MiBOXER 12W RGB and CCT Floor Lamp Instruction Manual

MiBOXER 12W RGB and CCT Floor Lamp Instruction Manual

Product features

This product uses WiFi + Bluetooth + 2.4G wireless transmission technology, low power consumption, strong anti-interference ability. WiFi + Bluetooth connect network can greatly enhance the connect network experience. When the router is disconnected, Bluetooth can also directly connect and control equipment at close range.

After successful network configuration using [Tuya Smart] app to achieve wireless dimming, remote control, group control, scene control, timing control, music movement, biorhythm, sleep plan, wake plan, one key execution, automation, etc. functions. And it supports 2.4G remote control.

Button instructions

1. Short press to turn ON / OFF
2. Light on status: Long press increase / decrease brightness (Long press and release, then long press to change)
3. Can be paired with the remote within 3 seconds after turning on the light
4. Quickly press 5 times to enter the configuration mode

Compatible with these 2.4G RF remote controls (Purchased separately)

2.4G RF Remote control instruction

1). Linking Code Instructions

⚠ Linking failed if light is not blinking slowly, Please follow above steps again. (Note: Light that have linked can’t link again)

2). Unlinking Code Instructions

⚠ Unlinking failed if light is not blinking quickly, Please follow above steps again. (Note: Light haven’t linked that don’t need to unlink)

3). Auto transmitting & Synchronization (only for remote control)

Remote signal auto transmitting One light can transmit the signals from the remote control to another light within 30m, as long as there is a light within 30m, the remote control distance can be limitless. Dynamic modes auto synchronization Multi lights can synchronize if they are in same dynamic mode and linked with same remote (distance between each light is within 30m)

4). Dynamic mode table selection (only for remote control)

Select dynamic mode table 1: While the light is in static mode, short press ” S+ ” button 5 times quickly until blue light flashes 3 times slowly, static mode is activated successfully. Select dynamic mode table 2: While the light is in static mode, short press ” S- ” button 5 times quickly until yellow light flashes 3 times slowly, static mode is activated successfully.

Dynamic mode table 1 (default)

Dynamic mode table 2 (need to switch manually)

5). “Do Not Disturb” mode is activated and shut down (default

activated)

Turn on “Do Not Disturb” mode (wide using in the area which have power failure frequently to save energy)
2.4G RF Remote turn on and turn off instruction Turn on “Do Not Disturb” mode: Press “OFF” button three times within three seconds and press “ON” button three times, Activated successfully once led light flashes four times quickly. Attention: Do not disturb mode is activated 1. When the light is OFF status (For example: Use app or remote to turn off light) The light is OFF status once you turn off power and turn on again. (User must turn off and turn on power twice times to activate light or use APP / remote to activate light) 2. When the light is ON status The light remains in the ON status when you power off and then power on the light once.
Turn off “Do Not Disturb” mode: Press “ON” button three times within three seconds and press “OFF” button three times, closed successfully once led light flashes four times slowly. Attention: If you turn off and then turn on the power once the “Do Not Disturb” mode has been deactivated, the light will always remain in the “ON” status.
App turn on and off “Do Not Disturb” mode instruction (check details in page 8)

Smartphone APP control instruction

Network Configuration (Don’t support 5G router)
1. Download and install [Tuya Smart] app
Search for [Tuya Smart] in Apple or Google store or scan following QR code to download and install the app. Please open the app click ” Register ” button to create account while using it in the first time, Log in directly if you already had account.

https://miboxer.com/light/app/tuya.html

2. Network Configuration
(1) Connect floor lamp with power supply.
(2) Method to enter the pairing network mode (Note: Factory default is Pairing Network Mode)
Method 1: Press the ” ” button quickly 5 times, and the light will flash rapidly.
Method 2: Power off and then power on the light fixture 3 times, and the light will flash rapidly.
(3) Connect phone with home WiFi network in the 2.4GHz frequency.
(4) Open homepage of app and click ” + ” button at the upper right corner of page.
(5) Click ” Lighting ” on the left side of page and then click ” Light Source (BLE+Wi-Fi) ”
(6) Follow app prompts to complete configuration.

App turn on and off “Do Not Disturb” mode (default activated)
Click the light which need to be set up or group control — click “More”— click “Power-on behavior”–turn on or off

Alexa voice control instruction

Please add device into [Tuya Smart] app (check details in page 7), then start following steps

Google Home voice control instruction

Please add device into [Tuya Smart] app (check details in page 7), then start following steps

DMX512 LED Transmitter Control

DMX512 LED Transmitter Link/Unlink

1 Follow instruction of DMX512 transmitter (FUTD01), Choose the zone for the light by pressing ” + ” or ” – ” (e.g. “CH12” means zone 12)

Link
Power off for 10 seconds, then power on again. Alternatively, you can briefly press the ” ” button to turn on the light.

Short press ” SET ” 3 times within 3 seconds while the indicator of controller is ON

Link is done once indicator of controller flashes 3 times slowly

Unlink
Power off for 10 seconds, then power on again. Alternatively, you can briefly press the ” ” button to turn on the light.

Short press ” SET ” 5 times within 3 seconds while the indicator of controller is ON

Unlink is done once indicator of controller flashes 10 times quickly

⚠ If the link or unlink failed, please follow the above steps again.

Installation Method

Attention

1. Please turn off power supply before installation.
2. Please ensure input voltage to be same as requirements from device.
3. Don’t disassemble device if you are not expert, otherwise it will damage it.
4. Please do not use the light in the place with widely range metal area or strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>