DJI 6941565922595 Wireless Microphone System User Guide

DJI 6941565922595 Wireless Microphone System

Introduction

DJITM Mic is a dual channel wireless microphone system, including two transmitters and one receiver, which is able to record two sound sources simultaneously at a distance of up to 250 m*. The transmitter has a built-in omnidirectional microphone, supports the use of an external microphone, and can be clipped to clothing or any place close to a sound source. With the internal 8 GB storage, DJI Mic is able to record audio for up to 14 hours**.

The receiver boasts an OLED touchscreen, on which users can view the real-time volume, wireless signal strength, gain, recording modes, and more. By utilizing the expansion port, the receiver can be connected to a camera or mobile phone to provide high quality audio. The receiver can also be connected to a computer to use as a microphone and with the monitor port the audio can be monitored in real time. The charging case provided is able to charge the transmitters and receiver simultaneously and link them automatically.

Tested in an obstruction-free outdoor environment.  Tested with a 48,000Hz sampling rate and 24-bit mono WAV audio format.

DJI Mic Transmitter

System Status Indicator

Indicates the connection status with the receiver and the battery level of the transmitter.

• Data Port (USB-C) For copying audio or updating firmware after connecting to a computer. Can also be used for charging.
• Power Button Press and hold to power on or off. Press twice to mute.
• Internal Microphone For recording audio.
• 3.5 mm TRS Input For connecting external microphone. DO NOT connect a microphone with a power supply of 24 V or 48 V.
• Recording Status LED Indicates the record status of the transmitter
• Linking Button Press and hold to start linking to the receiver. Once the receiver is attached to a mobile phone and the receiver and transmitter are linked, press once to take a photo or start or stop recording on the mobile phone (only supports mobile phones where the volume button can be used to take a photo or start or stop a video).
• Record Button Press once to start or stop recording.
• Charging Pad Charging will begin after connecting the transmitter to the charging pad of the charging case and the transmitter will automatically link with the receiver in the charging case.

DJI Mic Receiver

OLED Touchscreen

Displays information such as the real-time volume, battery level of the receiver and transmitter, charging status, wireless signal strength, gain, and recording modes. Slide down or up on the screen to access settings.

1. Power Button Press and hold to power on or off. Press once to lock or unlock the screen.
2. Data Port (USB-C) After connecting to a computer, can be used to update firmware or as a microphone for the computer. Can also be used for charging.
3. Monitor Port Plug in a 3.5 mm TRS headphone to monitor the transmitter recording.
4. 3.5 mm TRS Output For audio output to a camera. DO NOT connect to a device with an output of 24 V or 48 V.
5. Expansion Port For connecting to a mobile phone using a mobile phone adapter or connecting to a camera using a hot shoe adapter.
6. Charging Pad Charging will begin after connecting the receiver to the charging pad on the charging case and the receiver will link with the transmitter in the charging case automatically.

Charging Case

1. USB-C Charging Port For charging the charging case.
2. Battery Level LEDs Indicates the battery level of the charging case.

Operation

Linking The transmitters and the receiver are linked by default. Follow the steps below to link if the transmitter and receiver are disconnected.

1. Place the transmitters and the receiver in the charging case and they will link automatically.
2. Power on the transmitter and the receiver, press and hold the link button of the transmitter, slide down on the screen of the receiver, select Settings, and scroll through and tap Link Device to start linking. The status LED glow solid green to indicate linking is successfull.

Using DJI Mic

Transmitter The transmitter can be attached using the magnetic clip to either clothes or a stable surface. The clamp can also be used to attach the transmitter to clothes.

It is recommended to use the windscreen when using the transmitter outdoors or in a windy environment. Attach the windscreen to the transmitter by aligning it with the internal microphone and rotate the windscreen to lock in place.

Receiver

Using with a Camera To record audio and transmit to a camera, attach the receiver to a camera using the hot shoe adapter and connect to the microphone port of the camera using the camera cable provided.

Lower the volume of the camera to avoid sound distortion.

