Fujikura SS110 Specialty Fiber Stripper User Manual

Fujikura SS110 Specialty Fiber Stripper

Product Information

Specifications:

• Product Name: Specialty Fiber Stripper SS110
• Manufacturer: Fujikura

Description of Product:

The Specialty Fiber Stripper SS110 is a high-quality fiber stripping tool designed for precision and efficiency. It is specifically designed for use with specialty fibers. This product is essential for professionals working in the fiber optics industry.

Description of Stripper:

The stripper is equipped with advanced features to ensure accurate and clean stripping of specialty fibers. It is designed to handle various types of specialty fibers with ease, providing consistent results every time.

Functions and Names of Operation Keys:

The Specialty Fiber Stripper SS110 is equipped with intuitive operation keys that allow easy control of the stripping process. The functions of each key are clearly labeled for user convenience.

Mode Settings:

The stripper offers multiple mode settings to accommodate different fiber types and stripping requirements. Users can select the appropriate mode based on the specific fiber being stripped.

LED Display:

The LED display provides real-time feedback on the stripping process, allowing users to monitor the progress and ensure optimal stripping results.

Product Usage Instructions

Setting Up the Stripper

How to Replace the Blade:

1. Ensure the power is turned off and the stripper is disconnected from the power supply.
2. Remove any fiber holder from the stripper.
3. Unlock the blade holder by turning it counterclockwise.
4. Remove the old blade from the holder and dispose of it properly.
5. Insert a new blade into the holder, making sure it is securely in place.
6. Lock the blade holder by turning it clockwise until it is firmly tightened.
7. Reattach the fiber holder if necessary.

Heater Height Adjustment:

Proper heater height adjustment is crucial for achieving optimal stripping results. Follow these steps to adjust the heater height:

1. Ensure the power is turned off and the stripper is disconnected from the power supply.
2. Loosen the heater height adjustment screws.
3. Adjust the heater height according to the fiber type andstripping requirements.
4. Tighten the heater height adjustment screws to secure the desired position.

Applicable Fiber Holder:

The Specialty Fiber Stripper SS110 is compatible with various fiber holders. Use the appropriate fiber holder based on the specific fiber being stripped. Refer to the product documentation for more information on compatible fiber holders.

Stripping Operation

Power Supply:

Ensure that the stripper is connected to a reliable power supply before starting the stripping operation. Follow all safety precautions while handling electrical equipment.

Turning Power ON/OFF:

To turn on the power, press the power button located on the control panel. To turn off the power, press and hold the power button until the device shuts down.

Stripping:

1. Select the appropriate mode based on the fiber type and stripping requirements.
2. Place the fiber into the fiber holder, ensuring it is securely held.
3. Activate the stripping process by pressing the start button.
4. Monitor the LED display for real-time feedback on the stripping process.
5. Once the stripping process is complete, remove the stripped fiber from the fiber holder.

Daily Maintenance

Perform regular maintenance to ensure the optimal performance and longevity of the Specialty Fiber Stripper SS110. Follow these guidelines for daily maintenance:

1. Turn off the power and disconnect the stripper from the power supply.
2. Clean the stripper using a soft cloth and mild cleaning solution.
3. Inspect the blade for any signs of wear or damage. Replace if necessary.
4. Check all connections and screws for tightness. Tighten if needed.

Warranty and Contact Address

Warranty:

The Specialty Fiber Stripper SS110 is covered by a warranty. Refer to the warranty documentation for detailed terms and conditions.

Contact Address:

If you have any questions or need further assistance, please contact our customer support team at the following address:

Address: [Insert Address]

FAQs

Q: Can I use the Specialty Fiber Stripper SS110 with standard optical fibers?

A: No, the Specialty Fiber Stripper SS110 is specifically designed for use with specialty fibers. Using it with standard optical fibers may result in inaccurate stripping or damage to the fibers.

Q: How often should I replace the blade?

