Desoutter SH700-LR225-S90-A13S Angle Nutrunner User Manual

Desoutter SH700-LR225-S90-A13S Angle Nutrunner

Product Information

• Product Name: Angle Nutrunner
• Part Number: 2050505763
• Issue Number: 5
• Series Number: C
• Date: 12/2022
• Designed For: Installing and removing threaded fasteners in wood, metal, and plastic
• Intended Use: Professional use only
• Copyright: All rights reserved

Product Usage Instructions

Installation

1. Check the tightening torque given to the joint in question.
2. To adjust the tightening torque, follow these steps:
3. Turn the protection ring until the hole in the clutch housing is free.
4. Turn the outgoing spindle until you can see the keyhole in the adjustment washer.
5. Turn the adjustment key clockwise to decrease torque or anticlockwise to increase torque.
6. After adjustment, turn the protective ring back again.

WARNING: Never connect a part-assembled tool to the air supply. The rotor blades in this tool have a PTFE content. The normal health and safety recommendations concerning PTFE must be observed when handling these rotor blades.

Maintenance

For maximum performance, it is important to lubricate regularly. Follow these guidelines:

• Lubricate the motor with oil by dropping oil either into the compressed air or directly into the air inlet.
• Lubricate the trigger, planetary gears, needle bearings, and ball bearings with grease during regular machine overhaul.
• Lubricate the angle gear and clutch with grease that contains molybdenum disulphide, such as Molykote BR2 Plus or an equivalent brand.
• Use lubricants of good quality. Refer to the recommended lubricants mentioned in the table.

Note : The use of spare parts/accessories other than those originally supplied by the manufacturer may result in a drop in performance and/or increased maintenance/noise level/vibrations, and as a result, the full cancellation of the manufacturer’s liability.

WARNING
TO REDUCE THE RISK OF INJURY, BEFORE USING OR SERVICING TOOL, READ AND UNDERSTAND THE FOLLOWING INFORMATION AS WELL AS SEPARATELY PROVIDED SAFETY INSTRUCTIONS (ITEM NUMBER: 2050502163)

Copyright
© Copyright 2022, Desoutter HP2 7SJ UK. All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.

Statement of use

This product is designed for installing and removing threaded fasteners in wood, metal and plastic. No other use permitted. For professional use only. The use of spare parts/accessories other than those originally supplied by the manufacturer may result in a drop in performance and/or increased maintenance/noise level/vibrations, and as the result, the full cancellation of the manufacturer’s liability

WARNING
NEVER CONNECT A PART-ASSEMBLED TOOL TO THE AIR SUPPLY. THE ROTOR BLADES IN THIS TOOL HAVE A PTFE CONTENT. THE NORMAL HEALTH AND SAFETY RECOMMENDATIONS CONCERNING PTFE MUST BE OBSERVED WHEN HANDLING THESE ROTOR BLADES.

• DO NOT SMOKE.
• MOTOR COMPONENTS MUST BE WASHED WITH CLEANING FLUID AND NOT BLOWN CLEAR WITH AN AIR LINE.
• THE SILENCER MUST BE REPLACED WHEN DIRTY, DO NOT CLEAN AND RE-USE.
• WASH HANDS BEFORE COMMENCING ANY OTHER ACTIVITY

Installation

Air quality

• For optimum performance and maximum machine life we recommend use of compressed air with a dew point between +2°C and +10°C. Installation of a refrigeration-type air dryer is recommended.
• Use a separate air filter to remove solid particles larger than 30 microns and more than 90 % of water, installed as close as possible to the machine and prior to any other air preparation unit. Blow out the hose before connecting.
• The compressed air must contain a small quantity of oil. We strongly recommend that you install a oil-fog lubricator to be set normally at 3-4 drops(50mm3)/m3 air consumption for long cycle running tools, or a single-point lubricator for short cycle running tools.
• Regarding lubrication-free tools it is, at the customer’s option, no disadvantage if the compressed air contains a small quantity of oil as supplied from a lubricator. An exception is turbine tools that should be kept oil free. (For further information please see Air Line Accessories in our main catalog.)

