REPOTEC 18-36VAC Industrial Media Converter User Manual
- June 13, 2024
- REPOTEC
Table of Contents
- REPOTEC 18-36VAC Industrial Media Converter User Manual
- User Manual
- FCC MARKING
- CE MARKING
- Trademarks:
- Key Features
- Installation package
- Power connection
- WARNING — Always SHUT OFF power source to connect power wire.
- Dip switch function
- LED indicator
- Specification
- Housing Dimension (mm)
- NOTE:
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
REPOTEC 18-36VAC Industrial Media Converter User Manual
User Manual
Industrial Media Converter, with 1 x 100BaseF(X) SC SM 30KM + 1 x 10/100M, 18-36VAC or 12-56 VDC input
FCC MARKING
This Equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55032/35 class A for ITE, the essential protection
requirement of Council Directive 2014/30/EC on the approximation of the laws
of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check
with your local distributors for the latest information. No part of this
document can be copied or reproduced in any form without written consent from
the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Key Features
- True Mini, hardened design enclosure 59x36x50mm (LxWxD)
- Supports 18V-36VAC, 12V-60VDC or DC Jack socket
- Supports Link Fault Pass through (LFP) function
- Supports Switch Mode and Converter
- Surge protection diodes on power
- ESD protection diodes on RJ-45 port
- Provides Far End Fault function on FX
- Provides increased Noise Immunity
- Extended environmental specification -40°C to 75°C
Installation package
This unit can be din-rail mounted or wall-mounted. Din-rail brackets and wall-
mount brackets are included.
Power connection
This unit provides a 3 pin terminal block. It can be operated using either VAC
or VDC power sources. The VDC power range is from 12VDC to 60VDC, and the VAC
power range is from 18VAC to 36VAC. Always make sure your input voltage is
within this supported voltage range.
To connect power: Follow the printed polarity for V+, V- and Ground.
Connect positive wire to V+, connect negative wire to V- and also connect
neutral wire to ground.
Power connecting procedure:
STEP 1 – Pull out 3 pin terminal block.
STEP 2 – Connect wire to V+, V- and Ground.
STEP 3 – Connect SC/SFP/WDM fiber wire to fiber port. STEP 4 – Plug back 3 pin
terminal block to its place.
WARNING — Always SHUT OFF power source to connect power wire.
WARNING – DO NOT force SFP fiber into SFP housing without removing terminal block. WARNING — Any exceeded input voltage will not make this unit function and may damage this unit.
Dip switch function
**** This unit is equipped with dip switches, located on the front panel
marked as SW1. Adjusting the dip switches will change the default function of
this unit. This unit has set to manufacturer default as: Switch Mode ON and
LFP function OFF.
The table shown as you may change the dip switch setting to your desired
environment
LED indicator
Specification
IEEE Standard
| IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3u 100Base-FX Fast Ethernet
IEEE802.3x Flow Control and Back Pressure
---|---
Data Processing| Store and Forward
Flow Control| IEEE 802.3x Flow Control and Back Pressure
Jumbo Frame| 9KB
Architecture
| Full wire speed conversion,
Transparent conversion to 802.1Q VLAN tagged packets.
Network Connector
| 1 x RJ-45 10/100BaseT(X) Auto negotiation, Auto MDI/MDI-X function, Full/Half duplex
1 x 100M SC Single-Mode 30km
LED Indicators
| PWR(Green): ON-Power is detected LK/Act (Green): ON-Fiber is detected
Flashing-Data is transmitting/receiving
RJ-45 port
Green: ON-TX link is detected
Flashing-TX data is transmitting/receiving Amber: ON-100M speed is detected
OFF-10M speed is detected
DIP Switch
| DIP1: UP-LFP enable
DOWN-LFP disable (Default) LFP (Link Fault Pass Through)
DIP2: UP-Converter Mode
DOWN- Switch Mode (Default)
Power Protection| Surge protection diodes on power input
Connector Protection| ESD protection diodes on TX port
Reserve Polarity Protection| Present
Overload Current Protection| Present
Power Input
| 18V-36VAC, 12V-60VDC,
DC Jack terminal cable supported (DC Barrel Connector)
Conformance to UL Standards| Use Isolated power supply to conform with UL 508
standard
---|---
Power Consumption| Full Load: 1.92Watts at 48VDC
Removable Terminal Block
| 3 pin contact terminal block for power input Wire range: 0.34mm^2 to 2.5mm^2
Solid wire (AWG):12-24/14-22 Stranded wire (AWG): 12-24/14-22 Torque:5lb- In/0.5Nm/0.56Nm
Wire Strip length: 7-8mm
Operating Temperature| -40°C~75°C
Operating Humidity| 5% to 95% (Non-condensing)
Storage Temperature| -40°C~85°C
Housing Design| IP40 Design, high graded Aluminum
Case Dimension (L X W X D)| 59 x 36 x 50 mm (L x W x D)
Installation| DIN-Rail mounted, Panel Mounted
Certifications
Safety| LVD (EN62368-1)
EMC/EMS| CE, FCC, EN55032/35, VCCI
EMI| FCC Part 15 Subpart B Class A
Vibration| EN 60068-2-6
Shock| EN 60068-2-27
Free Fall| EN 60068-2-32
Housing Dimension (mm)
NOTE:
Housing dimension is for the purpose of showing product Length, Width, Height, din-rail, and terminal block’s position and dimension. Please reference the LED Indicator Page for correct port order.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>