A: The frequency of blade replacement depends on the usage and condition of the blade. It is recommended to inspect the blade regularly and replace it when signs of wear or damage are visible.

Q: Can I adjust the heater temperature?

A: No, the heater temperature is pre-set and cannot be adjusted manually. The stripper is designed to provide optimal stripping results without the need for temperature adjustment.

Thank you for purchasing Fujikura’s Specialty Fiber Stripper.
Please read this instruction manual carefully before operating the equipment.
Adhere to all safety instructions and warnings contained in this manual.
Keep this manual in a safe place.
There may be updates without notice.

Please consent beforehand.

The software equipped in the specialty fiber stripper and its related documents are protected by copyright laws and international treaty provisions as well as other intellectual property laws.
Copying some or all of instruction manual without notice is prohibited. Moreover, without permission from our company, it may not be used under the Copyright Act except when used as an individual.

Safety Information

Thank you for purchasing Fujikura’s Specialty Fiber Stripper.
In this instruction manual, the processes and procedures are documented which should be observed in order to use this product safely.

Follow all safety instructions
Read and understand all safety instructions.

Stop using it when it malfunctions
Ask our service centers for repair as soon as possible.

Instruction Manual
Read this instruction manual carefully before operating the machine.
Store this instruction manual in a safe place.

The following symbols are used in this instruction manual to indicate warning and caution for safe use. Learn and understand the meanings of these symbols.

WARNING! / CAUTION!
There is a possibility of death, serious injury, or physical loss if this indication is ignored. Ignoring this indication is an improper use of the machine.

PAY ATTENTION!
In general, a yellow triangle means the associated caution should be observed.

Example:
PAY ATTENTION to hot surface!

DO NOT …!

Example:
DO NOT disassemble!

DO
A blue circle with a white graphic inside means the associated process is required for safe operation

Example:
You must disconnect the plug!?

WARNING / CAUTION

Disconnect the AC power cord from the AC adapter inlet or the wall socket (outlet) immediately if user observes the following or if the stripper receives the following faults:

• Fumes, bad smell, noise, or over-heat occurs.

• Liquid or foreign matter falls into cabinet.

• Stripper is damaged or dropped.

• If this occurs, ask our service center for repair. Leaving the stripper in a damaged state may cause equipment failure, electric shock or fire and may result in personal injury, death or fire.

• The AC adapter supplied with this product is the only adapter approved for use with this product.
  Using an improper AC power source may cause equipment damage, fumes, electric shock, or fire and may result in personal injury or death.

• Connect AC power cord properly to the AC Adapter and to the wall outlet. When inserting the AC plug, make sure there is no dust or dirt on the terminals. Insert the female plug into the AC Adapter and the male plug into the wall outlet until both plugs are fully seated. Incomplete engagement may cause fuming, electric shock, equipment damage, or fire and may result in personal injury or death. Disconnect the AC power cord when the stripper is not being used.

• Do not disassemble or modify this product or the AC adapter in any way. In particular, do not remove or bypass any electrical or mechanical device (e.g. a fuse or safety switch) incorporated into the design and manufacturing of this equipment. Modification could cause damage that may result in electric shock, fire, personal injury, or death,.

• Use the supplied AC power cord. Do not place heavy objects on the AC power cord. Use of an improper or damaged cord may cause equipment failure, electric shock, or fire and may result in personal injury or death.

• Safety glasses should always be worn during the fiber preparation. Fiber fragments can be extremely dangerous if it comes into contact with the eye, skin, or is ingested.

• The blade is extremely sharp. Do not touch the edge of blade as personal injury may result during the blade replacement.

• Do not touch the stripper, AC power cord and AC plugs with wet hands. This may result in electric shock.
  If this product is wet, do not turn it on and wipe off any moisture thoroughly with a dry cloth before use.

• Do not operate the stripper near hot objects, in hot environments, in dusty/humid environments, or when water condensation is present on the unit. This may result in electric shock, malfunction, or poor stripping performance. When water condensation is present, leave the stripper powered off and allow to air-dry at room temperature for at least 24 hours.

