kanto RCF190 Low Profile Fixed TV Mount User Manual
- June 13, 2024
- Kanto
Table of Contents
kanto RCF190 Low Profile Fixed TV Mount User Manual
Thank you for choosing Kanto
Read these instructions fully before assembly and installation. Make sure
there are no defective or missing parts. Do not use defective parts. Kanto
cannot be liable for property damage or injury caused by incorrect mounting,
incorrect assembly, lifting or incorrect use of this product. If there is
hardware missing, or if you are uncertain whether a part is defective, please
contact Kanto directly using one of the methods below.
⚠ CAUTION
The maximum loading weight is 200 lb (91 kg). This mount is intended for use
only with the maximum weights indicated. Use with products heavier than the
maximum weights indicated may result in instability causing possible injury.
The wall you plan to affix the Kanto mount to must be able to support more
than 5 times the weight of the television and the mount combined. Do not use
this product for any purpose other than to mount a VESA compliant TV on a
vertical surface as outlined in this manual. This Kanto mount is not certified
by or affiliated with Video Electronics Standards Assoc (VESA). Improper
installation may cause damage to your TV or serious injury. This product
should not be mounted on steel stud walls or cinder block walls. Consult a
qualified installation contractor if you are unsure about the type of wall you
may have.
Supplied Parts and Hardware
Project Overview
- Select TV Screws and Spacers
- Select Spacers for Irregular TVs
- Attach TV Brackets
- Mount Wall Plate Assembly
- Hang TV
- Level TV
- Secure TV
- Remove TV
IMPORTANT!: Please read this entire document before attempting assembly.
If you have any problems or difficulties while following these instructions,
please contact Kanto directly:
Email: support@kantoliving.com
Toll Free: US & Canada: 1-888-848-2643
Select TV Screws and Spacers
A–I Select Screws
The back of your TV has 4 screw holes in a square or rectangular pattern. This
is where the mount will attach to your TV.
Kanto provides several sizes and lengths of screws. This guide will help you
select the right screws for your TV. You will only use 4 of the provided
screws to attach your TV the rest are not needed.
J–K Select Spacers
Plastic spacers are also provided in 2 thicknesses to allow the mount to work with curved TVs, and TVs that have recessed mount holes, protrusions, or inputs in the way. They can also be used to prevent the TV screws from going too deep and damaging your TV. You may not need spacers for your TV.
Select Spacers for Irregular TVs
Spacers can be used to provide clearance around protrusions on the back of your TV, or to accommodate a curved TV. You may need to use longer screws.
Attach TV Brackets
WARNING
Do not lay the TV face down on its front. Use a wall or TV stand
Mount Wall Plate Assembly (Wood Stud Wall)
⚠ CAUTION
Make sure the supporting surface will support the load limits outlined in the
caution on page two. Tighten lag bolts (O) until the wall plate is snug
against the wall.
Do not over tighten the lag bolts (O). Each lag bolt must be located in the
middle of a wood stud.
Mount Wall Plate Assembly (Concrete Wall)
⚠ CAUTION
Make sure the concrete or brick wall is at least 4” thick. Make sure the
anchor is seated completely flush with the concrete surface even if there is
another layer of material, such as drywall. If drywall is over 5/8” thick,
custom lag bolts must be used. Concrete must be a minimum of 2000 psi in
density.
Hang TV
Level TV
Secure TV
Remove TV
https://www.kantoaudio.com/
Facebook
Twitter
YouTube
Instagram
Limited Warranty to Original Purchaser
Kanto Living Inc. (Kanto) warrants the equipment it manufactures to be free
from defects in material for the limited warranty period of 10 years.
If equipment fails because of such defects and Kanto is notified within 10
years from the date of shipment with proof of original invoice from an
authorized reseller, Kanto will, at its option, provide replacement parts or
replace the equipment, provided that the equipment has not been subjected to
mechanical, electrical, or other abuse or modifications. Any replacement parts
or replacement units are warranted for 90 days from the day of reshipment to
the original purchaser.
Customers will be responsible for obtaining a Return Authorization Number and
paying shipping costs to return product to a Kanto location or authorized
depot. If the equipment is covered under the warranty provisions above, Kanto
will replace parts or provide a replacement unit, and be responsible for
shipping costs to the customer. Please keep the original packaging to prevent
damage to the product during shipping. Insuring your shipment is also
recommended.
The information in the manual has been carefully checked and is believed to be
accurate. However, Kanto assumes no responsibility for any inaccuracies that
may be contained in the manual. In no event will Kanto be liable for direct,
indirect, special, incidental, or consequential damages resulting from any
defect in the equipment, even if advised of the possibility of such damages.
This warranty is in lieu of all other warranties expressed or implied,
including without limitation, any implied warranty, including any warranty of
merchantability and fitness for any particular purpose, all of which are
expressly disclaimed.
www.kantomounts.com
support@kantoliving.com
Toll Free: 1-888-848-2643
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>