REPOTEC 02-RP-IPG816 Industrial PoE Switch User Manual
- June 13, 2024
- REPOTEC
Table of Contents
REPOTEC 02-RP-IPG816 Industrial PoE Switch
Product Information
| Section | Content |
|---|---|
| FCC MARKING | This equipment complies with the requirements relating to |
electromagnetic compatibility, EN 55032/35 class A for ITE, the
essential protection requirement of Council Directive 2014/30/EU on
the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company Policy| Company has an on-going policy of upgrading its products and
it
may be possible that information in this document is not
up-to-date. Please check with your local distributors for the
latest information. No part of this document can be copied or
reproduced in any form without written consent from the
company.
Trademarks| All trade names and trademarks are the properties of their
respective companies.
Introduction| The product is introduced in this section.
Installation package| This unit can be wall mounted or din-rail mounted. Wall
mount
brackets and din-rail bracket are included.
Power connection| This section provides information about the power connecting
procedure.
LED indicator| This section explains the meaning of different LED indicators
on the product.
Specification| This section provides detailed specifications of the product
including IEEE Standard, Switch Architecture, Data Processing, Flow
Control, Jumbo Frame, MAC address Table Size, Packet Buffer Size,
Network Connector, Network Cable Protocol, LED, Reserve Polarity
Protection, Overload Current Protection, Power Supply, Power
Consumption, Alarm Relay Contact, PoE Power, Removable Terminal
Block, Operating Temperature, Operating Humidity, Storage
Temperature, MTBF (mean time between failure), Housing Case
Dimension, Installation.
Certifications| This section lists the safety and EMC certifications the
product has obtained.
Product Usage Instructions
- Follow the installation package instructions to mount the unit on a wall or din-rail.
- Connect the power following the provided power connecting procedure.
- Observe the LED indicators to understand the status of different connections and ports:
- P1(Green): ON – P1+, P1- is connected
- P2(Green): ON – P2+, P2- is connected
- P3(Amber): ON – P3 is connected via Power DIN
- RLY(Amber): ON – Only PW1 or PW2 is connected; OFF – both PW1 and PW2 are connected
- LNK(Green): ON – TX port is detected; OFF – TX port is not detected; Flashing – TX port is active
- PoE(Amber): ON – PD is detected on designated port.
- Refer to the specification section for detailed information on the product’s IEEE Standard, Switch Architecture, Data Processing, Flow Control, Jumbo Frame, MAC address Table Size, Packet Buffer Size, Network Connector, Network Cable Protocol, LED, Reserve Polarity Protection, Overload Current Protection, Power Supply, Power Consumption, Alarm Relay Contact, PoE Power, Removable Terminal Block, Operating Temperature, Operating Humidity, Storage Temperature, MTBF (mean time between failure),Housing Case Dimension, and Installation.
- Ensure the product has obtained the necessary safety and EMC certifications listed in the Certifications section.
User manual
Hardened Industrial 16 port Gigabit PoE Switch, 16 x 10/100/1000 TX 30W
PSE,48-56VDC input voltage, operating temp.: -40°C to +75°C
FCC MARKING
This Equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55032/35 class A for ITE, the essential protection
requirement of Council Directive 2014/30/EU on the approximation of the laws
of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check
with your local distributors for the latest information. No part of this
document can be copied or reproduced in any form without written consent from
the company.
Introduction
This Industrial PoE switch is designed with Hardened Ethernet controller and Hardened PoE controller to ensure performance in harsh environment. It is equipped with 16 ports 30Watts Giga TX PSE and can deliver up to 300Watts of power to your PD devices. All ports are independent, with a total of 16 ports for easy expansion of your network application. With our Cold-Design technology, it will not only power up your PD but also reduce its excessive heat to a minimum. It has been rigorously tested for your security, surveillance, and telco applications.
Installation package
This unit can be wall mounted or din-rail mounted. Wall mount brackets and din-rail bracket are included
Power connection
This unit provides a 6 pin terminal block. PoE functions can be operated from 48-56VDC power input. Always make sure your input voltage is within this supported voltage range for each model.
WARNING – any exceeded input voltage will not make this unit function and
may damage this unit.
This unit comes with 3 power input sources. P1, P2, and P3.
- To connect power: Follow the printed polarity for P1+, P1-, P2+, P2-, and ground. Connect positive wires to P1+ and/or P2+, connect negative wires to P1- and/or P2-, and connect the neutral wire to the ground screw as shown.