• Do not store the stripper in any place where temperature and/or humidity are extremely high. Such environments may cause damage to the stripper.
  Before turning on, make sure to confirm that there is no abnormality in this product after long-term storage.

• Do not place the stripper in an unstable or unbalanced position. The stripper may shift or lose balance, causing it to fall. This may result in personal injury or equipment damage.

• The stripper is precision-adjusted and aligned. Do not allow the unit to receive a strong shock or impact. Possible equipment failure may result. Use the supplied box for transportation and storage. The box will protect the stripper from damage, moisture, vibration, and shock during transportation.

• Always set the blade to the correct position in the machine. Setting the blade to an incorrect position may cause serious damage to the machine.
  If the blade is replaced, only use the manufacturer-specified part. Failure to do so will result in serious damage to the machine.

• Do not touch heater during operating. The heater surface is very hot and touching this may result in skin burn.
  When removing the coating from the heater, do not touch the blade with fingers. Please use the supplied brush to clean.

• The stripper requires no lubrication. Oil or grease may degrade the stripping performance and damage the stripper.

• Be sure to read the instruction manual and understand how to use it before starting to use it.

• The equipment must be repaired or adjusted by a qualified technician or engineer. Incorrect repair may cause fire or electric shock. Should any problems arise, please contact the authorized distributor.

• Do not allow dust or dirt to enter this product. This may result in poor stripping or cause a malfunction.

• Do not use the stripper for anything other than stripping optical fibers. Using it for any other purpose may damage the stripper.

• Do not use any chemical other than pure alcohol (99% or greater) to clean the heater and others. Otherwise blurring, discoloration, damage or deterioration may result.

RECYCLING and DISPOSAL

In European Union
In accordance with the European Parliament Directive, electrical parts and materials that can be re-used and/or recycled have been identified in order that the use of new resources and the amount of waste going for landfill can be minimised.
In the European Union, do not discard this product as unsorted municipal waste. Contact your local authorities for further information.

In other countries

[Recycling]
To recycle this product, disassemble it first, sort each part separately by material components and follow your local recycling regulations.
[Disposal]
This product can be disposed of same as the standard electric poroducts. Follow your local disposal regulations.

General Information

Introduction

This product is designed to remove the outer coatings from optical fibers by using a thermally assisted mechanical stripping process. The fiber is first heated to expand the outer coating and decrease its adhesion to the fiber’s cladding. The fiber’s coating is then mechanically removed by using a pair of stripping blades.??

SS110

Applicable fibers:

• Fiber count : Single
• Cladding diameter : 125μm
• Coating diameter : 250μm

Different diameter optical fibers are applicable with optional blades.

Components

The items in the standard package are as follows. Please confirm that all items are included.

Standard Package List

The fiber stripping conditions can be edited by connecting the SS110 to a PC via a USB cable and using the “Data Connection” application.

Additional Options List

__

__

__

__

Stripper Blade

| SB-SS110-80- 160| Blade for 80μm Cladding Diameter 160μm Coating Diameter
SB-SS110-125- 250| Blade for 125μm Cladding Diameter 250μm Coating Diameter
SB-SS110-125- 900| Blade for 125μm Cladding Diameter 900μm Coating Diameter
SB-SS110-250- 400| Blade for 250μm Cladding Diameter 400μm Coating Diameter
SB-SS110-400- 550| Blade for 400μm Cladding Diameter 550μm Coating Diameter
Fiber Holder Adapter| AD-SS110-FH70| Fiber Holder Adapter for FH-70

Description of Product

Description of Stripper

Functions and Names of Operation Keys

The current stripper state can be checked using the operation keys and LED Indicators.

base to its home position after stripping is complete._
__

__

F1 key

| Shifts to heat temperature setting mode. Press this key to confirm the current heater settings. Press and hold the F1 key to change the heating temperature.

