VANGUARD ALTA PRO 2 Aluminum-Alloy Tripod Kit User Manual
- June 9, 2024
- Vanguard
Table of Contents
ALTA PRO 2 Aluminum-Alloy Tripod Kit
User Manual
ALTA PRO 2 Aluminum-Alloy Tripod Kit
| 
---|---
| 
| 
Thank you for choosing VANGUARD’S ALTA PRO 2 tripod. ALTA PRO 2 is a sturdy tripod yet one of the lightest in its category. With exclusive features, ALTA PRO 2 is a unique tripod that provides great performance and stability for photo, video and sport optics. Available in aluminum, the series is offered with either 3 or 4 sections kit options including a 3-way Pan Head, 2-way Fluid Pan Head, Grip Head and Video Head. Enjoy imaging with Vanguard!
PART DESCRIPTION
A: Dual size 1 /4″- 3/8″ Head Screw Adapter
B: Set screws or Locking set screws
C: Anti-Shock Rubber Ring
D: Central Column
E : Central Column Locking Knob
F: Leg Angle Markings in angle of degrees
G: 3/8″ Accessory Link Thread
H: 3/8″ Accessory Link Cap
I: Leg Angle Adjusting Button
J: Rubber Grip Handle
K: Legs
L: Central column Stop Pin
M : Central Column Release Stop Button
N : Twist Lock / Unlock Icons
O: Twist Lock
P: Twist lock Hex Screws
Q : Rubber Feet
R: Spirit Level
S: Ring hole
T: Leg Angle Locking Bolt
CAMERA & HEAD SCREW ADAPTER
A hex wrench (included) can be used to attach or detach the camera head screw adapter “A”, screw counterclockwise to loosen, clockwise to tighten. The camera screw is a reversible 1 /4″ and 3/8″ dual size screw. Please choose either size according to your head thread type. Please make sure the camera screw is fully tightened before attaching the head.
CAMERA HEAD ATTACHMENT OR REMOVAL
Attaching the head:
Step 1) Make sure screw size (3/8″ or 1/4″) is chosen to match your
camera head.
Step 2) Move the anti-shock ring “C” down and make sure the 3 set screws
“B” are not interfering.
Step 3) Connect the tripod and head by turning the head clockwise until
tight.
Step 4) Use the hex wrench to tighten set screws “B” by turning
clockwise. Confirm the 3 set screws “B” are perfectly tightened before use of
your tripod kit
Removing the head:
Step 1) Move the anti-shock ring “C” down.
Step 2) Using the hex wrench, release set screws “B” by turning
counterclockwise.
Step 3) Make sure panning knob of head is locked, then turn the head
counterclockwise.
ANTI-SHOCK RUBBER RING
The Anti-shock rubber ring “C” protects your equipment from damage when the
central column “D” is lowered too quickly.
CENTRAL COLUMN ADJUSTMENT
The central column “D” can be elevated to reach the specific desired height
for your shoot. Release the central column lock knob “E” by turning
counterclockwise, adjust the height of the central column as required, lock
central column by turning “E” clockwise until it is fully tightened.
LEG ANGLE ADJUSTMENT
Push down leg angle adjustment button “I” (located on both sides of each leg)
to adjust legs to any of the four preset angles (20, 40, 60, and 80 degrees).
Legs can be adjusted individually for uneven terrain or set for customized
positioning.
OTIGHTENING A LOOSE LEG
If the leg becomes loose after using for a period of time, use a 4mrn alien
key to tighten the leg angle locking bolt “T” until the desired tension is
obtained. Turn it clockwise to tighten, counterclockwise to loosen.
LEG ANGLE ADJUSTMENT
To adjust the height of each leg, release the twist lock “O” and extend or
retract the telescopic leg to the desired length. Begin at the top and work
your way down to obtain desired height . Extending & using the larger leg
section first will make your tripod more stable (as shown in figure 8).
Step 1) Open the legs.
Step 2) Release the leg sections successively by unlocking “O”, the
Advanced twist-lock 1/4 turn locklunlock system. Turn clockwise 1/4 turn until
the unlock icon “N” is aligned with the twist lock line mark then extend leg
section.
Step 3) Lock “O” by turning counterclockwise until the lock icon “N” is
aligned with the twist lock line mark and make sure it is fully tightened.
When tightening it is not uncommon to sometimes pass the mark for locking the
tripod leg.
Step 4) Proceed the same way for the two other legs and make sure all
locks “0” are tightened to avoid an unstable tripod or equipment damage.
The tripod can be set in a leveled position thanks to the spirit level “R”
positioned on the side of the top spider casting/canopy.
PLEASE USE THE HAND GRIP POSITION ON LEGS (AS SHOWN IN FIGURE 10) TO
OPERATE YOUR TRIPOD.
RUBBER FEET TO SPIKED FEET
ALTA PRO 2 tripod is fitted with Multi Angle Rubber feet on the legs and can
accommodate spiked feet (sold separately) if desired.
Note: If putting rubber feet back on to legs attach rubber feet as shown
in directions (as shown in figure 11).
ALTA LINK
The ALTA PRO 2 tripod is fitted with a 3/8″ thread on the side of the top
spider cast/canopy which can be used to attach arms for monitors and other
accessories. Pull out “H” screw cap attach arm or other accessories that have
a 3/8″ connector.
TRANSPORT & STABILITY OF THE TRIPOD IN OUTDOOR SITUATION
ALTA PRO 2 is fitted with a hook attachment “S” on the central column which
can be used to attach a shoulder strap (not included) for easy transport of
the tripod. Windy conditions ? The hook attachment “S” is useful for holding a
counterweight ensuring your tripod is more stable.
Attention: Please handle with care to avoid hurting or pinching yourself
while working with the tripod.
Notes before use:
-
Following the set-up of the tripod, confirm all legs are spread open and locked before mounting your camera. Failure to do so may cause the tripod to fall and your equipment to he damaged.
-
Always comply with the weight restrictions. Going over the maximum load capacity may cause damage to equipment or personal injury.
-
Ensure all individual knobs and locks are tight to avoid movement, as movement may result in equipment damage or personal injury.
-
Carefully hold camera equipment stable when removing it from the tripod.
-
Carrying your tripod:
a) After use, remove the camera; fold the tripod completely; and ensure the tripod handle faces out when folding.
b) DO NOT carry the tripod when the camera is still mounted. -
Cleaning your tripod:
a) When necessary, wipe tripod with a soft cloth and if required use a mild detergent.
b) When used around salt water, first flush with fresh water, then wipe with a dry soft cloth.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>