Compressed air connection

• The machine is designed for a working pressure of 6–7 bar = 600–700 kPa = 87–102 psi.
• Blow out the hose before connecting.

Handling

Tightening torque

For accurate operation and safety, the tightening torque of the nut runner must be set correctly in relation to the screw joint. Check the tightening torque given to the joint in question.
The tightening torque is adjusted by altering the tension of the clutch spring. Turn the protection ring until the hole in the clutch housing is free. Then turn the out going spindle until you can see the keyhole in the adjustment washer. Turn the adjustment key clockwise to decrease and anticlockwise to increase the torque. After the adjustment, turn the protective ring back again.

Maintenance

• All torque figures ± 10%.
• When disposing of components, lubricants, etc …ensure that the relevant safety procedures are carried out.
• Overmold should be wiped clean with a general purpose, nonaggressive degreasant.

For maximum performance

• It is important to lubricate regularly to get maximum performance and trouble-free operation. The motor should be lubricated with oil; i.e. drops of oil can be dropped either into the compressed air or directly into the air inlet.
• The trigger, planetary gears, needle bearings and ball bearings should be lubricated with grease during the regular overhaul of the machine.
• The angle gear and clutch must be lubricated using grease that contains molybdenum disulphide: Molykote BR2 Plus, for ex-ample, or an equivalent brand.
• Use lubricants of good quality. The oils and greases mentioned in the table are examples of lubricants which are recommended.

Rust protection and internal cleaning
Water in the compressed air, dust and wear particles cause rust and sticking of vanes, valves etc. An air filter should be installed close to the machine (see “Air quality”).

Reporting, RE–signal
Reporting (RE) machines supply an air signal that can be connected to a monitoring instrument that counts the number of approved tightenings and detects premature shut-offs and rehits and other ir-regularities.

Service instructions

• Overhaul and preventive maintenance is recommended at regular intervals once per year or after a maximum 250.000 tightening depending on which occurs sooner. More frequent overhaul may be needed, if used at high torque and long tightening times. If the machine not is working properly, it should immediately be taken away for inspection.
• The strainer at the air inlet and the exhaust silencer should be cleaned frequently or replaced in order to prevent clogging, which decreases the capacity.
• At the overhauls, all parts should be cleaned accurately and de-fective or worn parts (i.e. O-rings, vanes) should be replaced.

Disassembling/assembling

It is important that the machine’s threaded connections are tightened properly; i.e. in accordance with the specifications on the exploded views.
Lubricate o-rings and threaded connections with grease before assembling.

• Cleaning
  Clean all parts thoroughly in white spirit or similar cleaning agent. To prevent clogging and decreased power, it could be necessary to clean the strainer (if used) and the exhaust filter between the overhauls.

• Inspection
  After the cleaning, inspect all parts. Damaged and worn parts should be replaced.

• Lubrication
  Lubricate specially gears, valve and clutch with grease containing molybdenum disulphide (e.g. Molykote BR2 Plus). Please see exploded views and fig. under Service instructions.

Grease Guide

Spare parts
Parts without ordering number are not delivered separately for technical reasons.
The use of other than genuine Desoutter replacement parts may result in decreased tool performance and increased maintenance and may, at the company option, invalidate all warranties.

Technical data

Rated speed and Torque range

Declaration of noise and vibration emission

• All values are current as of the date of this publication. For the latest information please visit www.desouttertools.com.These declared values were obtained by laboratory-type testing in accordance with the stated standards and are suitable for comparison with the declared values of other tools tested in accordance with the same standards. These declared values are not adequate for use in risk assessments and values measured in individual workplaces may be higher. The actual exposure values and risk of harm exper-ienced by an individual user are unique and depend upon the way the user works, the workpiece and the workstation design, as well upon the exposure time and the physical condition of the user.
• We, Desoutter, cannot be held liable for the consequences of using the declared values, instead of values reflecting the actual exposure, in an individual risk assessment in a workplace situation over which we have no control. This tool may cause hand-arm vibration syndrome if its use is not adequately managed. An EU guide to managing hand-arm vibration can be found at http://www.humanvibration.com/EU/VIBGUIDE.html We recommend a program of health surveillance to detect early symptoms which may relate to noise or vibration exposure, so that management procedures can be modified to help prevent future impairment.