The F1 key is also used to change parameters when changing various conditions.

__

__

F2 key

| Shifts to fiber strip setting mode. Press key to confirm the current fiber strip settings. Press and hold the F2 key to enable to change the fiber strip conditions.

The F2 key is also used to change parameters when changing

various conditions.

F3 key| The| F3| key is used to change parameters when changing various
conditions.

Maintenance Mode

To enter Maintenance Mode, turn the power off while holding the F1 key. The fiber holder base will retract, then the stripper will turn off.

Mode Settings

This product is equipped with three LEDs to confirm heating temperature setting, fiber strip setting, and operation status.

LED Indicators to confirm the heating temperature

Press F1 key to enter the heat temperature setting mode for the fiber strip settings.

When a fiber stripping mode is selected, the LED indicators will light up and/or blink RED for a few seconds to indicate the temperature for the selected mode. Refer to the table below to determine the temperature being used.
A combination of the three LEDs illuminate to indicate the heating temperature according to the strip settings.

For Example:

How to read the LED Indicator combinations

The LEDs displayed for each temperature setting are as shown below.

How to change the heating temperature setting

Press and hold F1 key to enter heat temperature setting mode. While the LED is lit at the set temperature, the heating temperature can be decreased by pressing the F1 key and increased by pressing the F3 key.
The LEDs will light up in response to changes in temperature.

Heating temperature setting mode

to decrease| Pressing the F1 key in the heat temperature setting mode will lower the heating temperature in 10 C increments.

Use this function when you want to lower the temperature from its current state.

Confirm the heating temperature by reading the LED indicators after the change.

to increase| Pressing the| F3| key in the heat temperature setting mode
will raise the heating temperature in 10 C increments.

Use this function when you want to raise the temperature from its current state.

Confirm the heating temperature by reading the LED indicators after the change.

The values can also be changed by connecting the stripper to a PC and using the provided software.

LED Indicators to confirm the stripping mode

Press the F2 key to enter the mode for confirming the strip setting, and when the F2 key is  pressed, each LED will light up for a few seconds.
As shipped from the factory, one of the three LEDs will illuminate GREEN to indicate the selected stripping mode as shown in the table below.

How to change the stripping mode

Press and hold the F2 key to enter the mode for switching the strip settings. When the F1,F2, or F3 key is pressed, the corresponding LED will blink to confirm that the stripping  settings have been changed.

Setting mode| Stripping Mode Settings (Parameters can be edited by the software)
---|---
Mode 1

__

| __

__

Heating temperature 140 C __Heating time 3 seconds

Mode 2

__

| __

__

Heating temperature 180 C __Heating time 5 seconds

Mode 3

__

| __

__

Heating temperature 200 C __Heating time 10 seconds

The setting values can be changed by connecting the stripper to a PC and using the provided software.

LED Indicators

You can check the status of the stripper by the lighting or flashing of the LED.

Using the FH110 fiber holder
When using the FH110 fiber holder, the user can register the coating removal conditions to each fiber holder. Using this function, the stripping mode can be automatically changed and stripping executed according to the registered conditions.
By connecting the stripper and a PC with the provided software, the stripping conditions can be registered to a fiber holder.

| LED indicators when a FH110 fiber holder is registered
---|---

__

| LED 3 is lit GREEN

If the FH110 fiber holder attached to the stripper has a registered stripping mode, and the stripping conditions have been automatically set.

*If the main switch blinks when the fiber holder is set, and the heater lid is open, press the main switch to reset the holder base_ _position.__

__

| LED 3 is lit in RED

If the stripping conditions are not registered to the FH110 fiber holder, the LED will be lit RED.

The stripping operation will be executed according to the most recently selected stripping mode.

Main switch

Confirm the device status by checking the main switch, and then either start operation or reset the fiber holder base position.

