Boston Rectangular Dark Oak Mirror with Shelf User Manual
- October 30, 2023
- BOSTON
Table of Contents
Rectangular Dark Oak Mirror with Shelf
Austin Range Bathroom Furniture Fitting Guide
Before installing the product, please ensure you have the following tools:
- Suitable fixings for securing the unit to the wall (pre-drilled holes provided in back panel of unit)
- Screwdriver
- Measuring tape
- Silicone
Hinge Adjustment
Loosen screw ‘A’ on all hinges, adjust door and retighten screw for
vertical adjustment. For lateral adjustment, loosen screw ‘B’, adjust door and
retighten screw. For horizontal adjustment, follow step ‘C’ to adjust the
screw.
Drawers Remove/Install
To remove the drawer, follow step ‘A’ and remove the fastener, then follow
step ‘B’. To install the drawer, follow step ‘B’ and then follow step ‘A’ to
lock the fastener. If drawer position needs altering, follow step ‘C’ to
adjust the screw.
Wall Hung Unit Installation
Please measure the ‘L’ distance between each bracket on the unit and the
‘H’ height as requested by the customer. The standard height is 850mm
(including basin height) from floor to wash basin. Use suitable fixings
provided in the box to secure the unit to the wall.
Mirror Cabinet and Storage Unit Installation
Please measure the ‘L’ and ‘H’ distance between each pre-drilled hole on
the product and fix them using the plug screws with chrome covers provided in
the box. The distance between the mirror cabinet and basin should be
300-400mm. The distance from floor to the bottom of the storage unit should be
as requested by the customer.
AUSTIN RANGE BATHROOM FURNITURE FITTING GUIDE
Tools required for installations
Note: For safety reasons Unit must be secured to the wall using suitable
fixings (pre-drilled holes provide in back panel of unit)
When fitting a basin to a unit, a bead of silicone should be applied to the
top edge of the basin unit to seal between the basin and unit.
Please spend 5 minutes reading this section before commencing with the installation of your new furniture.
- Should any of your items have a defect, please do NOT install as returns will not be accepted once fitted.
- We advise that you use a qualified person to install your units, as any issues relating to poor fitting will not be accepted by the supplier.
- You have purchased a handmade and in some cases hand painted product. Therefore, you may see some slight imperfections which the supplier may deem as acceptable.
- This product is water resistant but NOT waterproof. On no account should any spillages or splashes, even water, be allowed to lie on any surface. All spillages and splashes should be wiped dry, failure to do so may shorten the life expectancy of the product and invalidate any guarantees.
- Please avoid direct sunlight as this will cause the painted surfaces to discolor.
- Due to motion in transit, the cabinet doors and drawers may need to be adjusted after installation.
- Floor Standing units must be fitted back to the wall through the backtrail using suitable fixings. (not supplied)
- Basin units should be fitted as above. The basin should also be secured where applicable using Fischer bolts through the fixing points under the basin. (not supplied) Note that not all basins have this facility.
- Wall Hung units must be secured back to the wall using the wall hanging brackets or suitable wall fixings when not supplied. Additional support is recommended using ‘L’ brackets. (not supplied)
- When fixing to a stud or paneled wall, appropriate frame work should be installed to support the basins and units.
- Where units or worktops have to be cut-out for services, all raw edges MUST be sealed against water ingress.
Hinge Adjustment
Drawers Remove/Install
To Remove the Drawer: Follow step ‘A’ and remove the fastener then follow step
‘B’. To Install the Drawer: Follow step ‘B’ and then follow step ‘A’ to lock
the fastener. Drawer position: If drawer position needs altering follow step
‘C’ to adjust the screw. 
BATHROOM FURNITURE CUSTOMER CARE GUIDE
Please note that although these units have been designed to give years of pleasure and satisfaction, you will help maintain the original beauty of your bathroom by following these guide lines.
Melamine, Vinyl and Foil Wrapped Doors
Occasional marks, can in most cases, be removed with a soft damp cloth. More
persistent marks can
be removed using a non silicone based furniture cleaner. Hot soapy water
should be avoided. Once
the mark is removed, the area should be wiped over with a damp cloth to remove
any excess and dried with a soft clean cloth. On no account should solvent or
an abrasive cleaner be used as permanent damage to the finish could take
place.
High Gloss Doors
Use a cleaning product not containing aggressive substances like acetone,
alcohol, bleach … as those components could seriously damage the surface of
the door. The best would be to use a soft cotton or micro fibre cloth with
only water and soft soap (containing a maximum 1% of liquid soap)
Carcase Components
Do not use polish on any surfaces. A damp cloth with soapy water will clean
off most marks or spills. Bleaches, scouring pads and multi-surface cleaners
should not be used.
Drawers, Runners, Door Hinges
These should be wiped out with a damp soapy cloth and wiped dry with a soft
cloth as necessary. The roller runners and hinges are lubricated and should
not be cleaned with a degreasing agent as this will affect the action of the
moving parts. Never lean on partially or fully opened doors and drawers in
order to gain access to the units. The hinges are specified to adequately
support the weight of the door, plus small additional weights such as wire
accessories. It is advised that once the bathroom has been installed you
should check every six months that all screws on the hinges are tight.
Worktops
Although the worktop is hard wearing, sharp objects will scratch and excessive
heat will scorch the surface. Care should be taken not to drop any heavy
objects onto the worktop as the surface may crack.
For cleaning, a damp soapy cloth will clean off most spills. Bleaches,
scouring pads and multi-surface cleaners should not be used. Corrosive liquids
and make-up should be wiped off immeadiately. On no account should any
spillage, even water, be allowed to lie on the surface.
Temperature and Humidity
Avoid excessive change in temperature and humidity. Always try to ensure
adequate ventilation.
General care, spillages and splashes
On no account should any spillages or splashes, even water, be allowed to lie
on any surface.
All spillages and splashes should be wiped dry, failure to do so may shorten
the life expectancy of the product and invalidate any guarantees.
Wall hung unit installation.( fixings in box)
Please measure the L distance between each brackets on unit. and H ( height as
customers request. The standard height is 850mm (including basin height) from
floor to wash basin
Mirror cabinet and Storage unit. ( plug screws with chrome covers in box)
Please measure the L&H distance between each pre-drilled holes on products and
fixing them as below steps the distance will be 300-400 the mirror cabinet to
basin as below . the distance from floor to bottom of storage as customer
requests.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>