10 20 30 Reef Factory Smart wave User Guide

10 20 30 Reef Factory Smart wave

Languages

• PL
• EN
• DE
• FR

For more information, visit: www.reeffactory.com/support

Specifications

Max. temperature

of the aquarium water:

| +35°C
Operating temp./ humidity:| 0°C -35°C / max 90%
Power:| , ow| 20W| 30W
Input:| 1DD-240VAC 50-60Hz (AC-DC adapter included)
Radio protocol:| Wi-Fi(802.11 b/g/n)2400.0-2483.5MHz,max EIRP +20dBm
Circulator dimensions[mm] (W x D x HI:| 61x46x61| 73x56x73| 78x62x78
Performance [1/h]:| 4000| 10000| 13000
Water resistance of the circulator:| IPX8
This device contains an RF Module:
•  Part number:| ESP32C3MINl1
•  FCCID :| 2AC7Z-ESPC3MI N11

Ta download the full manual, scan the OR code on the first pages, or visit our website: www.reeffactory.com/smartwave.

WiFi Reset

1. Press and hold the reset button for 10 seconds.
2. Wait for the display to show “rEt”.
3. Click the button once to confirm.

Reset

1. Press and hold the reset button for 15 seconds.
2. Wait for the display to show “rES”.
3. Click the button once to confirm.

FAQs

How do I reset the WiFi on my Smart Wave device?

  Press and hold the reset button for 10 seconds until the display shows “rEt”, then click the button once to confirm.

What should I do if my Smart Wave device is not working?

  Ensure it is properly plugged in and the power source is functioning. If the problem persists, refer to the troubleshooting section in the full user manual available at [www.reeffactory.com](https://www.reeffactory.com/).

Where can I find the full user manual?

  The full user manual is available online at [www.reeffactory.com](https://www.reeffactory.com/).

WHAT IN THE BOX

INSTALLATION

Full user manual

Important safety information

Read this manual carefully before installing and operating the product.

• The manufacturer will not be held responsible for any loss or damage resulting from not following the instructions. Store this manual in a secure place for future reference.
• This product is not a toy. Keep away from children.

Read the product diagram (SI at the beginning of this manual

1. Main unit
2. Power supply
3. Controller
4. OIN mounting rail
5. Mounting magnet
6. Angle mount magnet cap
7. Mounting magnet

Installation of the device

• After unpacking the components from the packaging, follow the assembly steps shown in the graphic.  To mount the controller with a dedicated DIN rail, follow the (Ml graphic. The kit does not include screws, which must be selected independently depending on the substrate.

Initial setup

1. Open the Smart Reef app or log in to your account at www.reeHactory.com.
2. Click on the “add device” button in the lower right corner of the screen.
3. Follow the messages on the screen.

Legal information

WEEE Directive Compliance

• Devices labeled with this symbol should not be disposed of with other household wastes. It shall be handed over to the applicable collection point for the recycling of waste electrical and electronic equipment.

Declaration of conformity

• Hereby, Reef Factory Sp. z o.o. declares that the device complies with the essential requirements and other relevant provisions of Directives 2014/53/EU, 2011/65/EU, and 2015/863. The full text of the EU Declaration of Conformity is available at the following internet address: www.reeffactory.com.

Caution

• Do not attempt to disassemble, repair, or modify this product yourself.
  Any repair should be performed only by an authorized Reef Factory service.

• This product is designed for indoor use only. Do not use it outside!

• Do not expose the controller and power supply to water or other liquids unless the instructions say otherwise.

• Do not use the product outside of the recommended temperature and humidity ranges.

• Keep the product away from heat sources and do not place it under direct sunlight.

• Do not cover or place anything on the product.

• Do not connect cables other than those included with the device or specified in the manual.

• Do not place the product in metal boxes or on metal surfaces for best radio performance.

• Do not use aggressive detergents to clean the device. Clean mechanically with a soft cloth.

Manual edition 1.1, January 2024.

• IS0015
• Model: RFRFS, RFRFM, RFRFL

Notice :

• Due to continuous technical improvements and system updates, the information contained in this manual is subject to change without prior notification to users. The photographs and illustrations contained in this manual are for informational purposes only and may differ slightly from the actual product.

CONTACT INFORMATION

• Reef Factory Sp. z o.o.
• Bydgoska 94, 86-032 Niemcz, Poland
• www.reeffactory.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>