LOKI PLUGIN Key Fob Pairing for Tesla Model X Feature User Guide
- June 8, 2024
- LOKI
Table of Contents
2022.08.17
PLUGIN LOKI
KEY FOB PAIRING
FOR TESLA MODEL X FEATURE
USER GUIDE
Plugin Key Fob Pairing for Model X Feature
INTRODUCTION
To key for pairing for Model X , the LOKI module, the LC003-CX cable, the
clean key (or several) and BLE dongle with the activated plugin are used.
Before turning on the module, you must connect BLE dongle to any port of the
USB module.
The module itself is connected by LC003-CX cable to the diagnostic CAN port of
the vehicle under the monitor.
To work plugin you need to connect to the Internet.
WARNING! The plugin cannot untie an existing key or pairing the being in
the use key.
The theoretical number of keys that can be pairing to a car is 20.
In general, the pairing process is as follows:
- Connecting the module to the vehicle, reading the existing list of keys;
- Connect the module to the clean key;
- Provision procedure for entering data into the key;
- Pairing procedure for directly pairing the key to the vehicle.
CONNECTION TO THE VEHICLE
The vehicle must be switched on, ignition is not necessary.
After connecting the module with the LC003-CX cable, you must go to the key
pairing window.
If the connection is successful, a list of keys in the BCCEN module and data about the vehicle and dongle will be displayed.
KEY PAIRING
To connect to the key it is necessary to bring it to the module at a distance
of up to 70cm (closer – better), and start a key search by the button “Start
Key Discovery”, after the dongle initialization, you need to double-click the
front trunk button to wake the key.
After discovery, the key will appear in the list.
After the key is discovered, you need to connect to it, just click on the “Connect” of the desired key in the table. As soon as the corresponding inscription appears in the log – press three times on the front trunk button to confirm the connection.
After reading the data from the key, it is considered connected.
The status of the key can be seen in the SE State field where:
– Personalization – Clean Key, ready for Provision procedure;
– Active – A key that has passed the Provision procedure, is waiting to
execute the Pairing procedure;
– Paired – Paired key after Pairing procedure.
WARNING! The key transition from the Personalization state to all
subsequent states is irreversible.
PREPARING THE PAIRING KEY (PROVISION)
**WARNING!** Once this procedure is started, the key cannot be used to
paired to another car.
To perform the Provision procedure, just click on the corresponding menu item,
the program will automatically configure the key for the connected vehicle and
prepare it for pairing.
Information about the end of the procedure will appear in the log.
If the key was not clean, the log will look like this.
After successfully completing the Provision procedure, you can proceed with the Pairing procedure.
PAIRING THE KEY (PAIRING)
To perform the Pairing procedure, just click on the corresponding menu item, the program will automatically attach the key to the connected vehicle.
After you complete the pairing procedure, you need to restart the BCCEN block and read the key list to ensure that the pairing succeeds.
The pairing procedure of the first and all subsequent keys is not different, so if necessary, pairing several keys procedure should be repeated for each of them, the old keys will not be disconnected and will continue to work.
Contacts
MSG Equipment
HEADQUARTERS AND PRODUCTION
MSG equipment
18 Biolohichna st.,
61030 Kharkiv
Ukraine
+38 057 728 49 64
+38 063 745 19 68
E-mail: sales@servicems.eu
Website: servicems.eu
REPRESENTATIVE OFFICE IN POLAND
STS Sp. z o.o.
ul. Modlińska, 209,
Warszawa 03-120
+48 833 13 19 70
+48 886 89 30 56
E-mail: sales@servicems.eu
Website: msgequipment.pl
TECHNICAL SUPPORT
+38 067 434 42 94
E-mail: support@servicems.eu
NOTES
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>