My Weigh 8-300 Palm Scale User Manual
- June 12, 2024
- My Weigh
Table of Contents
My Weigh 8-300 Palm Scale
Thank you
Thank you for purchasing the My Weigh” Palmscale-8° digital scale. Please read
all operating instructions carefully before use. This electronic scale is a
precision instrument. With normal care and proper treatment, it will provide
years of reliable service. For more information please visit
www.myweigh.com.
Never load the scale with more than the maximum capacity. Although the
Palmscale-8″ is designed to be extremely durable with extra overload
protection built into the case, overloading will permanently damage it! Avoid
any exposure to extreme heat or cold, your scale works better when operated at
normal room temperature. Keep your scale in a clean environment. Dust, dirt,
moisture, vibration, air currents and/or a close proximity to other electronic
equipment can all cause an adverse effect on the reliability and accuracy of
your scale. Handle with care. Gently apply all items to be weighed onto tray
top. Avoid shaking, dropping or otherwise shocking the scale. Scales are
delicate instruments and unlike cellular phones, scales have delicate sensors
that determine how much an item weighs. If you drop or shock your scale, these
sensors”feel”the shock and are sometimes destroyed. This happens with all
digital scales. We design our scales to be as resistant to shock or drops as
possible, however there is no way for us to protect 100% against load cell or
sensor damage. Failure to follow these instructions will void your warranty.
| Model | Capacity | Precision |
|---|---|---|
| 8-300 | 300g | 0.01g |
| 8-800 | 800g | 0.1g |
Always allow the scale to acclimate to normal room temperature for at least one hour before use. Give your scale sufficient warm up time. Usually 30-60 seconds before calibration to give the internal components a chance to stabilize.
BATTERY INSTALLATION
a) Press and lift open the battery cover located at the bottom of the
unit.
b) Insert 2xAAA batteries and make sure the polarity is correct(+) and (-
).
c) Close the battery cover until it clicks shut.
Note: If the battery symbol appears in the display, it means low battery power. It is time to replace the battery.
OPERATION INSTRUCTIONS
WEIGHING PROCEDURES
- Place the scale on a flat hard surface.
- Press to turn on the scale. Please allow 5 seconds for the scale to perform power up systems check.
- Press [MODE] to select a weighing unit.
- Gently place the items to be weighed on the scale platform.
UNIT PRICING
- Press to increase or to decrease the unit price by 10.
- Press to increase or to decrease the unit price by 1.
- Press IM I to save the unit price. It will automatically restore this saved unit price on restarting the scale every time.
every time.
TARE
Tare can be used for eliminating the weight value of an empty container. Place an empty container on the scale and press . Then place the items to be weighed in the container. NOTE:When all weight is removed from the weighing tray, the tared value of a container will be displayed as a negative number. Press again to return the scale to zero
AUTO POWER OFF
- In normal weighing mode, press the , display will show”Ofl1″ = (auto off 30 seconds) or “OFF 2” (auto off 1 minute) or “OFF 3” (auto off 2 minutes).
- Choose the auto turn off time by pressing [MODE], confinn your selection by pressing . The scale will return to normal weighing mode.
CALIBRATION
Calibration may be required when the scale is first set up for use, or if the scale is moved to a different altitude or new location. This is necessary because the weight of a mass in one location is not necessarily the same in another location. Also, with time and use, mechanical deviations can occur.
For Palmscale 8-300 you will need a 200g weight and for Palmscale 8-800 use a 500g weight.
- Tum on the scale and wait for the scale to stabalize.
- Place the correct calibration weight on tray.
- Press and hold [MODE) until the calibration weight flashes on the display.
- Calibration is complete when “PASS” is displayed.
If the displays shows “FA Ir; please recalibrated the scale again.
FEATURES
POWER UP SYSTEM CHECK
When first turning the unit on, the scale will run a quick diagnostic and it
will display a countdown. This display will remain for a few seconds and then
reset to zero.
OVERLOAD INDICATOR
When the display shows”——-/OVERLOAD’; this indicates an overload. Remove
excessive load immediately. Remember: you can permanently damage the scale and
void your warranty by overloading it! NOTE: The display will also show “——-”
if a negative weight is lower than the negative range of the scale.
TRIPLE HIGH DEFINITION DISPLAY
Unparalleled clarity and ease of use.
INDUSTRY LEADING DESIGN AND TECHNOLOGY
Looks good and designed to last.
SAMPLING TOOL & TWEEZERS INCLUDED IN THE SCALE BODY
Great for weighing on the go.
PROPRIETITRYWEIGHMETER TECHNOLOGY
Prevents accidental overloading.
SPECIFICATIONS
Capacity| 300gx0.0lg 800gx0.lg| Units| g,114oz,1/8oz,oz,gn,ct, dwt
g,1/4oz,1/8oz,oz, ozt,ct, dwt
---|---|---|---
Scale dimension| 120m x 78mm x 20mm
Tray dimension| 65mmx68mm
Scale Weight| 180g
Operating temperature| Optimum l0·40’C (50·104’1)
Power Source| 2xAAA
Tare range| Up to scale’s maximum capacity
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>