MiBOXER FUT037P 5 In 1 2.4GHz LED Controller Instruction Manual
- May 15, 2024
- MiBOXER
Table of Contents
- MiBOXER FUT037P 5 In 1 2.4GHz LED Controller
- Product features
- Set up output mode
- PUSH Dimming
- Compatible with these 2.4G RF remote controls (Purchased separately)
- DMX512 LED Transmitter Control
- DMX512 LED Transmitter Link/Unlink
- Attention
- Specifications
- FAQ
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MiBOXER FUT037P 5 In 1 2.4GHz LED Controller
INSTRUCTION MANUAL
5 in 1 LED Controller ( 2.4GHz )
Product features
Made by new 2.4GHz wireless transmitting technology with low power consumption, strong ability to build network automatically and anti- interference. with MiBoxer 2.4GHz gateway to get wireless dimming color, remote control, timing control, group control, music rhythm function. Support 2.4G RF remote control.
Set up output mode
Set up correct output mode based on the feature of lights
Settng method: Press “SET” button continuously to switch output mode
(attention: it will log out without opera?on within 3 seconds)
Output mode sheet ( confirm output mode based on color of indicator)
Indicator color| White Light| Yellow Light| Red Light|
Green Light| Blue Light
---|---|---|---|---|---
Output| Single Color| Dual White| RGB| RGBW| RGB+CCT
PUSH Dimming
Short press PUSH switch:
Turn ON/OFF light
Stepless dimming brightness.
Long press PUSH switch:
Long press and release your finger, then repeat long pressing to increase or
decrease brightness.
Compatible with these 2.4G RF remote controls (Purchased separately)
2.4G RF Remote control instruc?on
1). Linking Code Instructions
Power off 10 seconds and power on again or short press “SET” one ?me or turn on light via PUSH switch
Short press ” I ” button 3 times within 3 seconds.
Lights blink 3 times slowly means linking is done successfully.
WARNING: Linking failed if light is not blinking slowly, Please follow above steps again. (Note: Light that have linked can’t link again)
2). Unlinking Code Instructions
Power off 10 seconds and power on again or short press “SET” one time or turn on light via PUSH switch
Short press ” I ” button 5 times within 3 seconds.
Lights blink 10 times quickly means unlinking is done successfully.
WARNING: Unlinking failed if light is not blinking quickly, Please follow above steps again. (Note: Light haven’t linked that don’t need to unlink)
3). Auto transmittng & Synchronization (only for remote control)
4). Dynamic mode table selection (only for remote control)
Select dynamic mode table 1:
While the light is in static mode, short press “ S+ ” button 5 times quickly
until blue light flashes 3 times slowly, static mode is activated successfully.
Select dynamic mode table 2:
While the light is in static mode, short press “ S- ” button 5 times quickly
until yellow light flashes 3 times slowly, static mode is activated
successfully.
Dynamic mode table 1 (default)
| Number | Dynamic Mode | Brightness / Satura�on / Speed |
|---|---|---|
| 1 | Mardi Gras | Adjustable |
| 2 | Automa�c color change | |
| 3 | Sam | |
| 4 | Gemstone | |
| 5 | Twilight | |
| 6 | American | |
| 7 | Fat Tuesday | |
| 8 | Party | |
| 9 | Slow Color Splash |
Dynamic mode table 2 (need to switch manually)
| Number | Dynamic Mode | Brightness / Satura�on / Speed |
|---|---|---|
| 1 | Seven colors gradual change | Adjustable |
| 2 | White light Gradual change | |
| 3 | RGB gradual change | |
| 4 | Seven colors jump to change | |
| 5 | Jump to change randomly | |
| 6 | Red light gradual change |
+Flash 3 �mes
7| Green light gradual change
+Flash 3 �mes
8| Blue light gradual change
+Flash 3 �mes
9| White light gradual change
+Flash 3 �mes
5). PWM high frequency / low frequency switching
Switch to high frequency:
Press “OFF” button 1 time within three seconds and press “ON” button 5 times,
Activated successfully once led light flashes 2 times quickly.
Switch to low frequency:
Press “ON” button 1 time within three seconds and press “OFF” button 5 times,
Activated successfully once led light flashes 2 times slowly.
6). “Do Not Disturb” mode is activated and shut down (default activated)
Turn on “Do Not Disturb” mode (wide using in the area which have power failure
frequently to save energy)
2.4G RF Remote turn on and turn off instruction
Turn on “Do Not Disturb” mode:
Press “OFF” button three times within three seconds and press “ON” button
three times, Activated successfully once led light flashes four times quickly.
Attentton: Do not disturb mode is activated
1. When the light is OFF status (For example: Use app or remote to turn off
light) The light is OFF status once you turn off power and turn on again.
(User must turn off and turn on power twice times to activate light or use APP
/ remote to activate light)
2. When the light is ON status
The light is ON status once you turn off and turn on power one time.
Turn off “Do Not Disturb” mode:
Press “ON” button three times within three seconds and press “OFF” button
three times, closed successfully once led light flashes four times slowly.
Attention: The light will be always “ON” status if you turn on and turn
off power once user closed “Do Not Disturb” mode.
DMX512 LED Transmitter Control
(Purchased separately)
Only for RGB+CCT output mode
DMX512 LED Transmitter Link/Unlink
1. Follow instruction of DMX512 transmitter (FUTD01), Choose the zone for the light by pressing “ + ” or “ – ” (e.g. “CH12” means zone 12)
Link
- The controller is powered off for 10 seconds and then powered on, or press “ SET ” button 1 time.
- Short pr SETess “ SET ” 3 times within 3 seconds while the indicator of controller is ON
- Link is done once indicator of controller flashes 3 times slowly
Unlink
- The controller is powered off for 10 seconds and then powered on, or press “ SET ” button 1 time.
- Short press “ ” 5 times within 3 seconds while the indicator of controller is ON
- Unlink is done once indicator of controller flashes 10 times quickly
WARNING: If the link or unlink failed, please follow the above steps again.
Attention
1. Please turn off power supply before installation.
2. Please ensure input voltage to be same as requirements from device.
3. Don’t disassemble device if you are not expert, otherwise it will damage
it.
4. Please do not use the light in the place with widely range metal area or
strong electromagnetic wave nearby, otherwise, the remote distance will be
seriously affected.
Scan QR code to watch 2.4GHz series video instruction Or enter into following
link directly
https://miboxer.com/light/video/1pc_remote.html
Specifications
- 5 in 1 LED Controller (2.4GHz)
- 16 Million colors to choose from
- Color temperature adjustable
- Dim brightness/Saturation
- 2.4G RF wireless transmission technology
- Remote control distance: 30m
- Supports Smartphone app control (2.4GHz gateway required)
- Supports third-party voice control (2.4GHz gateway required)
- DMX512 controllable (Only for RGB+CCT output mode, DMX512 LED transmitter needed)
FAQ
How does the auto-transmitting feature work?
The auto-transmitting feature allows one light to transmit signals from the remote control to another light within 30m. As long as there is a light within 30m, the remote control distance can be limitless.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>