__

__

OFF

| __

__

closed

| After resetting the holder base position, the next stripping operation can be started.
Before resetting the holder base position,

open the heater lid and remove the stripped fiber.

Set Up the Stripper

How to Replace the Blade

The SS110 is available with several different sizes of stripper blades that can be purchased as optional accessories.
Before starting operation, attach a stripper blade according to the size of the fiber to be stripped.

Remove the blade

1. Put the SS110 into maintenance mode and retract the fiber holder base.
2. Remove both the upper and lower blade screws with the included hex wrench. The stripper blades are identical, but the upper and lower blade screws are different. Do not re-install the blade screws in the wrong position.Store the stripper blades as pairs. Even if the stripper blades have the same coating/cladding diameters, the coating removal performance may deteriorate if the pairs are separated and used in combination with different stripping blades.

Attach the stripper blade

1. Confirm the blade size, and loosely attach both blades in the correct mounting position.
2. Tighten the lower blade screws with the hex wrench while pushing the stripper blade downward and backward.
3. Close the top cover and fully tighten the upper blade screws while the upper and lower blades are engaged.
4. Confirm that the stripping blades close with no gaps, and that there is no interference when opening and closing the top cover.

Heater height adjustment

This product is able to accommodate different fiber coating diameters by adjusting the height of the heating element. Adjusting the heat element height allows the fiber to be better aligned with the stripping blades.

How to adjust the heater height

Turning the adjustment screw on the right side of the device body will adjust the height of the heater.Match the height indicator to the diameter of the fiber coating being used.

After replacing the stripper blade, visually inspect to ensure the blades are installed correctly. Always perform the heater height adjustment when replacing the stripper blades to avoid fiber misalignment.?

Applicable fiber holder

Several different types of fiber holders can be used with the SS110. When using fiber holders, the fiber holder base must be sett up for each type of fiber holder. Applicable fiber holders

Positioning spacer
The location of the positioning spacer is different depending on the fiber holder. Change the positon of the spacer according to the fiber holder being used.

Fiber holder management (when using the FH110)

Only the FH110 series fiber holders are capable of configuring the stripping settings on the SS110. Other fiber holders do not have RFID capability and cannot take advantage of this feature.
If an FH110 is already registered, the stripper will recognize it and LED 3 will turn GREEN. The stripper will operate with the previously customized stripping settings.
If an FH110 fiber holder is not registered, LED 3 will turn RED. To register the FH110, use the provided software or switch over to regular Mode.

The setting value can be modified by connecting the stripper to a PC and using the provided software.

Fiber Holder Adapter Installation

The FH-70 series fiber holders can be used if the corresponding fiber holder adapter FH-70 is installed.

HEX-01 Hex wrench

Stripping Operation

Power Supply

1. Only use a genuine Fujikura AC adapter and AC power cord.
2. Plug in the AC cord and insert the AC cord into the AC plug of the ACC-**.
3. Plug the AC adapter cord into the power port of the stripper. Disconnect the AC power cord from the AC adapter or from the wall outlet immediately when mechanical or electrical problems occur with the stripper or AC adapter. Use the stripper in a place where you can quickly access to disconnect the power cord.

Turning Power ON/OFF

1. Remove any fiber before powering on the stripper.
   • If a fiber is on the fiber holder base when the SS110 is turned on, the fiber will hit the device body and break.
2. Slide the switch located on the right side of the device body to power on.
3. The holder base will move to its home position.

Stripping

Coating residue will remain in the stripping area after operation. Remove the coating residue before the next operation.

1. Load the fiber holder onto the fiber holder base. If the appropriate mode is not selected, press and hold the F2 key to switch modes.

2. Close and push the top cover downward until it locks, then press the main switch. Heating for stripping will start and main switch will be lit to indicate that the stripping operation is in progress.

3. After the fiber was heated for the specified time, the fiber holder base will automatically travel backward to remove the coating.
   When the stripping operation is finished, the main switch will blink 3 times.

