BOSTON EHW094 Industrial Hose Instruction Manual
- June 13, 2024
- BOSTON
Table of Contents
BOSTON EHW094 Industrial Hose Instruction Manual
Assembly Instructions
To Assemble
Step 1
Cut hose to required length with a sharp knife. Oil inside of hose and
outside of SOCKETLESS nipple liberally
Step 2
Push hose on fitting until hose end bottoms underneath protective cap as
shown. For quantity production use a SOCKETLESS fitting assembly machine
To Disassemble
Step 1
Slit hose lengthwise from protective cap to end of nipple.
Step 2
Bend hose, then snap hose off with a quick tug
SOCKETLESS fittings
Low pressure service
Clamp location on hose fitting
CLAMP INFORMATION for SOCKETLESS, FD83 and UDQ connectors
Dash size| Part number| Reference| Ear width| Band
width| Size range
---|---|---|---|---|---
| | | mm (Inch)| mm (Inch)| mm (Inch)
-04| 16702998| 016.0-706R| 8.0 (0.315)| 7.0(0.276)| 13.5- 16.0(0.53- 0.63)
-06| 16402498| 019.8-706R| 10.0 (0.394)| 7.0(0.276)| 16.6- 19.8(0.65- 0.78)
-08| 16700029| 024.1-706R| 10.0 (0.394)| 7.0(0.276)| 20.9- 24.1(0.82- 0.95)
-10| 16700033| 027.1-706R| 10.0 (0.394)| 7.0(0.276)| 23.9- 27.1(0.94- 1.07)
-12| 16700040| 031.6-706R| 10.0 (0.394)| 7.0(0.276)| 28.4- 31.6(1.12- 1.24)
-16| 16700052| 039.6-706R| 10.0 (0.394)| 7.0(0.276)| 36.4- 39.6(1.43- 1.56)
The use of clamp is dependent on the performance parameters of hose.
Please refer to hose pressure ratings for when clamp is required.
To Assemble
Step 1
Cut hose to required length with a sharp knife. Oil inside of hose and
outside nipple liberally
Step 2
Push hose on coupling hose barb until hose end touches the flat surface of
the coupling body.
To Disassemble
Step 1
Slit hose lengthwise from edge of coupling body to end of the barb.
Step 2
Bend hose, then snap hose off with a quick tug.
FD83 series
Full-flow dual-interlock coupling
Universal Quick Disconnect (UQD)
For thermal management applications
Clamp location on hose fitting
Clamp location on hose fitting
Any information, including, but not limited to information on selection of product, its application or use, product design, weight, dimensions, capacity or any other technical data in product manuals, catalogues descriptions, advertisements, etc. and whether made available in writing, orally, electronically, online or via download, shall be considered informative, and is only binding if and to the extent, explicit reference is made in a quotation or order confirmation. Danfoss cannot accept any responsibility for possible errors in catalogues, brochures, videos and other material. Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without changes to form, fit or function of the product. All trademarks in this material are property of Danfoss A/S or Danfoss group companies. Danfoss and the Danfoss logo are trademarks of Danfoss A/S. All rights reserved.
Danfoss Power Solutions, Nordborgvej 81, 6430 Nordborg, Denmark,
Tel. +45 74 88 22 22,
Fax +45 74 65 25 80
www.danfoss.com,
E-mail: [email protected]