BEA 10ECA EAGLE Ceiling Adapter Instruction Manual

: June 13, 2024
: BEA

Table of Contents

BEA 10ECA EAGLE Ceiling Adapter
Product Information
Product Usage Instructions
CEILING ACCESSORY 10ECA
More Information
PRECAUTIONS
INSTALLATION
CAMERA TECHNICAL SPECIFICATIONS
QR SCAN
Contact
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEA 10ECA EAGLE Ceiling Adapter

Product Information

The product is a part of the EAGLE Family Accessories and includes the following items:

RAIN COVER 10ERC
RAIN ACCESSORY 10ERA
MOUNTING BRACKET 10EMB
CEILING ACCESSORY 10ECA
SPACER 10EAGLESPACER
EAGLE SPACER V 10EAGLESPACERV

The product is manufactured by BEA, Inc. and is intended for installation and setup in pedestrian doors or gates.

It is important to note the following precautions:

Maintain a clean and safe environment when working in public areas.
Be aware of pedestrian traffic around the door area.
Stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
Ensure compliance with all applicable safety standards upon completion of installation.

Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring compliance with local, national, and international regulations, codes, and standards.

The product installation and service technicians are recommended to be AAADM- certified for pedestrian doors, IDA-certified for doors/gates, and factory- trained for the type of door/gate system.
All appropriate industry signage, warning labels, and placards should be in place.

Product Usage Instructions

RAIN COVER 10ERC

To install the RAIN COVER 10ERC:

Align the RAIN COVER with the EAGLE and wall mounting holes.
Route the EAGLE Harness through the wall/header and then through the designated pass-thru on the spacer.
Mount the spacer to the wall/header using self-drilling screws.
Route the EAGLE Harness through the pass-thru on the sensor.
Mount the sensor to the accessory.
Wire the EAGLE Harness to the sensor.

CEILING ACCESSORY 10ECA

To install the CEILING ACCESSORY 10ECA:

Align the CEILING ACCESSORY with the EAGLE and wall mounting holes.
Mount the spacer to the wall/header using self-drilling screws.
Route the EAGLE Harness through the pass-thru on the sensor.
Mount the sensor to the accessory.
Wire the EAGLE Harness to the sensor.

More Information

BEA-10ECA-EAGLE-Ceiling-Adapter-fig-1

PRECAUTIONS

Maintain a clean and safe environment when working in public areas.
Constantly be aware of pedestrian traffic around the door area.
Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.

Reference EAGLE FAMILY User’s Guide (75.5957) for full EAGLE installation and setup.

INSTALLATION

BEA-10ECA-EAGLE-Ceiling-Adapter-fig-2

SPACER / SPACER V 10EAGLESPACER / 10EAGLESPACERV

Pre-drill the EAGLE Harness passage hole (1⁄4” for SPACER, 1⁄2” for SPACER V).
Route the EAGLE Harness through the wall/header and then through the designated pass-thru on the spacer.
Route the EAGLE SPACER V camera harness through the wall/header and then plug into SPACER V connector.
Mount the spacer to wall/header using self-drilling screws.
Route the EAGLE Harness through the pass-thru on the sensor.
Mount sensor to accessory.
Wire the EAGLE Harness to the sensor.

CAMERA TECHNICAL SPECIFICATIONS

Voltage regulator

(built into wire harness):

| 6.6 – 36 VDC (±10%)

6 – 28 VAC (±10%)

---|---
Operating temperature:| -30 – 60 °C (max. RH: 95%)
Video output:| 1.0 (Vp-p) / 75Ω
Image Sensor:| CMOS
Horizontal resolution:| 480 TVL
NTSC output:| 720 (H) × 480 (V)
Sync system:| Inter-Sync
Frame rate:| 30 fps
Min. illumination:| 0.01 LUX
AE control:| auto
Gain control:| auto
Elec. shutter:| 1 s ~ 1/10,000 s
S/N ratio:| > 50 dB
AWB:| auto

BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS

BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose.
BEA, Inc. strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/gates, and factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor/device system performance is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107, UL294, UL325, and International Building Code).
Verify that all appropriate industry signage, warning labels, and placards are in place.