4. Open the top cover and fiber holder clamp cover, then remove the fiber holder from the SS110.

5. Remove and clean the coating residue from the upper and lower blades with the included brush BRS-03.

6. Remove the coating residue from the heater, rubber pad, and small gaps with the opposite side of the brush BRS-03.
   Never leave coating residue under the fiber holder base.Always sweep toward the outside
   Use caution – the heater is very hot!

7. Pressing the main switch will return the fiber holder base to its home position.

Daily Maintenance

Clean the stripper blade, the surface of the heater, and the rubber pad with the brush BRS-03 after every stripping pass. Clean the stripper blades
Remove any coating residue from the upper and lower blades with the brush BRS-03.

Clean the heater
Remove any coating residue from the heater, rubber pad, and other small gaps with the opposite side of the brush BRS-03.Clean the stripping area with an alcohol- impregnated cotton swab after removing coating residue.

FCC

FCC notices (U.S. only) and other regulation information

The specialty fiber stripper SS110 uses RFID technology. Typical certification or regulations are below.

United States FCC

FCC ID: 2A9PZ-SS110
Contains FCC ID: QOQ-BGM220S2
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.

Canada ISED

IC: 29835-SS110
Contains IC: 5123A-BGM220S2

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.

Warranty and Contact Address

Warranty

Warranty period and limits

If the stripper becomes out of order within one year from the date of delivery, we will repair it free of charge. However, note that repairs will be charged for the following cases regardless of the warranty period:

1. Trouble or damage due to natural disaster.
2. Trouble or damage due to mishandling.
3. Trouble or damage due to handling in disregard of the operating procedures or instructions described in the instruction manual.
4. Consumable items (stripper blades etc.)

Note that memory contents such as stripper results may be lost depending on the kind of repair.

Necessary information needed for repair

Include all documentation with the stripper, and inform us of the details below:

1. Your full name, section, division, company, address, phone number, fax number, and e-mail address.
2. Model name and serial number of the stripper.
3. Description of problems encountered

Transporting the stripper

Since the Stripper is a high-precision machine, always use the original storage box for transportation and storage in order to protect it against humidity, vibration, and shock. When requesting repair, please send it, along with its accessories, in the original storage box.

Before shipping the stripper

Consult the authorized distributor before shipping.

Contact Address
Inquiries concerning products should be made to the nearest Fujikura authorized distributor or one of the following:

Fujikura Europe Ltd.

C51 Barwell Business Park
Leatherhead Road, Chessington, Surrey KT9 2NY, UK

General inquiries: +44-20-8240-2000
Service & support: +44-20-8240-2020
URL https://www.fujikura.co.uk

AFL

110 Hidden Lake Circle,
Duncan, SC, 29334, U.S.A.
P.O.Box 3127 Spartanburg, SC 29304-3127
General inquiries,
Service & support: +1-800-235-3423, Opt. 2
URL https://www.aflglobal.com

Fujikura Asia Ltd.

438A Alexandra Road, Block A Alexandra Techno Park #08-03, SINGAPORE, 119967
General inquiries,
service & support: +65-6-278-8955
URL https://www.fujikura.com.sg

Fujikura Ltd.

1-5-1 Kiba, Koto-ku, Tokyo 135-8512, Japan
General inquiries: +81-3-5606-1164
Service & support: +81-43-484-3962
URL https://www.fujikura.com

Fujikura (CHINA) Co., Ltd.

7thFloor, Shanghai Hang Seng Bank Tower, 1000 Lujiazui Ring Road, Pudong New Area, Shanghai 200120, CHINA
General inquiries,
Service & support: +86-21-6841-3636
URL https://www.fujikura.com.cn

References

• AFL - Fiber optic cable, transmission and substation accessories, outside plant equipment, connectors, fusion splicers, test and inspection equipment.
• Fujikura Europe Limited
• Fujikura Global | TOP
• _藤仓（中国）有限公司
• Fujikura |

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>