ACROX MU137 Wireless Comfort Mouse User Guide

ACROX MU137 Wireless Comfort Mouse

Product Information

Specifications:

• Product Name: Wireless Comfort Mouse
• Wireless Technology: 2.4GHz BlueTrace
• Receiver: Nano Receiver
• DPI Settings: 800dpi, 1300dpi, 1600dpi
• Buttons: Left, Right, Scrolling Wheel, Forward, Backward

Product Usage Instructions

Installing Batteries:

1. Remove the battery cover.
2. Insert the provided AA battery into the compartment following the correct polarity.
3. Replace the battery cover.
4. Turn on the power switch.
5. Remember to turn off the power switch before travelling with the mouse.

Setting up Connection:

1. Insert the battery into the mouse.
2. Locate the storage slot on the back of the mouse to store the nano receiver and take it out.
3. Plug the Nano receiver into a USB port on your computer.
4. The LED indicator on the mouse will flash steadily in pairing mode and stop blinking when successfully paired with the receiver.
5. Monitor the battery indicator on the mouse for low battery alerts.

Frequently Asked Questions (FAQ):

• Q: How do I change the DPI settings on the mouse?
  A: Use the DPI Key to toggle between 800dpi, 1300dpi, and 1600dpi settings. The LED indicator will blink to show the current DPI setting.

• Q: What should I do if the mouse is not connecting to the receiver?
  A: Ensure that the battery is properly inserted, the receiver is securely plugged into a USB port, and follow the pairing instructions provided.

Wireless Comfort Mouse
2.4GHz Wireless BlueTrace Mouse w/ Nano Receiver

User’s Guide

CAUTION:
To use this product properly, please read the user’s guide before installing it.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement:
The product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such a function is available.

Functional Introduction

1. Left Button

2. Right Button

3. Scrolling Wheel

4. Forward
   Press this button to view the next page in your Internet browser.

5. Backward
   Press this button to view the previous page in your Internet browser.

6. DPI Key & LED Indicator

7. Nano Receiver

8. Battery Cover

9. ON/OFF Switch

DPI Switch

• A. 3 adjustable DPI settings. The blinking key indicates the DPI setting in use.
• B. Default is 1600 DPI.

Installing the Batteries

• Step 1: Take the battery cover off.

• Step 2: Insert the battery as shown inside the battery compartment.

• Step 3: Replace the cover.

• Step 4: Turn on the power switch. Warning:
  Please insert the battery in the correct position according to the instruction label on the mouse.

• Step 5: If you need to travel with your wireless mouse, make sure you turn off the power switch.

Setup the Connection Between the Receiver and the Mouse

1. Insert the battery into the mouse, then follow the steps below.

2. In the meantime, there is a storage slot on the back to store the receiver, take the nano receiver out.

3. Plug the Nano receiver into the USB port on your computer.

4. The LED indicator on the mouse flashes steadily when it is in pairing mode and stops blinking when it is successfully paired with the receiver.

5. When low battery, the battery indicator on the mouse will start to blink.

   • LED is on for 3 seconds
     Power ON

   • LED blinks 3 times
     During pairing (LED OFF when paired or failed after 10 sec.)

   • LED blinks for 10 seconds
     Low battery warning

Satisfaction Guarantee

100% Satisfaction Guarantee
If you are not completely satisfied with the quality of any Staples® Brands products, simply return them within the applicable return period along with the receipt or original package for an exchange or refund. See Staples Returns Policy for details.

• Support
  1-800-425-0049

Southern Graphic Systems, Canada (SGS&CO) dba Marks Design has made every effort to comply with Health Canada, CPLA, CPLR, CFIA, FDR, and FDA rules and guidelines in the production of this artwork. To the best of our knowledge and experience, this artwork adheres to and is compliant with rules governing product-labeling requirements as per Canadian legislation and/or USA legislation. In the event of an inadvertent non-compliance issue that results in the re-work of existing artwork, SGS&CO/Marks Design will, in cooperation with the client, make every effort to rectify the problem and produce replacement artwork files. The liability of SGS&CO/Marks Design shall be limited to correcting its product. SGS&CO/Marks Design will not assume any legal or financial responsibility or liability for the contents of any packaging in the case of said contents being unusable because of Health Canada, CPLA, CPLR, CFIA, FDR, and FDA packaging non-compliance. The supplied artwork should be approved by the recipient for all content, layout and copy accuracy. This is a mechanical artwork file only. Colour rotation is to be confirmed by the printer or prepress supplier. The UPC is FPO and should be replaced by your printer or prepress supplier. Please ensure that your prepress supplier prepares the file for printing. Refer to Pantone and process matchbooks for reflection of accurate colour, as this is not color-proof. Should the supplied artwork be found to be incorrect, please contact your representative immediately.

Copyright © 2024

TORONTO STUDIO 2 DORCHESTER AVENUE, TORONTO, ON M8Z 4W3 CANADA makemarks.com.

References

• Marks Design - Brand Strategy, Design and Communications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>