Boston EHW194 Hose Assembly Instruction Manual

Boston EHW194 Hose Assembly

Product Information

Specifications:

• Compatible with Boston EHW194 and EHW094 hose
• Socketless, FD83, and UQD connectors
• Low-pressure service for SOCKETLESS fittings

Product Usage Instructions

Fitting Assembly with Boston EHW194 and EHW094 Hose

Hose Assembly Instructions

Socketless, FD83, and UQD Connectors
To Assemble:

1. Cut the hose to the required length with a sharp knife. The oil inside of the hose and outside of the SOCKETLESS nipple liberally.
2. Push hose on fitting until hose end bottoms underneath protective cap as shown. For quantity production, use a SOCKETLESS fitting assembly machine.

SOCKETLESS Fittings
Low-pressure service

To Disassemble:

1. Slit the hose lengthwise from the protective cap to the end of the nipple.
2. Bend the hose, then snap the hose off with a quick tug.

Clamp Location on Hose Fitting

CLAMP INFORMATION for SOCKETLESS, FD83, and UQD
Connectors:

Dash Size| Part Number| Ear Width mm (Inch)| Band Width mm (Inch)| Size Range mm (Inch)
---|---|---|---|---
-04| FF91764-162| 8.0 (0.315)| 7.0 (0.276)| 13.5 – 16.0 (0.53 – 0.63)

FD83 and UQD Series Hose Assembly Instructions for Quick
Disconnect Coupling with Boston EHW094 & EHW194 Hose
To Assemble:

1. Cut the hose to the required length with a sharp knife. The oil inside of the hose and outside nipple liberally.
2. Push the hose on the coupling hose barb until the hose end touches the flat surface of the coupling body.

FD83 Series
Full-flow dual-interlock coupling

To Disassemble:

1. Slit the hose lengthwise from the edge of the coupling body to the end of the barb.
2. Bend the hose, then snap the hose off with a quick tug.

Universal Quick Disconnect (UQD)
For thermal management applications

Clamp Location on Hose Fitting
Danfoss Power Solutions, Nordborgvej 81, 6430 Nordborg, Denmark, Tel. +45 74 88 22 22, Fax +45 74 65 25 80 www.danfoss.com, E-mail: info@danfoss.com AN460864287876en-000102

FAQs

• Q: When should I use a clamp with the hose fittings?
  A: The use of a clamp is dependent on the performance parameters of the hose. Please refer to hose pressure ratings to determine when a clamp is required.

Boston-EHW194-Hose-Assembly-product

Hose assembly instructions

Socketless, FD83, and UQD connectors
SOCKETLESS® fittings with Boston® EHW094 and EHW194 hose

To Assemble

• Step 1
  Cut the hose to the required length with a sharp knife. The oil inside of the hose and outside of the SOCKETLESS nipple liberally.

• Step 2
  Push hose on fitting until hose end bottoms underneath protective cap as shown. For quantity production use a SOCKETLESS fitting assembly machine.

To Disassemble

• Step 1
  Slit the hose lengthwise from the protective cap to the end of the nipple.

• Step 2
  Bend hose, then snap the hose off with a quick tug.

SOCKETLESS fittings

Low-pressure service

CLAMP INFORMATION

for SOCKETLESS, FD83 and UQD connectors

The use of a clamp is dependent on the performance parameters of the hose. Please refer to hose pressure ratings for when a clamp is required.

FD83 and UQD Series hose assembly instructions
for quick disconnect coupling with Boston EHW094 & EHW194 hose

To Assemble

• Step 1
  Cut the hose to the required length with a sharp knife. The oil inside of the hose and outside nipple liberally.

• Step 2
  Push the hose on the coupling hose barb until the hose end touches the flat surface of the coupling body.

To Disassemble

• Step 1
  Slit the hose lengthwise from the edge of the coupling body to the end of the barb.

• Step 2
  Bend the hose, then snap the hose off with a quick tug.

Danfoss Power Solutions, Nordborgvej 81, 6430 Nordborg, Denmark, Tel. +45 74 88 22 22, Fax +45 74 65 25 80
www.danfoss.com, E-mail: info@danfoss.com
Any information, including, but not limited to information on the selection of product, its application or use, product design, weight, dimensions, capacity or any other technical data in product manuals, catalogs descriptions, advertisements, etc., and whether made available in writing, orally, electronically, online or via download, shall be considered informative and is only binding if and to the extent, explicit reference is made in a quotation or order confirmation. Danfoss cannot accept any responsibility for possible errors in catalogs, brochures, videos, and other material. Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without changes to the form, fit or function of the product. All trademarks in this material are property of Danfoss A/S or Danfoss group companies. Danfoss and the Danfoss logo are trademarks of Danfoss A/S. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>