the clip over the snap fit post and sliding the clip until the small end snaps into place. The tap switch is preset to the highest 100 V position.
6. If installing on a ceiling tile, place the tile bridge on the back of the ceiling tile. Align the holes and insert the speaker into the hole. Tighten the dog ears, but do not overtighten. (Tile bridge not available for C4.)
7. If installing on drywall, insert the speaker into the ceiling opening and tighten the dog ear clamps, but do not over tighten.
8. Check the tap setting and replace the grille.
9. Remove the logo tab if desired.

Note: For daisy-chaining multiple speakers, use the LINK output to run to the next speaker. Make sure to follow all safety precautions and refer to the installation guide for further details.

• CAUTION – Installation
  Speaker must be installed by qualified speaker technician.

• CAUTION – Servicing
  The unit contains no user-serviceable parts. Refer servicing to qualified personnel. Do not perform servicing unless you are qualified to do so.

• CAUTION – Tap Switch
  Before use check and set tap switch under grille to proper setting for your system.

EXPLODED VIEW

TAP SETTINGS

Tap| CS-CSUB8| CS-C8| CS-C6| CS-C5| **CS-C4*| CS-C3
---|---|---|---|---|---|---
 | 100 V| 70 V| 25 V| 100 V| 70 V| 25 V| 100 V| 70 V| 25 V| 100 V| 70 V| 25 V| 100 V| 70 V| 25 V| 100 V| 70 V| 25 V
1| 4 ohm| 16 ohm| 16 ohm| 16 ohm| 16 ohm| 16 ohm
2| X| 100W| 13W| X| 64W| 8W| X| 32W| 4W| X| 20W| 2.5W| X| 20 W| 2.5 W| X| 16W| 2W
3| 100W| 50W| 7W| 64W| 32W| 4W| 32W| 16W| 2W| 20W| 10W| 1.3W| 20 W| 10 W| 1.3 W| 16W| 8W| 1W
4| 50W| 25W| 3W| 32W| 16W| 2W| 16W| 8W| 1W| 10W| 5W| 0.6W| 10 W| 5 W| 0.7 W| 8W| 4W| 0.5W
5| 25W| 13W| 1.5W| 16W| 8W| 1W| 8W| 4W| 0.5W| 5W| 2.5W| 0.3W| 5 W| 2.5 W| 0.4 W| 4W| 2W| 0.3W
6**| 13W| 6W| 0.8W| 8W| 4W| 0.5W| 4W| 2W| 0.3W| 2.5W| 1.3W| 0.2W| 2.5 W| 1.3 W| 0.2 W| 2W| 1W| 0.2W

INSTALLATION

• Step 1
  Remove speaker from box.

• Step 2
  Mark and cut hole in ceiling or ceiling tile. Use included hole template.

• Step 3
  Locate euroblock in accessory bag and connect signal wire. For daisy-chaining use “LINK” output to run to next speaker.

• Step 4
  Remove grille and set tap switch to proper setting and attach grille leash to baffle by placing the large end of the clip over the snap fit post (1) then sliding the clip until small end snaps into place. Tap switch is preset to highest 100 V position.

• Step 5 (Ceiling Tile Only)
  Place tile bridge on back of ceiling tile. Align holes and insert speaker in hole. Tighten dog ears. Do not overtighten. (Tile bridge not available for C4.)

• Step 6
  Insert euroblock into rear of back can. Attach safety restraint to rear of back can. Close and secure cover plate.

  • (CS-C3 and CS-C4 only)
    Insert euroblock into rear of back can. Attach safety restraint to side of back can. Close and secure cover plate. Note that on model CS-C4H only, there is an additional rubber seal with a pre-cut “X” to allow cable access.

• Step 7 (Drywall)
  Insert speaker into ceiling opening and tighten dog ear clamps, do not over tighten.

  • (Ceiling Tile Only)
    Insert euroblock into rear of back can. Attach safety restraint to rear of back can. Close and secure cover plate, reattach grille to speaker. Insert speaker, tile and tile bridge into ceiling.

• Step 8
  Check tap setting and replace grille.

• Step 9
  Remove logo tab if desired.

NOTE: ALTERNATIVE GRILLES
All CS-C models are supplied with a circular grille as shown in the above diagrams.
Optional square grilles are available for all models except CS-C4: CS- 8SQGRILLW (white) and CS-8SQGRILLB (black) are compatible with Models CS-C5, CS-C6, CS-C8 and CS-C8SUB/CS-C3SQGRILLW (white) and CS-C3SQGRILLB (black) are compatible with Models CS-3C Optional hexagonal grilles are available for CS- 3C only: CS-C3HEXGRILLW (white) and CS-C3HEXGRILLB (black)

All alternative grilles feature the same system of magnetic attachment to the speaker as the standard circular grilles, and therefore there is no difference in installation procedure.

www.cloud.co.uk
www.cloudusa.pro

References

• Home | Cloud
• cloudusa.pro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>