REPOTEC RP-PG2244 Unmanaged PoE Switch User Manual

REPOTEC RP-PG2244 Unmanaged PoE Switch

Overview

It is a 28-port PoE unmanaged switch series that supports up to 2410/100/1000M PoE ports, 2 10/100/1000M ports and 21000M SFP ports. 2410/100/1000M ports support PoE+, conforming to IEEE 802.3af/at standard, single port PoE power up to 30W. It provides two modes of Default and VLAN to adapt to various complex environments. At the same time, it supports the PoE usage rate indication, which is convenient to show the consumption of PoE power.

It has a high anti-interference ability, the product supports 6KV surge protection, and 6KV contact / 8KV air ESD protection.
It supports wall hanging and desktop installation, reliable and durable, and can be used in security network video monitoring, network engineering and other occasions.

Feature

• With 2410/100/1000M PoE downlink ports, 210/100/1000M uplink ports and 2*1000M SFP ports;
• The maximum PoE power of single port is 30W;
• Provides two modes of Default and VLAN to adapt to various complex environments;
• Supports PoE usage rate indication, which is convenient to show the consumption of PoE power;
• 6KV surge protection, 6KV contact / 8KV air ESD protection;
• Supports wall hanging and desktop installation

Application

Panel diagram

Front panel

Ground terminal

Attention 1: This product must be well grounded against lightning, please use better than 20# cable to connect the grounding terminal and ground.
Attention 2: Default, VLAN mode: It can be selected by dip switch.
Default: Normal switch mode.
VLAN: 1~24 ports are isolated, only can communicate with the uplink ports 25~28; restrain the network storm; close flow control.

Structure dimension

Package list

Please check the following items before installation, if any missing , please contact your local dealer.

Installation

Installation on the wall

1. Use the screws to fix the hanger, follow the figure below；
2. Drill holes on a strong position of wall and then drive the rubber plug into the hole;
3. Drive these screws into the holes.
   

Installation step

Please follow the following steps( take video monitoring for example).

1. Please turn off the signal source and the device’s power, installation with power on may damage the device:
2. Use 24 pcs UTP cables to connect 24 pcs IP cameras with the product’s1~24 RJ45 Ethernet ports;
3. Use 1 pcs UTP cables to connect switch’s uplink port with NVR and other switch:
4. Connect switch with power adapter;
5. Check if the installation is correct and device is good, make sure all the connection is reliable and power up the system;
6. Make sure every network device has power supply and work normally

Specification

Item|
---|---
Power| Power supply| AC power supply
Range of voltage| AC100~240V, 50/60HZ
Consumption| Self-consumption<20W, PoE output 270W
Ethernet ports parameter| Ethernet ports parameter| 1~24 ports: 10/100/1000Base-T 30W PoE RJ45(IEEE802.3af/at PSE)

25~26 ports: 10/100/1000Base-T RJ45 27~28 ports: 1000Base-X SFP

POE Usage rate| 20%, 40%, 60%, 80%, 90% LED indicator
Working mode| Default: common switch.

VLAN: 1~24 ports are isolated, only can communicate with the uplink

1~24 PoE ports| Support IEEE 802.3af/at, end-span, single port≦30W
Cable and distance| Use cat5e/6, 100m max.
Switch parameter| Standard| IEEE802.3, IEEE802.3u, IEEE802.3z
Switch fabric| 56Gbps
Though put| 42Mpps
Buffer| 4M
MAC address table| 8K
Indicator| Power| 1 *red
Uplink 25~28| Green LEDs indicate Link/Act
Downlink 1~24| Green LEDs indicate Link/Act, yellow LEDs indicate PoE
Protection| Surge| 6KV, standard: IEC61000-4-5
ESD| 6KV: contact / 8KV: air, standard: IEC61000-4-2
Environment| Working temperature| -10℃~50℃
Storage temperature| -40℃~85℃
Humidity| 0~95%(No condensation)
Structure| Dimension(L×W×H)| 442mm×285mm×44mm
Material| Metal
Colour| Black
Net-weight| 4KG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>