REPOTEC RP-PG2164 20 Ports Full Gigabit PoE Switch User Manual
- June 15, 2024
- REPOTEC
Table of Contents
REPOTEC RP-PG2164 20 Ports Full Gigabit PoE Switch User Manual
Overview
RP-PG2164 is 20-port POE unmanaged switch series that supports up to
1610/100/1000M POE downlink
ports, 2 10/100/1000M uplink ports and 21000M SFP ports. 1610/100/1000M
ports support PoE+, conforming to IEEE 802.3af/at standard, single port PoE
power up to 30W.
It provides two modes of Default and VLAN, to adapt to various complex environments.
It supports wall hanging and desktop installation, reliable and durable, and
can be used in security network
video monitoring, network engineering and other occasions.
Feature
- With 1610/100/1000M PoE downlink ports, 210/100/1000M uplink ports and 2*1000M SFP ports;
- The maximum PoE power of single port is 30W;
- It provides two modes of Default and VLAN to adapt to various complex environments;
- Supports POE power indication, convenient to display POE power consumption;
- Supports 6KV surge protection, 6KV contact / 8KV air ESD protection;
- Supports wall hanging and desktop installation.
Application
Panel diagram
**Front panel
**
**Back panel
**
Attention 1：This product must be well grounded against lightning, please use better than 20# cable to connect the grounding terminal and ground.
Attention 2：
Default, VLAN mode: It can be selected by dip switch.
Default: Normal switch.
VLAN: 1~16 ports are isolated, only can communicate with the uplink ports; restrain the network storm; close flow control.
Structure dimension
Package list
Please check the following items before installation, if any missing , please contact your local dealer.
Switch: 1 pc
AC cable: 1 set
Wall hanger+screw: 1 set
User manual : 1 pc
Installation
Installation on the wall
- Use the screws to fix the hanger, follow the figure below；
- Drill holes on a strong position of wall and then drive the rubber plug into the hole;
- Drive these screws into the holes.
Installation step
Please follow the following steps( take video monitoring for example).
- Please turn off the signal source and the device’s power, installation with power on may damage the device;
- Use 16 pcs UTP cables to connect 16 pcs IP cameras with the product’s 1~16 RJ45 Ethernet ports;
- Use 1 pcs UTP cables to connect switch’s uplink port with NVR and other switch;
- Connect switch with power adapter;
- Check if the installation is correct and device is good, make sure all the connection is reliable and power up the system;
- Make sure every network device has power supply and work normall
Specification
Item|
---|---
Power| Power supply| AC power supply
Range of voltage| AC100~240V,50/60HZ
Consumption| Self-consumption<10W
Ethernet portsparameter|
Ethernet ports parameter
| 1~16ports: 10/100/1000Base-T 30W PoE RJ45(IEEE802.3af/at PSE)17~18ports: 10/100/1000Base-T RJ45 19~20 ports: 1000Base-X SFP slots
Working mode
| Default mode; normal switch mode.VLAN mode: ports1~16 are isolated from each
other and can only communicate with the uplink port; restrain the network
storm; turn off the flow control.
Cable and distance| Use cat5e/6, 100m max.
Switch parameter| Standard| IEEE802.3, IEEE802.3u, IEEE802.3z
Switch fabric| 40Gbps
Thoughput| 29.8Mpps
Buffer| 4M
MAC address table| 8K
Indicator| Power| 1 *red
Uplink 17~20| Green LEDs indicate Link/Act
Downlink 1~16| Green LEDs indicate Link/Act,yellow LEDs indicate PoE
Protection| Surge| 6KV, standard: IEC61000-4-5
ESD| 6KV: contact / 8KV: air, standard:IEC61000-4-2
Enviroment| Working temperature| -10℃~50℃
Storage temperature| -40℃~85℃
Humidity| 0~95%(No condensation)
Structure| Demension(L×W×H)| 442mm×285mm×44mm
Material| Metal
Colour| Black
Net-weight| 4KG
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>