VIDEX VLF-BA286 LED Bike Light User Manual

: June 13, 2024
: VIDEX

Table of Contents

VIDEX VLF-BA286 LED Bike Light
TECHNICAL PARAMETERS
FEATURES
LIGHTING MODES
OPERATING INSTRUCTION
BATTERY STATUS INDICATION
CHARGING
MAINTENANCE AND SAFETY INSTRUCTIONS
WARRANTY
ENVIRONMENTAL PROTECTION
DIMENSION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VIDEX VLF-BA286 LED Bike Light

TECHNICAL PARAMETERS

VIDEX-VLF-BA286-LED-Bike-Light-FIG-1 VIDEX-VLF-
BA286-LED-Bike-Light-FIG-2

Output;
Runtime;
The beam distance;
Intensity;
Beam angle;
Correlated color temperature;
LED type;
Compatible battery;
Charging port type, voltage and current;
Charging time;
Dust and moisture protection level;
Impact resistance;
Product sizes;
Product weight;
Color; black;
Optical system type; optical lens;
Materials: anodized aluminum, polycarbonate.

Note: The output porometers results ore tested with ,.._ o stock battery Videx 21700 4000mAh. The above mentioned parameters may vary between environments and actual batteries used.

‘The mode runtime is the occumuloted time, including reduced output levels with the overheat protection enabled.

FEATURES

Max brightness 2000 Lm with compact body;
The light flux stabilization system prevents the brightness fluctuations over the runtime;
Full aluminum quick-release bike holder;
Replaceable batteries;
Separate 4-level battery indicator;
Built-in type-c port for charging on the go;
Water resistance IP68 (short-term immersion underwater to a depth of 2 meters);
Thick shockproof and anti-rolling shell;
Any brightness mode has flash option;

INCLUDED

Flashlight VLF-BA286;
Li-ion battery Videx 21700 4000 mAh;
Bike holder;
Charging cable;
Adapter for 18650 battery;
Spare silicone pads;
Spare a-rings;
Hex keys;
User’s manual;

LIGHTING MODES

Turbo – maximum brightness level
High – high brightness level
Middle – medium brightness level
Low – low brightness level
Moon – minimum brightness level
Strobe – pulsating light with variable flicker frequency
Flash – a sub mode of each lighting mode (except strobe). Light with uniform flickering.

OPERATING INSTRUCTION

ON/OFF – press and hold the button for 0.5 seconds to turn on/ off the light.
Modes selection – with the light switched on, shortly click the button to cycle over the modes.
Flash – chose the desired brightness mode, then double click to turn on the flash light. Click to exit.
Strobe – with the light either switched on or off, press and hold the button for 3 seconds to enter the Strobe mode. Click to exit.
Lock/Unlock – with the light switched off, double click to lock the flashlight. Repeat the procedure to unlock.

Note. The flashlight automaticolly memorizes the lost selected lighting mode (excluding Strobe mode} and applies it next time when turned on.

BATTERY STATUS INDICATION

With the light switched off, click the button to see the battery status. The indication will last for 3 seconds. The battery status is also continuously displayed when the light is turned on.

4 divisions – s 100% of charge;
3 divisions – s 75% of charge;
2 divisions – s 50% of charge;
1 division – s 25% of charge;
1 division flashes – battery discharged. Recharge at the nearest opportunity.

CHARGING

Plug the USB-A socket of the charging cable into electrical outlet. Switch off the light. open the protective cover and connect the charging cable to the flashlight port. When charging, the indicator divisions will flash indicating the current charge level. When fully charged, all 4 divisions will turn on. After a full charge, unplug the charging cable and close the protective cover to prevent water and dust from entering the flashlight body.

The original batteries are supplied charged and can be used immediately after purchase, however it is recommended that the battery be fully charged before first use. The battery needs to be charged in time before it is completely discharged. During long periods of storage, it is recommended to keep the battery charging level at about half capacity to extend its service life.

BATTERY REPLACEMENT

Unscrew the tail lid of the flashlight counterclockwise;
Insert the battery with the ( +) contact towards the head of the flashlight;
Screw the base all the way in and test the flashlight.

MAINTENANCE AND SAFETY INSTRUCTIONS

For extended storage, it is necessary to remove batteries from the flashlight;
Lock the flashlight to prevent accidental activation during storage or transportation;
It is recommended that the rubber seals/gaskets and threaded parts of the flashlight be lubricated regularly to prevent premature wear and to maintain a proper water resistance. If the rubber rings are damaged, they must be replaced;
Keep battery contacts clean to maintain original performance. Dirty contacts can cause flickering, erratic shine, or even failure.

ATTENTION. Avoid direct light into the eyes, as this may lead to eyes injury; , During use, the flashlight can accumulate a significant amount of heat. which can cause the housing to heat up. Therefore be careful to avoid burns;

It is forbidden to shine a flashlight in critical proximity to flammable substances to avoid a fire;
Do not use batteries types other than those specified in technical parameters;
Do not disassemble the flashlight head, as this may impair performance and void the warranty.
Keep out of the reach of children.

WARRANTY

The warranty for the flashlight is 3 years, for the battery – 1 year. The warranty does not cover accessories. The LED source inside the flashlight is not replaceable. If the LED fails, the whole flashlight should be replaced. During the warranty period, a faulty flashlight and battery can exchanged or returned with prove of purchase and all accessories saved. The following does not apply with the scope of limited warranty:

Misuse the product and cause the products integral components damage;
Unauthorized disassemble or the presence of deep mechanical damage to the product;
Damage due to force majeure.

ENVIRONMENTAL PROTECTION

Pursuant to the provisions of the WEEE Act. it is forbidden to put waste equipment marked with the symbol of a crossed bin together with other waste. The user, wishing to get rid of electronic and electrical equipment. is obliged to return it to a waste equipment collection point. There are no hazardous components in the equipment that have a particularly negative impact on the environment and human health. The producer shall not be responsible for any damage resulting from the failure to follow above instructions. The manufacturer reserves the right to make changes to these user manual or technical changes to the product without prior notice.