CLAS OH 0931 Dual Control Hydraulic Press User Manual
- June 13, 2024
- CLAS
Table of Contents
- SPECIFICATIONS
- SAFETY INSTRUCTIONS
- TECHNICAL DATA
- TECHNICAL DESCRIPTION
- BEFORE USING THE PRESS
- USE AND OPERATION
- OPERATION DESCRIPTION
- SADDLE AND PIN SETS OPERATION
- BLOCKERS OPERATION
- MOVEABLE CYLINDER OPERATION
- WORKING TABLE OPERATION
- MAINTENANCE INSTRUCTION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CLAS OH 0931 Dual Control Hydraulic Press User Manual
WARNING
Before using: Please be sure to read and understand all safety rules and
instructions in this manual before operating the heating inductor. Pay
particular attention to the safety rules. Failure to follow all instructions
listed below may result in electric shock, fire, and/or serious personal
injury.
Before returning this product for any reason (installation problem, instructions for use, breakdown, manufacturing problem…), please contact us.
Contact : You can reach us by mail sav@clas.com or by phone +33(0)4 79 72 69 18 or go directly to our website clas.com If you have changed your mind regarding your purchase, please return this product before you attempt to install it.
SPECIFICATIONS
– 2 speed hydraulic pump
– manual override or hydropneumatic pedal
– chrome piston with adjusting screw
– sliding cylinder jack with handle and rating scale
– polycarbonate protection to protect the operator from splinters
– table height adjustable 12 positions
– winch-assisted up and down movement of the table
– 2 oversized pins to hold the table in place
– 226x136x55mm sliding drip tray
– large manometer
– reversible V-shaped support block, including punch kit and protective
polycarbonate
– nominal capacity (safe working load) : 30T
– dimensions : 1800x770x505mm
– net weight: 200Kg
– standards: 2006/42/EC, EN 693:2001+A2:2011
– lifetime : 8 years
SAFETY INSTRUCTIONS
This press has been designed for general bending, toughening, axis and bearing extraction work etc. Never use it for applications that should not be performed by a press. Always use the appropriate tool for each specific task. Handle the press correctly and ensure that all parts and components are in good condition and that no parts are missing prior to its use.
The press should only be used by authorized person should having read carefully and understood the contents of this manual. All other persons, especially children, must be kept out of the work area.
Always position the press against a wall. If the press is situated in the open workshop, it is essential that a guard be placed at the rear of the unit. The press foot need to be amounted on the ground!
Make sure that the operator must wear protective cloth, gloves, safety helmet, shoes and ear protector during operating. To avoid accidents, always be aware of any on-going work on the machine. Also, always stay focused on the job to be done.
Do not modify the press in any way. Safety valve should not be tampered with under any circumstances.
Never exceed the rated capacity of the press and V-blocks.
Non-compliance with these instructions may result in injury or damage to the
user, the press or the piece being manipulated.
The manufacturer accepts no responsibility for the improper use of the press
or the component handled.
TECHNICAL DATA
TECHNICAL DESCRIPTION
PNEUMATIC AND MANUAL PRESS
- Oil tank
- Winch handle
- V-blocks
- Spare parts tray
- Foot
- Working table
- Pump with pressure gauge
- Cylinder
- Protective cover
- Dust cover
- Hydropneumatics pump
BEFORE USING THE PRESS
LEGS ASSEMBLY
Step 1: Assembled part
1 & part 2 with part 3,4,5 then fix the screw nut.
Step 2: Fix 4 screws of part 6 into ground.
PUMP HANDLE ASSEMBLY
DRAIN THE HYDRAULIC CIRCUIT
**Hydropneumatic pump**
Step 1: Pull out the hose and screw nut of part 9, 10 from part 8.
Step 2: Connect the hose part 11 with part 8
Step 3: Pull out part 12
USE AND OPERATION
Make sure every parts are fixed and tightened and the press should be placed on a firm, regular and horizontal surface. Ensure table at proper position and lock the table by the axles. Leaving enough space around the press while it is in operation so that it is always easily accessible. The V-blocks must be used by pair, not by piece. Only one authorized person having read carefully and understood the contents of this manual is allowed to operate the press. Only for hydropneumatic pump: working air pressure 9-12bar (OH0931) or 10-13bar (OH0951).
OPERATION DESCRIPTION
- Close the release valve by turning it to the right until it is firmly closed.
- Activate the pump until the piston approaches the piece.
- Align the piece and the piston so that the piece is properly cantered.
- Activate the pump to apply pressure to the piece.
- When the work is finished, stop the pump and open the release valve to remove the piece.
SADDLE AND PIN SETS OPERATION
BLOCKERS OPERATION
MOVEABLE CYLINDER OPERATION
WORKING TABLE OPERATION
MAINTENANCE INSTRUCTION
CAUTION
- Do not use damaged/deformed product. If abnormal noise or vibration occurs, stop use immediately, then inspect and ask manufacturer for help. It is recommended that this inspection be made by a manufacturer’s authorized repair facility.
- Keep the service jack clean and well lubricated to prevent foreign matter from entering the system. If the jack has been exposed to rain, snow, sand, or grit, it must be cleaned before it is used.
- Store the jack, with pistons completely retracted, in a well-protected area where it will not be exposed to corrosive vapors, abrasive dust, or any other harmful elements.
- Periodically check the condition of the product.
- Store the product in dry and non-corrosion environment.
- Lubricate the axes and moving parts at regular intervals.
- The elements of the press should be kept clean and protected from aggressive conditions at all times.
- Always use original spare parts.
- Owners and /or operators should be aware that repair of this equipment may require specialized knowledge and facilities. It is recommended that an annual inspection of the product be made by a manufacturer’s or supplier’s authorized repair facility and that any defective parts, decals, or safety labels or signs be replaced with manufacturer’s or supplier’s specified parts.
- Any product that appears to be damaged in any way, is found to be worn, or operates abnormally SHALL BE REMOVED FROM SERVICE UNTIL REPAIRED. It is recommended that necessary repairs be made by a manufacturer’s or supplier’s authorized repair facility if repairs are permitted by the manufacturer or supplier.
- Only attachments and/or adapters supplied by the manufacturer shall be use.
DECLARATION OF CONFIRMITY
Nous, We, CLAS EQUIPEMENTS Z. A. de la Crouza 73800 Chignin France
DECLARE THAT, Under our responsibility, the following products:
Model : PRESSE HYDRO-PNEUMATIQUE 30T VERIN COULISSANT DOUBLE COMMANDE / DUAL-
CONTROL HYDRAULIC PRESS 30T SLIDING CYLINDER
Type : OH 0931
Is manufactured in conformity with the European Directive:
· 2006/42/EC · EN 693:2001+A2:2011
Philippe Barrault, 17.06.2020
CLAS EQUIPEMENTS – SAS au capital de 130 000, R.C.S Chambéry : 409 786 944, N°
TVA Intracommunautaire FR 13 409 786 944 Siège social, Z.A de la Crouza
73800 CHIGNIN – FRANCE +33 (0)4 79 72 62 22 – +33 (0)4 79 72 52 86
contact@clas.com –
www.clas.com
CLAS Equipements ZA de la CROUZA
73800 CHIGNIN FRANCE
Tél. +33 (0)4 79 72 62 22
Fax. +33 (0)4 79 72 52 86
OH 0931
PRESSE HYDRAULIQUE 30T VERIN COULISSANT DOUBLE COMMANDE
DUAL-CONTROL PRESS 30T SLIDING CYLINDER
If you need components or parts, please contact the reseller. In case of problems, please contact your authorized technician.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>