allen roth FSI 1168Q BGLD 144 Inch Brushed Gold Steel Double Curtain Rod Instruction Manual

allen roth FSI 1168Q BGLD 144 Inch Brushed Gold Steel Double Curtain Rod

Product Information

The product is a double drapery rod, designed and manufactured by ALLEN+ROTH. ALLEN+ROTH and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.

The package contents include:

• A – Quantity: 3
• B – Quantity: 2
• C – Quantity: 3
• D – Quantity: 2

The hardware contents include:

• AA – Quantity: 3
• BB – Quantity: 6
• CC – Quantity: 6

Product Usage Instructions

1. Ensure that the drapery rod is level before installation.

2. Install the drapery hooks correctly. If unsure, refer to the included instructions.

3. During installation, use a level (not included) to ensure proper alignment.

4. If the drapery rod hook is loose, check if the drapery hooks are anchored correctly. If not, follow these steps:
   a. Attach the drapery hooks to wall studs if possible.
   b. If unable to attach to studs, use the supplied anchors and screws for proper anchoring

5. After installation, ensure that all parts are securely tightened.

Care and Maintenance

Regularly inspect the drapery rod for any signs of damage or wear. Clean the rod using a soft cloth and mild detergent if necessary. Avoid using harsh chemicals or abrasive cleaners.

ALLEN+ROTH and logo design are trademarks or registered trademarks of LF, LLC.
All rights reserved.

Thank you for purchasing this allen + roth product. We’ve created these easy- to-follow instructions to ensure you spend your time enjoying the product instead of putting it together. But, if you need more information than what is provided here, please visit Lowes.com, search the item number and refer to the Guides & Documents tab on the product’s page.
If the item is no longer for sale, or if you have any questions or problems, please call our customer service department at 866-439-9800, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com.

*Image is for example only. Appearance of actual product may vary L’illustration

TROUBLESHOOTING

Drapery rod not level.

| Drapery hooks not installed correctly.

.

| Make sure to use level (not included) during installation.

Drapery rod hook is loose.

|

Drapery hooks not anchored correctly.

|

Attach drapery hooks to wall studs if possible. Use anchors and screws supplied if you can’t attach to stud.

 |  |

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 30 minutes

TOOLS REQUIRED (NOT INCLUDED

FEELING CONFIDENT? START YOUR NEXT PROJECT

CARE AND MAINTENANCE

Clean with a soft cloth.

PACKAGE CONTENTS

HARDWARE CONTENTS

INSTALLATION OVERVIEW

1. Using bracket as a guide, adjust to desired height and mark location on wall for mounting screws.

2. Remove bracket from wall. Drill pilot hole using 3/16 in. bit (not included) and insert wall anchors

NOTE
Anchors are not needed for all installation types

3. Attach bracket to wall using screws provided

4. Extend telescopic rod slightly. Remove finial from smaller

5. Slide additional rod over smaller diameter rod.

NOTE
At this point you should have a complete telescopic rod with 2 large diameter rods connected with 1 smaller diameter rod section in the middle
NOTE
Add drapery (sold separately), extend rod to desired length and hang ready rod in brackets.

6. Extend telescopic rod through center bracket and feed remaining half of curtain panels on to rod. Fully extend rod through remaining outside bracket and screw on remaining end cap.

7. Reattach finial and tighten set screws on brackets to lock rod in place.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>