LAMONA LAM8877 Built In Condenser Tumble Dryer Instruction Manual

June 13, 2024
Lamona

LAMONA LAM8877 Built In Condenser Tumble Dryer

LAMONA LAM8877 Built In Condenser Tumble Dryer

Installation Instructions

  • Please read the Installation Manual to ensure safe fitting and use of the appliance.
  • The appliance should be fitted by a suitably competent and qualified person.
  • Please keep these instructions in a safe place for future reference.
  • Danger of suffocation. Keep packaging material away from children.

Warning & Safety Information 

Dryer must be securely located and be level

Be aware of the instability of the appliance prior to being fitted into position

Beware of sharp metal edges. Use gloves when handling

2 Person lift

Ensure packaging & transit protectors have been removed before positioning.

If the electricity cable is damaged, it must be repaired by a competent person

Do not push against the Dryer fascia panel or control dial

This appliance is not designed for stacking

Be aware of the instability of the appliance prior to being fitted into position

Do not lean on or use the door to position the appliance

In transit, stand the appliance in an upright position. If necessary, lay on this side.
Warning & Safety Information

Caution: You must wait at least 4 hours before switching the dryer on. This is to allow oil to flow back into the compressor.

Failure to do so could damage the compressor.

Check for visual damage. If damaged, do not use.
See guarantee: What to do if you need to report a problem.

The dryer contains R290, a flammable eco-sustainable refrigerating gas.
Keep open flames and sources of ignition away from the appliance.

Throughout this manual the following warning symbols are used.

Warning for serious injury or death risk

Warning for risk of fire / flammable materials

Important / note for operating the system

Warning for electric shock

Warning for injury or property damage risk

Warning & Safety Information (continued)

Please read these instructions carefully, observing the technical data and specifications. The manufacturer is not responsible if an incorrect installation and use causes injuries and/or damage. Please take appropriate care when installing. This appliance complies with all relevant E.U. Directives

Electrical Connection

For electrical data, refer to the rating label on the front of the dryer cabinet (with the door open) .
Before connecting the tumble dryer, ensure that the connection data on the data plate (fuse rating, voltage and frequency) match the mains electricity supply. If in any doubt, consult a qualified electrician.
Reliable and safe operation of this appliance can only be assured if it has been connected to the mains electricity supply.

WARNING: The electrical safety of this tumble dryer can only be guaranteed when correctly earthed. It is essential that this standard safety requirement is met. Socket outlet and plug must be of the same type.

If in any doubt, please have the wiring system of the building tested by a qualified electrician. LAMONA cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).

Do not connect the tumble dryer to the mains electricity supply by…

  • a multi-socket adapter,
  • multiple connectors
  • an extension lead or similar
  • an external switching device (such as a timer)
  • Do not connect to a circuit that is regularly switched on and off by a utility
    These do not guarantee the required safety of the machine (fire hazard due to the risk of overheating).Warning & Safety Information

The electrical socket must be easily accessible after installation so that the machine can be disconnected from the electricity supply if necessary.
In the event of a fault, the appliance must be isolated from the electrical supply.
Do not touch the appliance when hands or feet are damp or wet.
Avoid damaging the mains plug and cable. If a replacement be required, contact a LAMONA Authorised service agent, or a suitably qualified person.

Caring for the environment

Disposal of the packing material

The environmentally friendly, recyclable packaging is designed to protect the appliance from damage during transportation. All packaging materials should be recycled. Recycling reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites.

Installation overview guide

Installation considerations ………………………….p.6
Safe operating temperatures. …………………………………..p.6
Ventilation and access…………………………………………………..p.6
Dimensions and minimum clearances ………….p.7
Installation ………………………………………………….p.7
Mounting the door furniture. ……………………………………..p.8
Fix the decor door to the dryer. …………………………………p.9
Anti-tilt block ………………………………………………………………….p.9
Profile kitchen ……………………………………………………………….p.10
Plinth preparation. ……………………………………………………….p.10
Ventilation grille – Easy Removable Plinth Kit ………….p.11
Final alignments……………………………………………………………p.11

Installation Considerations

Safe operating temperatures

This appliance is designed to work at temperatures between 15 – 35°C.

DO NOT install in rooms with low temperatures or risk of frost occurring.

A minimum ambient temperature of 15°C is recommended to avoid external condensation.

Reliability of the electronic control unit may be impaired at temperatures below freezing point.
Installation Considerations

There is risk of damage to valves, pumps and hoses if water is allowed  to freeze in the hydraulic circuit.

Ventilation and access
There must be adequate ventilation in the room where the dryer is located to prevent gases from appliances burning other fuels (including open fires), being drawn into the room during use.

**** Do not install behind a lockable door, sliding door, ora door with a hinge on the opposite side to that of the dryer in such a way that a full opening of the dryer door is restricted.`

**** A plinth vent must be fitted

**** The space between the bottom of the dryer
and the floor must not be obstructed.

Dimensions and minimum clearances

Check that the appliance door and fixed door furniture are clear of any obstructions

Dimensions And Minimum Clearances

**** It is recommended not to install the appliance between décor end panels unless it is  placed at the end of arum, where the niche size can be increased due to clearances.

**** Adjust feet. See below.

Installation

Installation

Please see the Howdens default Kitchen Installation Manual set-up for more details.

Mounting the door furniture

  1. Measure, mark and drill the hinge positions.

  2. Screw fix the hinges, to the décor door.
    Mounting the door furniture

Fix the décor door to the dryer.

Fix the décor door to the dryer.

Use the correct spacers, SX = Left. DX = Right.
Do not use impact driver power tools.

Fix the décor door to the dryer.

Anti-tilt block

  • For added safety, an anti-tilt block should be fixed beneath the worktop.
  • There should be no opening in the worktop above the tumble dryer.

Anti-tilt block

Profile Kitchen

Fix 18mm plate below worktop which finishes flush with the bottom edge of the profile.

Fix 18mm plate below the worktop.
Fit flush with the bottom edge of the profile.

Profile Kitchen

We recommend sealing all cut surfaces and ends.

Plinth Preparation

WARNING : A ventilation grille is required for the correct operation of the appliance.
It MUST be fitted.

The Easy Removable Plinth section provides quick and easy access to clean the condenser filter.

Ventilation grille – Easy Removable Plinth Kit

  1. Cut out and edge a section of plinth at the front of the appliance.
    Ventilation grille - Easy Removable Plinth Kit
    Ventilation grille - Easy Removable Plinth Kit
    Ventilation grille - Easy Removable Plinth Kit
    Ventilation grille - Easy Removable Plinth Kit

Final alignments

Adjust the following for final alignment if necessary.

Final alignments

Final alignments

CUSTOMER SUPPORT

Product information correct at the time of publication in April 2021.
The company has a policy of continuous product development and reserves the right to change any products and specifications given in this manual. Subject to the Terms and Conditions of Trading, a copy of the Howdens Terms and Conditions is available upon request.
Copyright © 2021 Hoiden Joinery Ltd. All rights reserved.

How den Joinery Ltd.
Thorpe Road, How den, East Yorkshire. DN14 7PA England
Howdens Cuisines SAS. Z.A. du Bios  Ribault Nord,
1 Rue Calmette, 62880 Vending-le-Veil, Cedex, France

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals