Desoutter SH70-LR1100-S90-A4S Angle Nutrunner User Manual
- June 13, 2024
- Desoutter
Table of Contents
Industrial Tools
Angle nutrunner
User manual, EC-declaration included
SH70-LR1100-S90-A4S
2051476284
WARNING – ATTENTION
TO REDUCE THE RISK OF INJURY, BEFORE USING OR SERVICING TOOL, READ AND UNDERSTAND THE FOLLOWING INFORMATION AS WELL AS SEPARATELY PROVIDED SAFETY INSTRUCTIONS (ITEM NUMBER: 2050502163)
SH70-LR1100-S90-A4S Angle Nutrunner
Copyright
© Copyright 2022, Desoutter HP2 7SJ UK. All rights reserved.
Any unauthorized use or copying of the contents or part thereof is prohibited.
This applies in particular to trademarks, model denominations, part numbers
and drawings. Use only authorized parts. Any damage or malfunction caused by
the use of unauthorized parts is not covered by Warranty or Product Liability.
Statement of use
This product is designed for installing and removing threaded fasteners in wood, metal and plastic. No other use permitted. For professional use only. The use of spare parts/accessories other than those originally supplied by the manufacturer may result in a drop in performance and/or increased maintenance/noise level/vibrations, and as the result, the full cancellation of the manufacturer’s liability.
Installation
Air quality
– For optimum performance and maximum machine life we recommend use of
compressed air with a dew point between
+2°C and +10°C. Installation of a refrigeration-type air dryer is recommended.
– Use a separate air filter to remove solid particles larger than 30 microns
and more than 90 % of water, installed as close as possible to the machine and
prior to any other air preparation unit. Blow out the hose before connecting.
– The compressed air must contain a small quantity of oil. We strongly
recommend that you install a oil-fog lubricator to be set normally at 3-4
drops(50mm³)/m³ air consumption for long cycle running tools, or a single-
point lubricator for short cycle running tools.
– Regarding lubrication free tools it is, at the customers option, no
disadvantage if the compressed air contains a small quantity of oil as
supplied from a lubricator. An exception is turbine tools that should be kept
oil free. (For further information please see Air Line Accessories in our main
catalogue.)
Compressed air connection
– The machine is designed for a working pressure of 6–7 bar = 600–700 kPa =
87–102 psi.
– Blow out the hose before connecting.
Handling
Tightening torque
For accurate operation and safety, the tightening torque of the nut runner
must be set correctly in relation to the screw joint. Check the tightening
torque given to the joint in question. The tightening torque is adjusted by
altering the tension of the clutch spring. Turn the protection ring until the
hole in the clutch housing is free. Then turn the out going spindle until you
can see the keyhole in the adjustment washer. Turn the adjustment key
clockwise to decrease and anticlockwise to increase the torque. After the
adjustment, turn the protective ring back again.
WARNING
NEVER CONNECT A PART ASSEMBLED TOOL TO THE AIR SUPPLY. THE ROTOR BLADES IN
THIS TOOL HAVE A PTFE CONTENT. THE NORMAL HEALTH AND SAFETY RECOMMENDATIONS
CONCERNING PTFE MUST BE OBSERVED WHEN HANDLING THESE ROTOR BLADES.
– DO NOT SMOKE.
– MOTOR COMPONENTS MUST BE WASHED WITH CLEANING FLUID AND NOT BLOWN CLEAR WITH
AN AIR LINE.
– THE SILENCER MUST BE REPLACED WHEN DIRTY, DO NOT CLEAN AND RE-USE.
– WASH HANDS BEFORE COMMENCING ANY OTHER ACTIVITY
Maintenance
– All torque figures ± 10%.
– When disposing of components, lubricants, etc …ensure that the relevant
safety procedures are carried out.
– Over mold should be wiped clean with a general purpose, nonaggressive
degreasant.
For maximum performance
It is important to lubricate regularly to get maximum performance and trouble-
free operation. The motor should be lubricated with oil; i.e. drops of oil can
be dropped either into the compressed air or directly into the air inlet.
The trigger, planetary gears, needle bearings and ball bearings should be
lubricated with grease during the regular overhaul of the machine.
The angle gear and clutch must be lubricated using grease that contains
molybdenum disulphide: Moly kote BR2 Plus, for example, or an equivalent
brand.
Use lubricants of good quality. The oils and greases mentioned in the table
are examples of lubricants which are recommended.
Rust protection and internal cleaning
Water in the compressed air, dust and wear particles cause rust and sticking
of vanes, valves etc. An air filter should be installed close to the machine
(see “Air quality”).
