REPOTEC 18-36VAC Industrial Media Converter User Manual

June 13, 2024
REPOTEC

User Manual
Industrial Media Converter, with 1 x 100M SFP + 1 x 10/100M,
18-36VAC or 12-56 VDC input

FCC MARKING

This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received; including interference that may cause  undesired operation.

CE MARKING

This equipment complies with the requirements relating to electromagnetic compatibility, EN 55032/24 class A for ITE, the essential protection requirement of Council Directive 2014/30/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.

Key Features

  • True Mini, hardened design enclosure 59x36x50mm (LxWxH)
  • Supports 18V-36VAC, 12V-56VDC or DC Jack socket
  • Supports Link Fault Pass through (LFP) function
  • Supports Switch Mode and Converter Mode.
  • Surge protection diodes on power input.
  • ESD protection diodes on RJ-45 port
  • Provides Far End Fault function on FX port.
  • Provides increased Noise Immunity
  • Extended environmental specification -40°C to 75°C

Introduction

This true mini, hardened Industrial Media Converter is designed for critical but space-limited outdoor CAM enclosure. It can be powered by wide range VAC, VDC or external DC power adapter. This unit can be either din-rail or wall mounted, both options are both included. It is an ideal unit for IP surveillance, traffic monitoring and security applications in critical environments. It can tolerate -40°C to 75°C in harsh environments to connect a reliable network.

Installation package

This unit can be din-rail mounted or wall-mounted. Din-rail brackets and wall- mount brackets are included.

REPOTEC 18-36VAC Industrial Media Converter - package

Power connection

This unit provides a 3 pin terminal block. It can be operated using either VAC or VDC power sources. The VDC power range is from 12VDC to 56VDC, and the VAC power range is from 18VAC to 36VAC. Always make sure your input voltage is within this supported voltage range.
To connect power: Follow the printed polarity for V+, V- and Ground. Connect positive wire to V+, connect negative wire to V- and also connect neutral wire to ground.
Power connecting procedure:

STEP 1 – Pull out 3 pin terminal block.
STEP 2 – Connect wire to V+, V- and Ground.
STEP 3 – Connect SC/SFP/WDM fiber wire to fiber port.
STEP 4 – Plug back 3 pin terminal block to its place.
WARNING — Always SHUT OFF power source to connect power wire.
WARNING – DO NOT force SFP fiber into SFP housing without removing terminal block.
WARNING — Any exceeded input voltage will not make this unit function and may damage this unit.
Dip switch function
This unit is equipped with dip switches, located on the front panel marked as SW1. Adjusting the dip switches will change the default function of this unit. This unit has set to manufacturer default as: Switch Mode ON and LFP function OFF.
The table shown as you may change the dip switch setting to your desired environment.

| DIP 1| UP| LFP enabled
---|---|---|---
DOWN| LFP disabled (default)
DIP 2| UP| Converter Mode
DOWN| Switch Mode (default)

LED indicator

REPOTEC 18-36VAC Industrial Media Converter - LED
indicator

Specification

IEEE Standard| IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3u 100Base-FX Fast Ethernet IEEE802.3x Flow Control and Back Pressure
---|---
Data Processing| Store and Forward
Flow Control| IEEE 802.3x Flow Control and Back Pressure
Jumbo Frame| 9KB
Architecture| Full wire speed conversion,
Transparent conversion to 802.1Q VLAN tagged packets.
Network Connector| 1 x RJ-45 10/100BaseT(X) Auto negotiation, Auto MDI/MDI-X function, Full/Half duplex
1 x 100M SFP
LED Indicators| PWR(Green): ON — Power is detected LK/Act (Green): ON — Fiber is detected Flashing— Data is transmitting/receiving
RJ-45 port
Green: ON —TX link is detected
Flashing—TX data is transmitting/receiving Amber: ON —100M speed is detected
OFF —10M speed is detected
DIP Switch| DIP1:UP—LFP enable
DOWN —LFP disable (Default) LFP (Link Fault Pass Through)
DIP2: UP—Converter Mode
DOWN—Switch Mode (Default)
Power Protection| Surge protection diodes on power input
Connector Protection| ESD protection diodes on TX port
Reserve Polarity Protection| Present
Overload Current Protection| Present
Power Input| 18V-36VAC, 12V-56VDC, DC Jack terminal cable supported (DC Barrel Connector)
Conformance to UL Standards| Use Isolated power supply to conform with UL 508 standard
---|---
Power Consumption| Full Load: 1.92Watts at 48VDC
Removable Terminal Block| 3 pin contact terminal block for power input
Wire range: 0.34mmA2 to 2.5mmA2 Solid wire (AWG):12-24/14-22 Stranded wire (AWG): 12-24/14-M Torque:51b-In/0.5Nm/0.56Nm
Wire Strip length: 7-8mm
Operating Temperature| -40°C – 75°C
Operating Humidity| 5% to 95% (Non-condensing)
Storage Temperature| -40°C – 85°C
Housing Design| IP40 Design, high graded Aluminum
Case Dimension (L X W X D)| 59 x36 x 50rtun(LxWxH)
Installation| DIN-Rail mounted, Panel Mounted

Certifications

Safety LVD (EN62368-1)
EMC/EMS CE, FCC, EN55032/24, VCCI
EMI FCC Part 15 Subpart B Class A
Vibration EN 60068-2-6
Shock EN 60068-2-27
Free Fall EN 60068-2-32

Housing Dimension (mm)

REPOTEC 18-36VAC Industrial Media Converter -
Dimension

NOTE:
Housing dimension is for the purpose of showing product Length, Width, Height, din-rail, and terminal block’s position and dimension. Please reference the LED Indicator Page for correct port order.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals