kanto SDX600 Full Motion Anti Theft Security TV Mount User Manual

June 4, 2024
Kanto

kanto logo

User Manual
SDX600
kanto SDX600 Full Motion Anti Theft Security TV
Mount

FULL MOTION ANTI-THEFT SECURITY TV MOUNT

SDX600 Full Motion Anti Theft Security TV Mount

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig

Supporting your digital lifestyle™

Thank you for choosing Kanto
Read these instructions fully before assembly and installation. If you do not understand these directions or have any doubts about the safety of the installation, please consult a  qualified installation contractor. Make sure there are no defective or missing parts.
Do not use defective parts. Kanto cannot be liable for property damage or injury caused by incorrect mounting, incorrect assembly, lifting, or incorrect use of this product. If there is hardware missing, or if you are uncertain whether a part is defective, please contact Kanto directly using one of the methods below.
CAUTION
The maximum loading weight is 100 lb (45 kg). This mount is intended for use only with the maximum weights indicated.
Use with products heavier than the maximum weights indicated may result in instability causing possible injury. The wall you plan to affix the Kanto mount to must be able to support more than 5 times the weight of the television and the mount combined. Do not use this product for any purpose other than to mount a VESA-compliant TV on a  vertical surface as outlined in this manual. Improper installation may cause damage to your TV or serious injury. This product should not be mounted on steel stud walls or cinder block walls. Consult a qualified installation contractor if you are unsure about the type of wall you may have.

1-888-848-2643

support@kantoliving.com

See the installation video online at: www.kantomounts.com/resources

Supplied Parts and Hardware

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig2kanto SDX600 Full Motion Anti
Theft Security TV Mount - fig3

Required Tools Wood stud wall Concrete wall

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig4| |

Project Overview

  1. Select TV Screws and Spacers
  2. Select Spacers for Irregular TVs
  3. Disassemble
  4. Attach TV Bracket
  5. Mount Wall Plate Assembly IMPORTANT!: Please read this entire document before attempting assembly.
  6. Til
  7. Hang TV
  8. Level IV
  9. Secure TV
  10. Manage Cables

If you have any problems or difficulties while following these instructions, please contact Kanto directly:
Email: support@kantoliving.com
Toll Free: US & Canada: 1-888-848-2643

Select TV Screws and Spacers

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig7

1.1 A–H Select Screws
The back of your TV has 4 screw holes in a square or rectangular pattern. This is where the mount will attach to your TV. Kanto provides several sizes and lengths of screws.  This guide will help you select the right screws for your TV. You will only use 4 of the provided screws to attach your TV – the rest are not needed.

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig8

1.2 I–K Select Spacers
Plastic spacers are also provided in 3 thicknesses to allow the mount to work with curved TVs and TVs that have recessed mount holes, protrusions, or inputs in the way. They can also be used to prevent the TV screws from going too deep and damaging your TV. You may not need spacers for your TV.

Select Spacers for Irregular TVs

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig9kanto SDX600 Full Motion Anti
Theft Security TV Mount - fig10

*Optional

Spacers can be used to provide clearance around protrusions on the back of your TV or to accommodate a curved TV. You may need to use longer screws.

Disassemble

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig11

Attach TV Brackets

WARNING

Do not lay the TV face down on its front. Use a wall or TV stand.
Use whichever holes and slots work with your TV’s VESA pattern.kanto SDX600
Full Motion Anti Theft Security TV Mount - fig12

*Optional


Only applicable if using M4 / M5 / M6 screw

5a. Mount Wall Plate Assembly (Wood Stud Wall)

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig13

Mount height depends on TV size, viewing position, and personal preference.

CAUTION

Make sure the supporting surface will support the load limits outlined in the caution on page two. Tighten lag bolts (P) until the wall plate is snug against the wall. Do not over-tighten the lag bolts (P). Each lag bolt must be located in the middle of a wood stud.

5b. Mount Wall Plate Assembly (Concrete Wall)

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig16

Mount height depends on TV size, viewing position, and personal preference.kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig17

CAUTION
Make sure the concrete or brick wall is at least 4” thick. Make sure the anchor is seated completely flush with the concrete surface even if there is another layer of material, such as drywall. If drywall is over 5/8” thick, custom lag bolts must be used. Concrete must be a minimum of 2000 psi in density.

Tilt

  • Adjust Arm Tension (Optional)

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig18

Hang TV

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig19

Level IV

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig20

CAUTION

As you adjust the top leveling screw, you will need to adjust the lower locking screw. Be sure to keep the locking screw engaged on the horizontal plate, especially when using the tilt feature.

Secure TV

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig21

  • Two slots are provided on the security bracket. Use the slot that allows the highest position, depending on leveling adjustment.

Note: You can install the security screw on whichever side is easiest.

Manage Cables

kanto SDX600 Full Motion Anti Theft Security TV Mount -
fig22kanto SDX600 Full Motion Anti
Theft Security TV Mount - fig23      www.kantoaudio.com

Limited Warranty to Original Purchaser
Kanto Living Inc. (Kanto) warrants the equipment it manufactures to be free from defects in material for the limited warranty period of 5 years.
If equipment fails because of such defects and Kanto is notified within 5 years from the date of shipment with proof of original invoice from an authorized reseller, Kanto will,  at its option, provide replacement parts or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.  Any replacement parts or replacement units are warranted for 90 days from the day of reshipment to the original purchaser.
Customers will be responsible for obtaining a Return Authorization Number and paying shipping costs to return the product to a Kanto location or authorized depot. If the equipment is covered under the warranty provisions above, Kanto will replace parts or provide a replacement unit, and be responsible for shipping costs to the customer. Please keep the original packaging to prevent damage to the product during shipping. Insuring your shipment is also recommended.
The information in the manual has been carefully checked and is believed to be accurate. However, Kanto assumes no responsibility for any inaccuracies that may be contained in the manual. In no event will Kanto be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect in the equipment, even if advised of the possibility of such damages. This warranty is in lieu of all other warranties expressed or implied, including without limitation, any implied warranty, including any warranty of merchantability and fitness for any particular purpose, all of which are expressly disclaimed.

kanto logo

www.kantomounts.com
support@kantoliving.com
Toll Free: 1-888-848-2643

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals