MIBOXER FUT043A 3 in 1 LED Controller Kits Instruction Manual

MIBOXER FUT043A 3 in 1 LED Controller Kits

Product Information

The Subordinate New Brand 3 in 1 LED Controller Kits (2.4G) is a product that uses new 2.4GHz wireless transmitting technology with low power consumption and strong network building capabilities. It has an anti-interference feature and can be used with MiBoxer 2.4GHz gateway for wireless dimming color, remote control, ming control, group control, music rhythm function. The product supports 2.4G RF remote control and has 16 million colors to choose from. The color temperature is adjustable, and the brightness and saturation can be dimmed. The remote control distance is 30m, and it has auto-transmitting and synchronization features. It can be controlled through a smartphone app (2.4GHz gateway needed), and third-party voice control is possible (2.4GHz gateway needed). The product is DMX512 controllable (Only for RGB+CCT output mode DMX512 LED transmitter is needed).

Product Usage Instructions

Set up output mode: To set up the correct output mode based on the feature of lights, press the SET button continuously to switch output mode. The output mode sheet confirms the output mode based on the color of the indicator.

2.4G RF Remote control instructions:
There is no need to match code since it’s already matched in the factory setting. To link the code:

1. Power off for 10 seconds and power on again or short press SET one time.
2. Short press ON button three times within three seconds.
3. The lights blink three times slowly, which means linking is done successfully. If the light is not blinking slowly, follow the above steps again. (Note: The light that has linked can’t link again.)

To unlink the code:

1. Power off for 10 seconds and power on again or short press SET one time.
2. Short press ON button five times within three seconds.
3. The lights blink ten times quickly, which means unlinking is done successfully. If the light is not blinking quickly, follow the above steps again. (Note: The light that hasn’t linked doesn’t need to unlink.)

Auto transmitting & Synchronization: The product has auto-transmitting and synchronization features. One light can transmit signals from the remote control to another light within 30m, and as long as there is a light within 30m, the remote control distance can be limitless. Multiple lights can synchronize if they are in the same dynamic mode and linked with the same remote (distance between each light is within 30m).

Dynamic mode table selection: To select dynamic mode table 1, while the light is in static mode, short press S+ button five times quickly until the blue light flashes three times slowly, and static mode is activated successfully. To select dynamic mode table 2, while the light is in static mode, short press S- button five times quickly until the yellow light flashes three times slowly, and static mode is activated successfully.

Product features

Made by new 2.4GHz wireless transmiting technology with low power consumption, strong ability to build network automatically and anti-interference. with MiBoxer 2.4GHz gateway to get wireless dimming color, remote control, timing control, group control, music rhythm function. Support 2.4G RF remote control.

Set up output mode

Set up correct output mode based on the feature of lights Setting method: Press “SET” button continuously to switch output mode (attention: it will log out without operation within 3 seconds)
Output mode sheet ( confirm output mode based on color of indicator)

4G RF Remote control instruction

Attention: No need to match code since its already matched code in factory setting

Linking Code Instructions

1. Power off 10 seconds and power on again or short press “SET” one time.
2. Short press ” ON ” button 3 times within 3 seconds.
3. Lights blink 3 times Lights blink 3 times Lights blink 3 times

Linking failed if light is not blinking slowly, Please follow above steps again. (Note: Light that have linked can’t link again)

Unlinking Code Instructions

1. Power off 10 seconds and power on again or short press “SET” one time.
2. Short press ” ON ” button 5 times within 3 seconds.
3. Lights blink 10 times quickly means unlinking is done successfully.

Unlinking failed if light is not blinking quickly, Please follow above steps again. (Note: Light haven’t linked that don’t need to unlink)

Auto transmi?ng & Synchronization (only for remote control)

• Remote signal auto transmiting
  One light can transmit the signals from the remote control to another light within 30m, as long as there is a light within 30m, the remote control distance can be limitless.

• Dynamic modes auto synchronization
  Multilights can synchronize if they are in same dynamic mode and linked with same remote (distance between each light is within 30m)

Dynamic mode table selection (only for remote control)

• Select dynamic mode table 1:
  While the light is in static mode, short press “ S+ ” button 5 times quickly until blue light flashes 3 times slowly, static mode is activated successfully.

• Select dynamic mode table 2:
  While the light is in static mode, short press “ S- ” button 5 times quickly until yellow light flashes 3 times slowly, static mode is activated successfully.

Dynamic mode table 1 (default)

Adjustable

2| Automatic color change
3| Sam
4| Gemstone
5| Twilight
6| American
7| Fat Tuesday
8| Party
9| Slow Color Splash

Dynamic mode table 2 (need to switch manually)

Adjustable

2| White light Gradual change
3| RGB gradual change
4| Seven colors jump to change
5| Jump to change randomly
6| Red light gradual change

+Flash 3 times

7| Green light gradual change

+Flash 3 times

8| Blue light gradual change

+Flash 3times

9| White light gradual change

+Flash 3 times

PWM high frequency / low frequency switching

• Switch to high frequency (16KHz):
  Press “OFF” button 1 time within three seconds and press “ON” button 5 times, Activated successfully once led light flashes 2 times quickly.

• Switch to low frequency (250Hz):
  Press “ON” button 1 time within three seconds and press “OFF” button 5 times, Activated successfully once led light flashes 2 times slowly.

“Do Not Disturb” mode is activated and shut down (default activated)

Turn on “Do Not Disturb” mode (wide using in the area which have power failure frequently to save energy)

• 2.4G RF Remote turn on and turn off instruction
  Turn on “Do Not Disturb” mode:
  Press “OFF” button three times within three seconds and press “ON” button three times, Activated successfully once led light flashes four times quickly.
  Attention: Do not disturb mode is activated

1. When the light is OFF status (For example: Use app or remote to turn off light) The light is OFF status once you turn off power and turn on again. (User must turn off and turn on power twice times to activate light or use APP / remote to activate light)
2.  When the light is ON status The light is ON status once you turn off and turn on power one time.

• Turn off “Do Not Disturb” mode:
  Press “ON” button three times within three seconds and press “OFF” button three times, closed successfully once led light flashes four times slowly.
  Attention: The light will be always “ON” status if you turn on and turn off power once user closed “Do Not Disturb” mode.

DMX512 LED Transmitter Control

DMX512 LED Transmitter Link/Unlink

Follow instruction of DMX512 transmitter (FUTD01), Choose the zone for the light by pressing “ + ” or “ – ” (e.g. “CH12” means zone 12)

Link

• The controller is powered off for 10 seconds and then powered on,
  or press “ SET ” button 1 time.

• Short press 3 times within 3 seconds while the indicator of controller is ON

• Link is done once indicator of controller flashes 3 times slowly

Unlink

• The controller is powered off for 10 seconds and then powered on, or press “ SET ” button 1 time.
• Short pr SETess 5 times within 3 seconds while the indicator of controller is ON
• Unlink is done once indicator of controller  flashes 10 times quickly
  If the link or unlink failed, please follow the above steps again.

Attention

• Please turn off power supply before installation.
• Please ensure input voltage to be same as requirements from device.
• Don’t disassemble device if you are not expert, otherwise it will damage it.
•  Please do not use the light in the place with widely range metal area or strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected.

Scan QR code to watch 2.4GHz series video instruction Or enter into following link directly: https://miboxer.com/light/video/1pc_remote.html

References

• Remote Series Video - MiBoxer
• Remote Series Video - MiBoxer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>