LOVMOR B24-E B27-E Kitchen Base Cabinets Instruction Manual
- June 16, 2024
- LOVMOR
Table of Contents
LOVMOR B24-E B27-E Kitchen Base Cabinets Instruction Manual
Product Overview
PART | DESCRIPTION |
---|---|
A1 | Box side panel – left |
A2 | Box side panel – right |
B | Box bottom panel |
C | Box back panel |
D | Face frame |
E | Toe kick panel |
F | Drawer face panel |
G1 | Drawer side panel – left |
--- | --- |
G2 | Drawer side panel – right |
H | Drawer bottom panel |
I | Drawer back panel |
J | Door panel |
K | Adjustable shelf |
CAUTION
- Be sure to carefully remove all parts from the carton and ensure that there are no damages to any of them.
- The hardware should be kept away from children when unpacking and assembling this product. Two adults are recommended for assembly.
- Follow the instructions in the instruction manual carefully and strictly to ensure that the product is assembled and operates as intended.
- Do not tighten all the screws until all the adjacent parts have been properly connected. Please do not throw away extra screws. Please refer to the actual product for the screw hole position.
HARDWARE CONTENTS
AA Glide and runner profile x 2
Included:
5/8″ Flat Head Phillips Screw x 10
*Two additional pieces are included as an extra
BB Adjustable drawer clips x 2
Included:
5/8″ Flat Head Phillips Screw x 4
3/8″ Flat Head Phillips Screw x 4
CC Soft – close hinge x 4 Be careful the length of the screws.
Included:
1/2” Flat Head Phillips Screw x 8
3/4” Round Head Phillips Screw x 4
DD Wood corner block x 4
Included:
1” Flat Head Phillips Screw x 8
**EE Corner brace x 13
**
Included
1/2” Round Head Phillips Screw x 52
**FF Adjustable shelf clip x 4
**
**GG 1” Flat head Phillips screw x 3
**
**HH Rubber bumper x 8
**
TOOLS REQUIRED (NOT INCLUDED)
INSTALLATION OVERVIEW
Use 1/2” round head phillips screw x 10
Use 1/2” round head phillips screw x 10
Use 1/2” round head phillips screw x 2
Use 1/2” round head phillips screw x 2
Use 1/2” round head phillips screw x 8
Use 1/2” round head phillips screw x 20
Use 5/8” flat head phillips screw x 4
Use 5/8” flat head phillips screw x 4
Use 5/8” flat head phillips screw x 4
Be careful of the screw type.
Use 3/8” flat head phillips screw x 4
Be careful of the screw type.
Insert the drawer on the extended runner. Tosecure the drawer clips with the
runner, push the drawer in. Upon successful locking, a click can be heard.
Ensure that the hook on each runner profile fits into the corresponding holes
on the drawer back panel.
To level the drawer, use the green spur gears 1 to adjust drawer left and
right, the green spur gears 2 to adjust drawer up and down, and the green spur
gears 3 to adjust drawer inside and outside.
To take the drawer out, push the green clips at the same time to unlock drawer
clips.
Use 1/2” flat head phillips screw x 4
Use 3/4” flat head phillips screw x 4
If the door is not level when it is installed, the customer will need to turn
the screw clockwise to extend the hinge or counterclockwise to shorten the
hinge.
Some products may have hinges pre-installed.
Use 1” flat head phillips screw x 8 (2 screws for 1 corner block)
Dear customers,
Thank you for purchasing our product. If you require assistance, please
contact the customer service team at the retailer where you purchased the
product. The customer service team will be happy to assist you.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>