- Power DIN: This unit contains an extra P3 port for power DIN. This power DIN can power the unit via external power adapter.
- Relay: This unit includes an additional 24V@1A relay circuit for special purpose. When 2 powers are connected, the relay is in OPEN mode. If only one of the power sources is connected, the relay changes to SHORT mode. This relay will only work with P1 and P2. It is independent from P3.
Power connecting procedure
STEP 1 – Pull out 6 pin terminal block.
STEP 2 – Connect wire to P1+, P1-, P2+, P2-, and the neutral wire to the ground screw.
STEP 3 – Plug connected 6 pin terminal block back into place.
Or, Connect the P3 power DIN from external power adapter.
WARNING — Always SHUT OFF power source to connect power wire.
WARNING — Always ground the power source to maintain a clean power input. Cheaply made power supplies create too much noise and will cause the power input to fluctuate when connected to this unit. To avoid this, always ground the power source to maintain a clean power input.
LED indicator
Specification
IEEE Standard
| IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3x Flow Control and Back Pressure IEEE 802.3af PoE
IEEE 802.3at PoE+
---|---
Switch Architecture| Back-plane (Switching Fabric): 32Gbps
Data Processing| Store and Forward
Flow Control| IEEE 802.3x Flow Control and Back Pressure
Jumbo Frame| 9KB
MAC address Table Size| 8K
Packet Buffer Size| 4.1Mbits
Network Connector
| 16 x RJ-45 10/100/1000BaseT(X) auto negotiation Auto MDI/MDI-X function, Full/Half duplex
16 x Gigabit PoE+ 802.3at/af PSE port, 30W per port
Network Cable| UTP/STP Cat.5e or above Cable
EIA/TIA-568 (100m)
Protocol| CSMA/CD
LED
| PW1 (Green): ON－Power 1 is detected PW2 (Green): ON－Power 2 is detected
PW3 (Amber): ON－Power 3 is connected via Power DIN RLY (Amber): ON－Only PW1 or PW2 is connected
OFF－Both PW1 and PW2 are connected
TX/RJ-45 port:
LNK (Link/Active) (Green): ON－TX port is detected
Flashing－TX data is transmitting/receiving
PoE (Amber): ON－PD is detected and PSE is activated
OFF－PD is not detected
Reserve Polarity Protection| Present
Overload Current Protection| Present
Power Supply| Redundant Dual DC 48V-56V Power Input
Power Consumption| 12.9W@48 VDC full load, Without PoE
Alarm Relay Contact
| Relay outputs with current carrying capacity of 1 A @24VDC, Relay in open circuit mode when 2 powers are connected. in
short circuit mode when only one power supply is connected
PoE Power
| PoE power per port 30watts.
Maximum total power 300Watts with 56VDC input, Supports IEEE 802.3af/at
---|---
Removable Terminal Block
| Provide 2 Redundant power , Alarm relay contact ,6 Pin Wire range: 0.34mm^2 to 2.5mm^2
Solid wire (AWG):12-24/14-22 Stranded wire(AWG): 12-24/14-22 Torque:5lb- In/0.5Nm/0.56Nm
Wire Strip length: 7-8mm
Operating Temperature| -40°C to 75°C
Operating Humidity| 5% to 95% (Non-condensing)
Storage Temperature| -40°C to 85°C
MTBF (mean time between
failure)
| ****
449,232 hrs (Telcordia (Bellcore), GB) at 50°C
Housing| Rugged Metal, IP30 Protection
Case Dimension| 155 x 48 x 120 mm (LxWxD)
Installation| DIN Rail Mount or Wall Mount
Certifications:
Safety| UL 60950-1
Safety| LVD (EN 62368-1)
EMC| CE, FCC, EN55032/35, VCCI
EMI| CISPR 32, FCC Part 15 Subpart B Class A
EMS
| IEC 61000-4-2 ESD: Contact: 6KV; Air: 8KV IEC 61000-4-4 EFT: Power: 2KV; Signal: 2KV
IEC 61000-4-5 Surge: Power: 2KV; Signal: 2KV
Vibration| EN 60068-2-6
Shock| EN 60068-2-27
Free Fall| EN 60068-2-32
Housing Dimension (mm)
Trademarks:
All trade names and trademarks are the properties of their respective
companies.
Copyright © 2022, All Rights Reserved.