Using with a Mobile Phone Attach the receiver to a mobile phone using the mobile phone adapter to record audio and transmit to a mobile phone. Audio can be played after the receiver is disconnected from the mobile phone.

• The 3.5 mm TRS output port of the receiver cannot output after connecting to a mobile phone adapter.
• Only Mono mode can be used after connecting the receiver to the Lightning mobile phone adapter.
• The mobile phone speaker cannot output sound after connecting the receiver to the mobile phone. Bluetooth headphones or speaker can be used instead.

Using with a Computer Connect the receiver to a computer via the USB-C port as a microphone for a computer.

Use a standard charging cable to connect DJI Mic with a computer and enter the related input settings on the computer.

**OLED Touchscreen Operations

**

Home

The top part of the screen indicates the status of receiver.

•  Recording Mode. Choose between S (Stereo), M (Mono), and Ms (Mono Safety Track).
• Indicates the receiver gain.
• Indicates there is external headphone connected.
•   Indicates the wireless signal strength between transmitter 1 and the receiver. If there is only ne transmitter connected, then only the information of one transmitter will be displayed.
• Indicates the wireless signal strength between transmitter 2 and the receiver.
• Indicates the battery level of the receiver. The middle of the screen indicates the status of transmitters.
• Indicates the transmitter gain.
• Indicates audio is being recorded
• Indicates the sound channel.
• Indicates the battery level of the transmitter The bottom of the screen indicates the real-time volume.
• Indicates the volume of the internal microphone.
• Indicates volume is muted.
• Indicated the volume of the external microphone.

Settings

• Slide Down Slide down from the top of the screen to access Settings, slide left or right to select an option, and slide up to return to the previous screen.
• Recording Mode Settings Choose between S (Stereo), M (Mono), and Ms (Mono Safety track).
• Mono Under Mono mode, the audio recorded by the two transmitters will be in one channel .
• Mono with Safety Track Similar to Mono mode, the audio will be recorded in -6dB in case the main track gets distorted due to a sudden increase in the audio volume of the source.
• Stereo: Under Stereo mode, the audio will be separated into left and right channels.
• RX Gain: Can be reduced if the sound is distorted.
• Monitor Volume: Tap to adjust the volume of the receiver.

General Settings

• Low Cut  Sounds that are 150 Hz or lower will be filtered if Low Cut is enabled.
• Vibration Notification: Enable or disable vibration notification. Once Vibration Notification is enabled, the transmitter will vibrate in the scenarios listed below.
• Link Device: Tap to link the transmitter and receiver.
• Transmitter Gain: Tap to adjust the transmitter input gain according to the real-time volume. Reduce the gain accordingly when the volume bar turns red. Note that the transmitter gain will affect the volume of the recorded audio.
• Brightness: Tap to adjust the brightness of the screen.
• Language: The screen supports languages of English, Chinese Simplified, Chinese Tranditional, Japanese, Korean, Thai, German, Spanish, French, Portuguese, Italian,  Russian, Turkish, Indonesian, and Polish.
• Date and Time: Set the date and time for the recording file.
• Restore: Tap to reset default settings.
• Version: Check the SN, receiver firmware version, and the connected transmitter firmware version.
• Compliance Information: View the compliance information.

Slide Up
Slide up from the bottom of the screen to view and control recording, enable or disable mute, and view the remaining recording time. Slide up from the bottom of the left side of the screen to adjust the settings for transmitter 1 and slide up from the bottom of the right side of the screen to adjust the settings of transmitter 2.

Transmitter Recording

After powering on the transmitter, press the record button once to start recording and press again to stop recording.  The recorded audio format of the transmitter is 24-bit mono WAV. When recording for an extended period, the file will be separated automatically every 30 minutes. Th max recording time is approximately 14 hours, at which point newly recorded audio will overwrite the older recorded audio if the storage is full.

Audio File
The recorded audio can be exported or deleted after connecting to a computer and can be formatted via the receiver.

Updating Firmware

When there is new firmware available, update the firmware by connecting the transmitter and the receiver to the computer separately.

