COOLON ARIA X TW High Power Tunable white AC Flood Light Installation Guide

: June 13, 2024
: COOLON

COOLON ARIA X TW High Power Tunable white AC Flood Light

COOLON ARIA X TW High Power Tunable white AC Flood
Light

INCLUDED

Box Contents

Luminaire
Mounting Brackets (Integral)

+ Run Box

Allen Key
Cable Plastic Caps
Cable Kits

CONTENTS	LxWxH DIMENSIONS
Single Luminaire	582 x 191 x 121mm
Double Luminaire	637 x 249 x 151mm
Triple Luminaire	665 x 292 x 162.5mm
Run Box	Varies depending on quantity

ATTENTION

Please observe / follow the instructions methodically.
Please ensure the units are handled with extreme care.
Do not remove product from packaging prematurely. Only remove from packaging when ready for installation.
Failure to observe installation instructions and handling will void warranty of the product.
Fittings must be installed by a licensed electrician.
Before installing, make sure the power supply is switched off or mains cable is disconnected.
Aria is designed for a wide range of applications, including those with low vibrations such as bridges and fixed metal structures. However, is not designed for heavy-duty environments with excessive vibration.

INSTALLATION LIMITS @ 230VAC

Maximum 32 x Single Luminaires per individual run.

INSTALLATION LIMITS @ 120VAC

Maximum 28 x Single Luminaires per individual run.

INSTALLATION LIMITS @ 230VAC

Maximum 16 x Double Luminaires fittings per individual run.

INSTALLATION LIMITS @ 120VAC

Maximum 14 x Double Luminaires per individual run.

INSTALLATION LIMITS @ 230VAC

Maximum 10 x Triple Luminaires per individual run.

INSTALLATION LIMITS @ 120VAC

Maximum 9 x Triple Luminaires per individual run.

WIRING CONFIGURATION

DATA Pinouts

MAINS Pinouts

WIRING DIAGRAMS

DALI INSTALLATION

0–10V INSTALLATION

CASAMBI INSTALLATION

Please refer to Casambi’s documentation about system limits and range
Please refer to CBU-A2D documentation for reference
Control limits defined by the DALI system

CONNECTION

Before installation begins, please ensure that you understand the fitting layout as per luminaire schedule.

DIMENSIONS

DIMENSIONS WITH GLARE SHIELD

MOUNTING FOOTPRINTS

MINIMUM RECOMMENDED FASTENERS PER LUMINAIRE: MOUNTING BRACKET MATERIAL: APPLICATION:
4 x M5 bolts for single luminaires Aluminium Low vibration

MINIMUM RECOMMENDED FASTENERS PER LUMINAIRE: MOUNTING BRACKET MATERIAL: APPLICATION:
4 x M12 bolts for double and triple luminaires Stainless Steel 304 Low vibration

AIMING SINGLE LUMINAIRE

STEP 1
Loosen Screws A and B counter clockwise to allow for rotation of the luminaire.
STEP 2
Rotate the luminaire to your desired angle
STEP 3
Tighten Screws A and B clockwise to lock into position (9Nm).

AIMING DOUBLE LUMINAIRE

STEP 1
Loosen the angular adjustment M8 screws.
STEP 2
Once luminaire is aimed, tighten to 7Nm. The bracket allows for 90° vertical rotation and 45° forwards rotation.

AIMING TRIPLE LUMINAIRE

STEP 1
Loosen the angular adjustment M8 screws to adjust angle of the triple luminaire array.
STEP 2
Once luminaire is aimed, tighten to 7Nm. The bracket allows for 90° vertical rotation and 30° forwards rotation.
STEP 3
This bracket also allows for individual angle adjust of each luminaire. Loosen each angular adjustment M8 screws.
STEP 4
Once luminaire is aimed, tighten to 7Nm. The bracket allows for 10° positive and negative rotation.

LUMINAIRE SAFETY LANYARD PROVISIONS

Utilize provisioned apertures if safety lanyards are required in the installation.
For maximum safety, utilize a safety lanyard for each provision including single fixtures within the double and triple arrays.
Single Luminaire

Double Luminaire
Utilize safety lanyard provisions for the bracket.

Triple Luminaire
Utilize safety lanyard provisions for the bracket.

Customer Support

archsales@coolon.com.au aus. 1300 287 533 intl. +613 8681 3633 www.coolon.com.au
All documentation is subject to change without notice. Refer to our website for the latest information.

Logo