RAB Lighting R4R89FA120WS Adjustable Recessed Retrofit and Gimbal Retrofit Instructions
- June 13, 2024
- RAB Lighting
Table of Contents
INSTRUCTIONS
4″ Recessed Retrofit FA
R4R89FA120WS Adjustable Recessed Retrofit and Gimbal Retrofit
RAB Lighting is committed to creating high-quality, affordable, well-designed
and energy-efficient LED lighting and controls that make it easy for
electricians to install and end users to save energy. We’d love to hear your
comments. Please call the Marketing Department at 888-RAB-1000 or email:
marketing@rablighting.com 
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and
all applicable local codes. Proper grounding is required for safety. THIS
PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED.
WARNINGS:
- Risk of electrical shock. Disconnect power at fuse or circuit breaker before installing or servicing.
- To prevent early lamp failure, lamp should only be installed in operating environments ranging between-30 C and +40 C (-22°F and+104°F). . No user serviceable parts inside. To avoid electrical shock do not disassemble product.
- Risk of fire or electric shock, LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Risk of fire or electric shock, Install this kit only in luminaires that have the construction features and min dimensions shown in the Figure 1 and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder terminals, Instead installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors.
- This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.
- This device is not intended for use with emergency exits.
- This retrofit kits suitable for wet locations luminaires specified as below: Type Non IC; Type IC; Covered ceiling , Uncovered ceiling. Installers should examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
NOTE 1: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCCRules.
These limits are designed to provide reasonable protection against harmful
interference in aresidential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment
Note: These instructions do not cover all details or variations in
equipment nor do they provide forevery possible situation during installation,
operation or maintenance.
WHAT’S IN THE BOX
TOOLS NEEDED
The Recessed LED Downlight is designed to fit into a 4″housing. No tools are necessary for installation.
MIN.LUMINAIRE DIMENSION
OPTIONAL ACCESSORIES
Goof ring
RFLED-GOOF 4R-6R-W
For use with 4 housing applications
INSTALLATION INSTRUCTIONS
- Make sure the power is turned off at the source to the recessed housing that you are installing the fixture in. Remove existing trim and CFL or Incandescent bulbs.
- Screw the E26 adapter into the socket inside the housing. (Fig. 2)
- Select desired CCT level using switch on driver box. (Fig. 3)
- Plug E26 base cable connection into the recessed housing. (Fig-4)
- Carefully route wires into fixture, simply slide the trim and metal friction clips into the housing. (Fig. 5)
- Push the LED trim into the housing until flush with ceiling. (Fig. 6)
DIMENSIONAL DRAWINGS
Easy
Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly – sales@rablighting.com
Free Lighting Layouts
Answered online or by request
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found
at rablighting.com/warranty.
© 2022 RAB LIGHTING Inc.
Cranbury, New Jersey 08512 USA
R4RX9FA-IN-0722
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>