How to update firmware

1. Download the firmware on the product page at www.dji.com/mic/downloads.
2. Connect the transmitter or receiver to the computer using the USB-C cable provided.
3. Place the downloaded firmware update package .bin file under the root directories of the transmitters and receiver.
4. The transmitters and receiver firmware updates will start automatically after disconnecting from the computer.

If the firmware update fails, download the firmware again, reboot the receiver or transmitter, and repeat the steps above. After the firmware update is completed, check the firmware version on the receiver to ensure the firmware is updated successfully.

Charging Case Operations

It is recommended to charge the charging case using a 5V/2A charger. The charging case has a built-in battery with a 2600 mAh. Place the transmitter and receiver into the charging case to begin charging. With the charging case opened, the receiver displays the battery level of the three devices and the remaining recording time of the transmitter. The transmitter and receiver will be powered on once removed from the charging case. The total operating time is approximately 15 hours when using the transmitters, receiver, and the charging case together. A mobile phone adapter and the hot shoe adapter can be placed into charging case either mounted to the receiver or not.

Specifications

After-Sales Information

Visithttps://www.dji.com/support to learn more about after-sales service policies, repair services, and support. This content is subject to change. Download the latest version from https://www.dji.com/mic  If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. Copyright © 2021 DJI All Rights Reserved.

Frequently Asked Questions

What port does the transmitter have? does my microphone need a trs or trrs?

There is a 3.5 mm TRS input for connecting an external microphone. Do not connect a microphone with a power supply of 24V or 28V.

How do i connect it to my samsung s9 phone, I tried the c adapter and using the cord jack but nothing?

I have a Samsung galaxy A53 and I use the type C on the receiver and plug it into my phone and when you get done using it the file should be saved on the Microphone and you have to use the type C to Type C cable that comes with the DJI setup and plug it into your phone and then the microphone that you use and you should be able to see the audio files.

Does this microphone work on dji mavic 2 smart controller?

Please note that cameras, mobile phones (Lighting &Type-C port only), tablets, PCs, DJI Action 2 are supported.

Can the DJI mic system work with the pocket 2?

DJI MIC can work with DJI Pocket2. You need to use the 3.5mm camera cable to connect DJI Pocket 2 Do-It-All Handle with DJI Mic receiver.

Will you need to get a trs to trrs cable if you are connecting to a usb c to 3.5mm adapter?

Yes. You can use DJI Mic 3.5mm TRS Cable to connect DJI Mic receiver to 3.5mm TRS port on the adapter.

I would like to use this system for an interview similar to a podcast but in front of an audience using a mixer and powered speakers. Will this work?

Yes although you would need an adapter from the 3.5 jack to an XLR I believe. I use it via an XLR non phantom power adapter.

How long can you record on one charge?

Up to 5.5 hours of audio recording is supported when the battery is fully charged. Besides, DJI Mic transmitter is capable of recording up to 14 hours of 24-bit uncompressed audio when connected with a power source.

Does the transmitter have to be attached to the camera or can it be wire connected and mounted somewhere else?

Cameras, mobile phones (Lighting &Type-C port only), tablets, PCs, DJI Action 2 are supported by DJI Mic.

Does this record line level inputs? Mixers, audio interface etc?|

Mostly.

Does it record two channels or is one split into two stero tracks like Rode wireless Go?

DJI Mic supports three different sound channel modes: Mono, Mono Safety Track, and Stereo. Differences are as follows M (Mono): Under Mono mode, the audio recorded by the two transmitters will be in one channel.

Is there a quality wireless handheld microphone that will plug into the receiver of this?

I’d use one DJI Mic and have other handheld.
If yes, we are sorry that our RX of DJI Mic cannot directly connect to a microphone.

Is it possible to use this in a streaming as an active mic that’s connected connected to a camera that will be used in the stream like asmr?

Yes. Please note that it supports this situation.

Is it possible to use wireless earbuds with this? Or does it cause interference? I’d like to use this both for videos and virtual interviews.

At present, the DJI Mic transmitter only supports TRRS 3.5mm plug devices and does not support other wireless connection methods such as Bluetooth.

Does this come with a cable to plug into iPhone lighting connector (sc15)?

Yes, it does!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>