BLUETTI EP500 Portable Power Station User Manual
- June 6, 2024
- Bluetti
Table of Contents
Portable Power Station EP500
USER MANUAL
Please read this manual before use and follow its guidance. Keep this manual
for future reference.
Detailed user manual please access:
WWW.BLUETTI.COM
QUICK GUIDE
UPS & LOAD
Advanced Settings: Parameters and working mode can be tweaked in Advanced mode.
Economic Mode: For areas with stable power supply, battery pack will be mainly charged by
PV. UPS Mode: For areas with unstable power supply, loads will be powered by the battery pack once power outage occurred.
5120Wh x DOD x n < (load W) = charging time (unit: hrs)
Note: DOD indicates Depth of Discharge, n indicates inverter efficiency, DOD=90% , n=90%.
CHARGING
Split Phase Mode
Boost your power station from 2000W@200-120V to 4000W@220-240V
GENERAL SPECIFICATION
Output Specification
Input Specification
Error Code
SAFETY INSTRUCTIONS
Please observe the following Instructions to ensure safety use:
- DO NOT attempt to replace the Internal battery with anything other than authorized replacement battery by yourself.
- DO NOT operate in wet conditions, let unit dry completely before using.
- Ensure proper ventilation while in use and do not obstruct fan openings on use. Inadequate ventilation may cause damage to the power station.
- DO NOT stack anything on top of the power station In storage or In use, vibration and Impact may lead to poor connection to hardware inside.
- DO NOT insert foreign objects into outputs or ventilation holes.
- DO NOT place the power station near heat sources like furnace or ambient heater too close.
- The power station generates the same potentially lethal AC power as household well outlet, please take carefully and keep children away from it.
FREQUENTLY ASKED QUESTIONS
Q. How do I clean for power station?
A. Dry, non-abrasive cloths to wipe will be perfect. The power station is
a versatile tool for various adventures, simple cleaning would be required
from time to time to keep the unit in a good condition.
Q. How do I store my power station?
A. Please store the power station in a dry and cool place at the
recommended temperature. Do not expose the power station to humid environment.
If you want to store it for a long time, please fully charge the battery every
6 months to extend the battery lifetime. Remind to turn off the unit before
storing.
Q. How to claim the warranty?
A. Please place your after sales requirement as the warranty card written
to the platform where you order the product.
Q. Can it be upgraded?
A. The firmware can be upgraded online through OTA, and the parameters of
the machine will be adjusted and optimized.
Abbreviation Explain:
DC/AC = Direct Current / Alternating Current
PV = PhotoVoltaic (Solar power)
BMS = Battery Management System
CS = Charging State
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>