MiBOXER 2 Wires 2.4G 2 in 1 LED Controller Instruction Manual

MiBOXER 2 Wires 2.4G 2 in 1 LED Controller

Product Information

The product is a LED controller that adopts widely used 2.4GHz wireless technology with features like low power consumption, long signal transmission, strong anti-interference, etc. It has an auto-transmitting function and is widely used for controlling hotel lighting and home lighting. The product is color temperature adjustable, can dim brightness, uses 2.4G RF wireless transmission technology, has a remote control distance of 30m, supports smartphone app control (2.4GHz gateway is needed), and supports third-party voice control (2.4GHz gateway is needed).

Product Usage Instructions:

Set up output mode:
Set up the correct output mode based on the feature of the lights by pressing the SET button continuously to switch output mode. (Note: It will log out without operation within 3 seconds). Check the output mode sheet to confirm the output mode based on the color of the indicator.

Connect to LED strip diagram:
The controller input voltage must be in accordance with the required voltage of LED Strips. For Single Color Modes, the input voltage is DC12V~48V. For Dual White Modes, the input voltage is also DC12V~48V. Follow the connect to LED strip diagram to connect the LED strip properly.

2.4G RF Remote control instrucon:
Follow the below instructions to link or unlink the 2.4G RF remote control:

Linking Code Instructions:

1. Press the Link/Unlink button on the remote control.
2. Power off for 10 seconds and power on again or short press SET one time or turn on light via the PUSH switch.
3. Lights blink 3 times slowly means linking is done successfully.

Unlinking Code Instructions:

1. Press the Link/Unlink button on the remote control.
2. Power off for 10 seconds and power on again or short press SET one time or turn on the light via the PUSH switch.
3. Short press the I button 5 times within 3 seconds.
4. Lights blink 10 times quickly means unlinking is done successfully.

Compatible with these 2.4G RF remote controls (Purchased separately):

The product is compatible with FUT006, FUT007, B1/B1-B/T1, B2/T2, K1/K1-B, FUT087, FUT087-B, S1-B/S1-W/S1-G, and WL-Box1 2.4G RF remote controls (purchased separately).

Auto transming (2.4G RF remote signal):

The light can transmit a remote signal to another light automatically while the distance between lights is 30m. The remote control distance is unlimited. (Note: all lights must be linked with the same remote control).

PWM high-frequency / low-frequency switching:

Switch to high frequency (16KHz): Press the OFF button 1 time within three seconds and press ON button 5 times. Activated successfully once led light flashes 2 times quickly. Switch to low frequency (250Hz): Press ON button 1 time within three seconds and press OFF button 5 times. Activated successfully once led light flashes 2 times slowly.

Product features

Product adopt the widely used 2.4GHz wireless technology with the features of low power consumption, long signal transmitting and strong anti-interference, etc. Product has auto-transmitting function. Widely used on the controlling of hotel lighting and home lighting.

1. Color temperature adjustable
2. Dim brightness
3. 2.4G RF wireless transmission technology
4. Remote control distance 30m
5. Auto transmitting
6. Support Smartphone app control (2.4GHz gateway is needed)
7. Support third-party voice control (2.4GHz gateway is needed)

Set up output mode

• Set up correct output mode based on the feature of lights
• Setting method: Press “SET” button continuously to switch output mode (attention: it will log out without operation within 3 seconds)

Output mode sheet ( confirm output mode based on color of indicator)

Connect to LED strip diagram

The controller input voltage must be in accordance with the required voltage of LED Strips.

2.4G RF Remote control instruction

Linking Code Instructions

• Power off 10 seconds and power on again or short press “SET” one time or turn on the light via the PUSH switch
• Short press ” I ” button 3 times within 3 seconds
• Lights blink 3 times slowly means linking is done successfully.

Linking failed if light is not blinking slowly, Please follow the above steps again.
( Note : Light that have linked can’t link again)

Unlinking Code Instructions

• Power off 10 seconds and power on again or short press “SET” one time or turn on light via the PUSH switch
• Short press ” I ” button 5 times within 3 seconds
• Lights blink 10 times quickly means unblinking is done successfully

Unlinking failed if the light is not blinking quickly, Please follow the above steps again.
( Note : Light hasn’t linked that don’t need to unlink)

Compatible with these 2.4G RF remote controls (Purchased separately)

Auto transmitting (2.4G RF remote signal)

The light can transmit remote signal to another light automatically while the distance between lights are 30m, the remote control distance is unlimited. (Attention: all lights must be linked with same remote)

PWM high-frequency / low-frequency switching

• Switch to high frequency (16KHz):
• Press the “OFF” button 1 time within three seconds and press the “ON” button 5 times,
• Activated successfully once led light flashes 2 times quickly.
• Switch to low frequency (250Hz):
• Press the “ON” button 1 time within three seconds and press the “OFF” button 5 times,
• Activated successfully once led light flashes 2 times slowly.

“Do Not Disturb” mode is activated and shut down (default activated)

Turn on “Do Not Disturb” mode (wide using in the area which have power failure frequently to save energy)
2.4G RF Remote turn on and turn off instruction Turn on “Do Not Disturb” mode:
Press “OFF” button three times within three seconds and press “ON” button three times, Activated successfully once led light flashes four times quickly.
Attention : Do not disturb mode is activated

1. When the light is OFF status (For example: Use app or remote to turn off light)
   The light is OFF status once you turn off power and turn on again. (User must turn off and turn on power twice times to activate light or use APP / remote to activate light)

2. When the light is ON status
   The light is ON status once you turn off and turn on power one time.

Turn off “Do Not Disturb” mode:
Press the “ON” button three times within three seconds and press “OFF” button three times, and close successfully once the led light flashes four times slowly.
Attention : The light will be always “ON” status if you turn on and turn off the power once the user closed “Do Not Disturb” mode.

PUSH Dimming

Short press PUSH switch:
Turn ON/OFF light

Long press PUSH switch:

• Stepless dimming brightness.
• Long press and release your finger, then repeat long pressing to increase or decrease brightness.

Attention

1. Please turn off the power supply before installation.
2. Please ensure the input voltage to be same as the requirements from the device
3. Don’t disassemble the device if you are not an expert, otherwise, it will damage it.
4. Please do not use the light in place with widely range metal area or strong electromagnetic
5. Please do not use the light in a place with a wide range metal area or strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected

Scan the QR code to watch the 2.4GHz series video instructions Or enter into the following link directly
https://miboxer.com/light/video/loc-remote.html
Made in China

References

• Remote Series Video - MiBoxer
• Remote Series Video - MiBoxer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>