My Weigh R1-60 Ultraship R1 Postal Scale and Ac Adapter Pack Instruction Manual

1. My Weigh R1-60 Ultraship R1 Postal Scale and Ac Adapter Pack Instruction Manual
   

Thank you for purchasing the My Weigh® UtraShip®- R digta cal. leaseread alloperating instructions carefulybefore use. This electronic calesaprecision instrument.With normal care and proper treatment, it willpovide years ofrlableservice. For more information please visit
www.myweigh.com

protection buitino the case, verloading will permanently damage it Avoid any exposure to extreme heat or cold, your scale works better when operated at normal room temperature. Keep your scale in cean environment. Dust, dirt, moisture, vibration, ar curtents and/or aclose proximity to other electroic equipment can all cause an advers effect on the elabilty and accuracy of your scale. Handle with care. Gently applyallitems o be weighed ontotray top. Avoidshaking,dropping o otherwise shocking th scale. Scals are delicate instruments and unlike celular phones, scales have delicate sensors that determine how much an item weighs. I you drop or shack your scale,these sensors feel”the shock and are sometimes destroyed. This happens with al digital scales. We design our scals to b as esistant to shock o drops as possble, howeverthere is no way for us to protect 100% against load cellor sensor damage.
Failure to follow these instructions will void your warranty.
Always allow the scae to accimate to normal room temperature for at least one hour before use. Give your scale sufficent warm up time. Usually 30-60 seconds before calibration to give the intemal components a chance to stabilize

BATTERIES

Low Batteres & bad battery connections re the #1 cause of scale malfunction ad inaccuracy! We testalof our cal returns from consumers and 60% of them are battery elated problems. This sounds silly but i’ true! A scale will perform poorly when it has low batterie. Use good quality batteres & repace them often ( Remove the battries i you plan to stoe the scle for fonger then 14 days. Ifyourscal simply won’t tum on while on battery power,itisoften caused by loose battery connections. Battery prongs (terminals)are made of metal and they have to bein contact withthe batteres.You can use papercip to lghtly bend the battery prongs to have better connection. Some poorly designed batteries have recessed or partally obstructed battery terminals. This may cause your prongs to b touching the plastic housing of the battery
instead of the metal of the battery terminal,

Battery installation

a) Press and lft open the battery cover located at the bottom of the it
b) Insert the batteries and make sure the polarity i corect (+) and (- . ) Close the battery cover unil it lick shut Note: s time to eplace the bttery ifth dispaly shows “Lo”when powered on and then it will tu offautomatically.

OPERATION INSTRUCTIONS

Weighing Procedures

1. 1.ress [ @] o tum on the scale. When the power is tumed on, the scale will countdown for a few seconds and “0” will appear on the display.
2. electthe weighing unitwith [UNIT key. Press [UNIT] toselectaweighing unit g, kg, oz, I, Iz Oncethe nithas been selcted, the slected nit wil b displayed next o the weght value.
3.  Start weighing Verfythe reading s “0”. Place abjectson the weighing platform to weigh. When th reading becomes stable the stable indicatoris displayed,
   TARE Tare can be used fo eliminating the weight value of an empty container. Place an empty container onthe scale an press [TARE/ZERO]. Then placethe ems to be weighed inthe contaner, NOTE: When allweight is removed from the weighing tray the tared value o a container will e displayed as a negative number.Press [TARE/ZERO] again to etur thescae to zer,

CALIBRATION

Galbration may be required when the scle i firtset up or use, o i the scale s moved toa diffeent ltitude ornew location. Thisis necessary because the welght of a mass n one location s ot necessarily the same n another location. Also, with time and use, mechanical deviations can occur.

1. Turn the scale OFF and place it on a fla,verystable surface.
2. Press and hold both [UNIT} and [ @ ]t turn on the scaleand then release the keys, waitfor the isplaytoshowCLxx”(ox number s the vequired calibation weigh), you ca pressthe [UNIT] key to change the calibration unitbetween“Lb” and”kg”
3. Press the [HOLD] key to change the value of ten i, and pressthe [TARE/ZERO] ey to change the value o uitsdigt, and then pressthe [@]keyto onfirm the calbration weight. Th dispay wil lash“CLx” I the required weight i too small o ver the range, it will displayErr”
4. Place the calbration weigh(s) eeded onthe center of the try, then press [TARE/ZERO), The display wllshow“CAL anthen the display ‘willshowPASS” Calibration i complete. After a few seconds, the scale will eturnto normal weighing mode. Remove the weight from the tray and tun the scale Off.

FEATURES

Overload Indicator When the display shows” 0_LD’ tisindicates an overload. Remove excesiveload immediately. Remerber: you an pemanently damage thescale and void your warranty by overloading it!
Negative Value Anytare value will e displayed as a negatve number once all weight s removed,press [TARE /ZERO) o e-zerothe scale.
Auto Off/ Backlight Setting An auto shut offfeature i provided to conserve battery power. The scale will automatially tumoff after 2 minutes ofinactivity. To adjust the auto off & backlight settings follow these instructions:

1. Press and hold [HOLD] and power on the scale with [ @ ], then release both keys.

2. .The display will now show “oFF 0″ (auto-off disabled), “oFF 1″ (automatic turn off after about 2 minutes – Default setting), or ofF 2″
   (automatic tur off after about 5 minutes. Press [HOLD] to toggle and [TARE/ZERO] to confirm and enter backlight settings.

3. The display will now show “BL 0″ (backight disable), L 1″ (backlight always on – Default stting), or“BL 2 (backlight automatically
   ‘turns on when scale is in use). Press [HOLD] to toggle the settings.

4.  Press [TARE/ZERO] to confirm your selection. The scale will now return to normal weighing mode.

Hold

Press the [HOLD) to hold urrent weight eading, press [HOLD) again o cncel,

REMOVABLE DISPLAY OPERATION

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>