EC DECLARATION OF CONFORMITY

We, Desoutter, 37 Mark road, Hemel Hempstead, Herts-UK, HP27BW, +44 (0) 1442 838999 declare under our sole responsibility that our product (with type and serial number, see front page) and in combination with our accessories, to which this declaration-relates is in conformity with the appropriate standard(s):

EN ISO 11148-6: 2010 and in accordance with the following directive(s): 2006/42/EC
Machinery DirectiveOrigin of the product: SwedenTechnical file available from EU headquater.CP 38 rue Bobby Sands – BP 1027344818 Saint Herblain –
France+33 (0) 2 40 80 20 00Saint Herblain, 20/06/2012B.Blanchet,
General Manager Signature of issuer

Desoutter Warranty

1. This Desoutter product is guaranteed against defective workmanship or materials, for a maximum period of 12 months following the date of purchase from Desoutter or its agents, provided that its usage is limited to single shift operation throughout that period. If the usage rate exceeds that of single shift operation, the warranty period shall be reduced on a pro rata basis.
2. If, during the warranty period, the product appears to be defective in workmanship or materials, it should be returned to Desoutter or its agents, together with a short description of the alleged defect. Desoutter shall, at its sole discretion, arrange to repair or replace free of charge such items as are deemed faulty by reason of defective workmanship or materials.
3. This warranty ceases to apply to products which have been abused, misused or modified, or which have been repaired using other than genuine Desoutter spare parts or by someone other than Desoutter or its authorized service agents.
4. Should Desoutter incur any expense correcting a defect resulting from abuse, misuse, accidental damage or unauthorized modification, they will require that such expense shall be defrayed in full.
5. Desoutter accepts no claim for labour or other expenditure made upon defective products.
6. Any direct, incidental or consequential damages whatsoever arising from any defect are expressly excluded.
7. This warranty is given in lieu of all other warranties, or conditions, expressed or implied, as to the quality, merchantability or fitness for any particular purpose.
8. No one, whether an agent, servant or employee of Desoutter, is authorized to add to or modify the terms of this limited warranty in any way.

Exploded views/tables

Service instructions

Tightening of threaded connections
The tightening torques indicated in the exploded views list are established to achieve the correct clamping force and preventing the parts from coming loose. At service these parts must be able to open up without being destroyed. In special circumstances (depending on application and usage) the parts may however come loose after some time of operation. In such cases the torque could be increased 10-20% and if necessary some type of low or medium threadlocking fluid could also be applied

Diagram, RE – signal

With the RE-signal Kit an air pressure signal will be supplied, which can be connected to a control unit to count the number of tightening and to detect premature and rehits.

Check of valve position

Instructions for vane motor

Static measurement / Dynamic measurement

EU DECLARATION OF CONFORMITY

We : Technical file available from EU headquarters. Ets Georges Renault 38 rue Bobby Sands – BP 10273 44818 Saint Herblain – France P.Roussy, R&D Manager Ets Georges Renault 38 rue Bobby Sands – BP 10273 44818 Saint Herblain – France declare under our sole responsibility that the product(s):  Machine type(s) : PNEUMATIC SCREWDRIVER

Origin of the product: Sweden is in conformity with the following UK Regulations: to “Supply of Machinery (Safety) Regulations 2008” Designated standard(s) applied : EN ISO 11148-6:2012
NAME and POSITION of issuer : Pascal ROUSSY ( R&D Manager)
Place & date : Saint-Herblain, 06/10/2022 UK Authorized Representative: Air Compressors & Tools Ltd Unit 5 Westway 21, Chesford Grange, Woolston, Warrington, WA1 4SZ UK
Contact : M.Taylor
www.desouttertools.com

References

• .com.de | Germany's new domain
• tools.com | Buy Power Tools and Automotive Parts online
• Web Page Under Construction
• Desoutter Industrial Tools - Industrial Pneumatic Tool for Aeronautics & Automotive
• HumanVibration.com is for sale | HugeDomains

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>