REPOTEC RP-EC500CK IP PoE Extender User Manual

June 13, 2024
REPOTEC

IP/ PoE Extender
User Manual
Model : RP-EC500CK
Ethernet over Coaxial Extender

REPOTEC RP-EC500CK IP PoE Extender

Introduction

RP-EC500CK is an IP extender that can use a single coaxial cable to send TCP/IP signal to a remote IP-enabled device, with transmission distance up to 800M and bandwidth up to 100Mbps.
Furthermore, since RP-EC500CK can send IP signal over a coaxial cable, you can change your old analog cameras to IP ones without replacing existing cables, which saves a plenty of labor and cost.

Features

  • Sends IP signal over coaxial cable.
  • Signal extension up to 800M over a RG59/6U coaxial cable
  • Bandwidth up to 70Mbps.
  • Able to send multiple IP signals over single Ethernet cable

Transmission Distance Chart

The transmission distance test report below is by means of using the COMMSCOPE 57535-2 (CAT5e 24AWG) cables and 75Ω RG59 or RG6U coaxial cables.

Port / Cable Mode and Data Rate Distance
RJ45 – CAT.5e 100BASE-TX with EEE 100Mbps 100M
RJ45 – CAT.5e 100BASE-TX 100Mbps 130M
RJ45 – CAT.5e 100BASE-T1 100Mbps 300M
RJ45 – CAT.5e Long Reach 100Mbps 500M
RJ45 – CAT.5e 10BASE-T with EEE 10Mbps 100M
RJ45 – CAT.5e 10BASE-T 10Mbps 250M
RJ45 – CAT.5e Long Reach 10Mbps 800M
BNC – RG59 (75-3) 100Mbps 300M
BNC – RG6U (75-5) 100Mbps 500M
BNC – RG59 (75-3) 10Mbps 800M
BNC – RG6U (75-5) 10Mbps 1000M

Installation view

  1. Point to Point TransmissionREPOTEC RP-EC500CK IP PoE Extender - Fig1
  2. Extra Long Extension by connecting with RP-EC500CKKREPOTEC RP-EC500CK IP PoE Extender - Transmission
  3. Long Distance for Multiple cameras transmissionREPOTEC RP-EC500CK IP PoE Extender - Transmission1

Panel Review

REPOTEC RP-EC500CK IP PoE Extender - Panel Review

No. Interface Function
1 RJ45 Connector Port 1;To connect networking devices or another IP09

(Refer to Description 1,2,3)
2| BNC Connector| Port 2;To connect the other endpoint of RP-EC500CK (Refer to Description 1,2)
3| RJ45 LED| To indicate the network connection status (Refer to Description 4)
4| Power Jack| To connect DC12V 0.5A adapter
5| Power LED Indication| To indicate the power status (Refer to Description 5)
6| Status Indication| 1. Status : Port 1 mode indication (Refer to Description 6)
2. Status : Port 2 mode indication (Refer to Description 6)
7| DIP Switch| To select the desired mode (Refer to Description 7)

Description

  1. Link speed of port 1 and 2 must be sync, or they are not able to activate network connection.

  2. Once the port 1 and 2 remain unlinked, the RP-EC500CK will automatically turn to Power Saving mode.

  3. RJ45 Pinout
    (PIN TIA/EIA-568B)

    PIN| Wire Color
    1| Orange-white
    2| Orange
    3| Green-white
    4| Blue
    5| Blue-white
    6| Green
    7| Brown-white
    8| Brown

  4. RJ45 LED
    Date Rate| Light On| Light Off| Light Blinking
    ---|---|---|---
    100Mbs| Enable| Disable| Data Transferring
    10Mbps| Enable| Disable| Data Transferring

  5. Power LED Indication
    Green On| Green Off| Light Breathing
    ---|---|---
    Power On| Power Off| Power Saving

  6. Status Indication:
    1 Status:
    **** Blue On| Blue Off| Light Blinking| Blink twice
    ---|---|---|---
    Long Reach| Ethernet| 100BaseT-T1| Hardware Failure

2 Status

Blue On Blue Off Light Blinking Blink twice
10Mbps Disable 100Mbps Hardware Failure
  1. Dip Switch Setting
    7.1 Auto Mode / Default (Highly Recommended) Dip switch 1-2-3-4 all up (OFF)
    Auto Mode to enable auto negotiation which automatically set up the link speed and transmission protocol.
    7.2 Auto+ EEE Mode Dip switch 1 down (ON), 2-3-4 up (OFF)
    Auto+EEE mode supports Energy-Efficient Ethernet based on Auto Mode.
    7.3 Advanced Mode
    Please refer to the chart below to manually set up the Link Speed, and Modes
No. Mode ↑ OFF ↓ ON
1 LINK SPEED 10Mbps 100Mbps
2 ETHERNET Disable Enable
3 100BASE-T1 Disable Enable
4 LONG REACH Disable Enable

※Link speed of 10Mbps is not supported on 100BASE-T1 mode
Auto-Negotiation Priority

Priority Mode
1 (Highest) Long Distance 100Mbps
2 100BASE-T1
3 Long Distance 10Mbps
4 100BASE-TX Full Duplex
5 100BASE-TX Half Duplex
6 10BASE-T Full Duplex
7 (Lowest) 10BASE-T Half Duplex

RP-EC500CK Package Include

2 x RP-EC500CK
2 x DC12V 500mA Power Adapter
4 x Screw
4 x Screw Plug

Specification

ITEM NO. RP-EC500CK

Support
**** Compliance| IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3bw 100BASE-T1 Ethernet IEEE 802.3 Nway Auto-Negotiation
IEEE 802.3x Full Duplex Operation And Flow Control IEEE 802.3az Energy Efficient Ethernet
Network Bandwidth| 10/ 100Mbps
Transmission Distance| 1000M at 10Mbps, 500M at 100Mbps
Ports & Interfaces
Ethernet Interface| 1 x RJ45
Link Interface| 1 x BNC
Power Interface| 2 x (2mm) DC Jack
Power
Power Supply| DC 12V 500mA Regulated
Power Consumption| 1W 90mA
Ambient Temperature
Operation| 0 to 55℃
Storage| -20 to 85℃
Humidity| Up to 95%
Physical Characteristics
Dimensions| 49 x 98.7 x 25mm
Weight| 130g

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals