Kogan KAWM6WF53PA Wi-Fi AC1200 Whole Home Mesh 3 Pack User Guide
- June 13, 2024
- Kogan
Table of Contents
USER GUIDE
WI-FI AC1200 WHOLEHOME MESH
(3 PACK, WI-FI 5)
KAWM6WF53PA
COMPONENTS LIST
- Mesh3 Node (x3)
- Power Adapter (x3)
- Ethernet Cable
- User Guide
OVERVIEW
Wall mounting hole
Used to fix the device to the wall. Recommended specifications are:
- Screws: PA3x14 mm; head diameter: 5.2 mm; head thickness: 1.8 mm
- Plastic anchor: inner diameter: 2.4 mm; length: 26.4 mm
INSTALLATION
Install the KoganMesh App
Download the KoganMesh App onto your mobile device by searching for KoganMesh
in App Store or Google Play or by scanning the QR code.
Then install the KoganMesh App.
http://116.62.16.51/down/Kogan
Available for iOS and Android
Connect the Primary node:
The first node you set up functions as the primary node, while the rest are
referred to as the secondary nodes.
- Power off your modem and remove its battery (if any).
- Use the included Ethernet cable to connect a LAN port of your modem or the Ethernet jack to the (WAN/LAN) port of one of the nodes. This node is your primary node.
- Reinstall its battery and power on your modem.
- Use the included power adapter to connect the primary node to a power source, the LED indicator lights solid green. Wait about for 40 seconds. The system completes start-up when the LED indicator blinks green.
Connect the primary node to the internet
-
Go to the Wi-Fi network list on your mobile device, select the SSID of the primary node and enter its password. The SSID and password are specified on the bottom label of any node.
-
Run the KoganMesh App and follow the onscreen instructions to connect the primary node to the internet. After the primary node is connected to the internet, its LED indicator lights solid green.
Connect the secondary nodes to the internet
-
Place each node:
• In a high & open area
• Ensure that there are less than two walls between any two nodes.
• Keep your nodes away from electronics with strong interference, such as microwave ovens, induction cookers and refrigerators.
-
Use other power adapters to connect the remaining secondary nodes to power outlets, the LED indicators will turn solid green. Wait for about 40 seconds. The secondary node is connecting to another node when its LED indicator blinks green.
-
Observe the LED indicator of the secondary nodes until their LED indicators are one of the following colours:
| Solid Green| Good Connection
---|---|---
| Solid Yellow| Fair Connection
| Solid Red| Disconnected -
If a node’s LED indicator does not light solid green, you can relocate it ensuring you avoid obstructions and any electronic interference.
To access the internet:
- Wired devices: Connect wired devices to the LAN ports of your nodes.
- Wireless devices: Connect wireless devices to the Wi-Fi network using the SSID and WiFi password you set.
- To manage the network anytime anywhere, tap “ ” icon in the app and use your account to login.
SPECIFCATIONS
| Input | 100 – 240 V, AC, 50/60 Hz, 0.4 A |
|---|---|
| Output | 12 V, DC 1 A |
| Operating Temperature | 0-40°C |
| Operating Humidity | (10-90) % RH, non-condensing |
FAQ
Q1: How can I remove a node from my Wi-Fi network?
A1: Tap the node on the KoganMesh App, tap ... in the upper-right corner and choose Delete. Note: Removing operation restores the node to factory settings.
Q2: Can I add another new set of nodes to expand my network coverage?
A2: Yes. Run the KoganMesh App, tap Settings in the lower-right corner, tap Add nova and follow the on-screen instructions.
Q3: How to restore my network to factory settings?
A3: With your nodes powered on, hold the Reset button of your primary node down using a sharp item (such as a pin) for about 6 seconds and release it when the LED indicator blinks fast. Your network is reset successfully when the LED indicator lights solid green then blinks slow again. All nodes will be restored to factory settings.
Q4. My 2.4 GHz Wi-Fi-enabled devices, such as a home security camera, cannot connect to my nova Wi-Fi network. What should I do?
A4: Please try the following solution: Step 1: Connect your smart phone used during setup to your Wi-Fi network. Step 2: Run the KoganMesh App, tap Settings, Smart Assistant and Enable. Your smart phone will connect to the 2.4 GHz Wi-Fi network. Step 3: Use the smart phone to set up your 2.4 GHz Wi-Fi- enabled device following the prompts in the app.
Disposal
This marking indicates that this appliance should not be disposed with other
household wastes. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources.
NOTES
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com