GOLDEN LIGHTING 3321-BA3 PW-WHT Fraser 3 Light Pewter Bath Fixture Wall Light Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3321-BA3 PW-WHT Fraser 3 Light Pewter Bath Fixture Wall
Light
Product Information
The product is a lighting fixture manufactured by Golden Lighting. It is
available in the model number 3321-BA3 PW-WHT. The fixture is designed to
provide both task and ambient lighting in various spaces such as kitchens,
dining rooms, and open areas. It features a backplate, metal shades, sockets,
inner shade covers, socket rings, and iron cages. The fixture requires light
bulbs (not included) to function.
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island
- Center a linear pendant over the kitchen island.
- If using hanging pendants, use one pendant for every 24 inches of the island.
- Hang the fixtures at least 30 inches above the countertop.
Pendants and chandeliers Above a Dining Room Table
- Hang the fixtures at least 30 inches above the table.
- Use a fixture that is 12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas
- Ensure that the bottom of the fixture hangs at least 7.5 feet from the floor
- Allow clearance for any opening doors.
Installation
- Follow the assembly instructions provided for the specific model number 3321-BA3.
- Connect the fixture’s wires to the house wires, matching hot to hot, neutral to neutral, and ground to ground.
- Secure the fixture’s backplate to the mounting plate using small screws.
- Lift the metal shades up to the sockets and secure them in place using the inner shade cover and socket rings.
- Install light bulbs into the sockets according to the fixture’s specifications, ensuring not to exceed the maximum recommended wattage.
- Twist the iron cages into the inner shade covers in a clockwise manner to secure them.
- Turn on the power and test the fixture to ensure it is functioning correctly.
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one
pendant for every 24″ of the island. Fixtures should hang at least 30″
above the countertop.
Pendants and chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope
You love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment. Get function and style! Browse our site for coordinating lights
and expert lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral: Ribbed, White, or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT
- All installation work should be done by an accredited professional.
- Shut off the power supply at the fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove the old fixture from the wall, including the
old mounting strap.
-
The mounting plate (B) contains several pairs of threaded holes. Find the pair of holes that match the spacing of the holes on the junction box and your fixture’s backplate. Two mounting screws (C) should
be attached to the mounting plate (B). Small screws (A) may be attached to backplate (G), unscrew small screws (A) and set aside for later. -
Place mounting plate (B) over the junction box. Secure mounting strap (B) to the junction box with mounting screws (C) and a screwdriver. Tighten the screws securely. After you determine the proper placement, hold the mounting plate (B) up to the wall and use a pencil to mark the wall through the two circular holes found on the mounting plate (B).
-
Set aside the mounting plate (B) for now. Use a drill bit to create two holes on your pencil marks and insert plastic screw holders/anchors (D) into the holes made until the plastic screw holders/ anchors are flush with the wall. Align mounting plate (B) with the plastic screw holders/anchors (D). Using a drill or screwdriver, insert mounting screws (F) into the plastic screw holders/anchors (D).
-
Secure mounting plate (B) to the junction box using mounting screws (C) and a screwdriver. Tighten the screws securely. Pull the house wires through the center of the mounting plate (B).
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply
wires from the junction box. Attach the fixture’s wires to the power supply
wires from the junction box. Connect Hot to Hot (transparent wire with black
inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with
white inner thread, white, or ribbed wire), and Ground to Ground (transparent
wire with green inner thread, green wire, or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the
junction box, locate ground screw (E) on the mounting bracket/mounting strap
and wrap the fixture’s ground wire around the ground screw. Use a screwdriver
to tighten the top of the ground screw (E) onto the wires and into the
mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Place the fixture’s backplate (G) over the mounting plate (B). Align the holes
in the backplate (G) with the holes found on the mounting plate (B). Insert
small screws (A) into the holes found on the backplate (G) and mounting plate
(B). Tighten screws until backplate (G) is secure to mounting plate (B) and
the fixture is snug against the wall. Lift metal shades (I) up to sockets (H)
and secure them in place using the inner shade cover (J) and socket rings (K).
Install light bulbs (not included) into sockets (H) in accordance with the
fixture’s specifications. Do not exceed the maximum recommended wattage. Twist
iron cages
(L) into the inner shade covers (J) in a clockwise manner to secure. Your
installation is now complete. Turn on the power and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>