Reporting, RE – signal
Reporting (RE) machines supply an air signal that can be connected to a
monitoring instrument that counts the number of approved tightening and
detects premature shut-off and rehits and other irregularities.
Service instructions
Overhaul and preventive maintenance is recommended at regular intervals once
per year or after maximum 250.000 tightening depending on which occurs sooner.
More frequent overhaul may be needed, if used at high torque and long
tightening times. If the
machine not is working properly, it should immediately be taken away for
inspection.
The strainer at the air inlet and the exhaust silencer should be cleaned
frequently or replaced in order to prevent clogging, which decreases the
capacity.
At the overhauls, all parts should be cleaned accurately and defective or worn
parts (i.e. O-rings, vanes) should be replaced.
Disassembling/assembling
It is important that the machines threaded connections are tightened properly;
i.e. in accordance with the specifications on the exploded views.
**** Lubricate o-rings and threaded connections with grease before assembling.
Cleaning
Clean all parts thoroughly in white spirit or similar cleaning agent.
To prevent clogging and decreased power, it could be necessary to clean the
strainer (if used) and the exhaust filter between the overhauls.
Inspection
After the cleaning, inspect all parts. Damaged and worn parts should be
replaced.
Lubrication
Lubricate specially gears, valve and clutch with grease containing molybdenum
disulphide (e.g. Molykote BR2 Plus). Please see exploded views and fig. under
Service instructions.
Grease Guide
Brand| General purpose Bearings| Motor shaft| Air
Lubrication
---|---|---|---
BP| Spheerol EP L2| | Energol E46
Castrol| Energrease LS-EP2| |
Esso| Beacon EP2| | Arox EP46
Q8| Rembrandt EP2| | Chopin 46
Mobil| Mobilegrease XHP
222| | Almo oil 525
Shell| Alvania EP2| | Aries 32
Texaco| Multifak EP2| | Tonna R32
Molycote| | BR2 Plus|
Lubricating
Engineers| | Almagard3752|
Spare parts
Parts without ordering number are not delivered separately for technical
reasons.
The use of other than genuine Desoutter replacement parts may result in
decreased tool performance and increased maintenance and may, at the company
option, invalidate all warranties.
Technical data
Rated speed and Torque range
Rated speed (Rpm) | 2.5-7 |
---|---|
Torque range (Nm) | 1100 |
Noise and vibration emission
Noise (according to EN ISO 15744) | dB(A) |
---|
Measured sound pressure level
Determined sound power level| 80
Spread in method and production| 3
Vibration (according to ISO 8662-7)| m/s²
Measured vibration value| <2.5
Spread in method and production| –
Declaration of noise and vibration emission
All values are current as of the date of this publication. For the latest
information please visit www.desouttertools.com.These declared values were
obtained by laboratory type testing in accordance with the stated standards
and are suitable for comparison with the declared values of other tools tested
in accordance with the same standards. These declared values are not adequate
for use in risk assessments and values measured in individual work places may
be higher. The actual exposure values and risk of harm experienced by an
individual user are unique and depend upon the way the user works, the
workpiece and the workstation design, as well upon the exposure time and the
physical condition of the user.
We, Desoutter, cannot be held liable for the consequences of using the
declared values, instead of values reflecting the actual exposure, in an
individual risk assessment in a work place situation over which we have no
control. This tool may cause hand-arm
vibration syndrome if its use is not adequately managed. An EU guide to
managing hand-arm vibration can be found at
http://www.humanvibration.com/EU/VIBGUIDE.htm We recommend a programme of
health surveillance to detect early symptoms which may relate to noise or
vibration exposure, so that management procedures can be modified to help
prevent future impairment.
EC DECLARATION OF CONFORMITY
We, Desoutter, 37 Mark road, Hemel Hempstead, Herts-UK, HP27BW, +44 (0) 1442
838999 declare under our sole responsibilitythat our product (with type and
serial number, see front page) andin combination with our accessories, to
which this declaration-relates is in conformity with the appropriate
standard(s):
EN ISO 11148-6: 2010 and in accordance with the following directive(s):
2006/42/EC
Machinery Directive Origin of the product: Sweden Technical file available
from EU head quater.CP
38 rue Bobby Sands – BP 1027344818 Saint Herblain France+33 (0) 2 40 80 20
00Saint Herblain, 20/06/2012B.Blanchet,
General Manager
Signature of issuer
Desoutter Warranty
- This Desoutter product is guaranteed against defective workmanship or materials, for a maximum period of 12 months following the date of purchase from Desoutter or its agents, provided that its usage is limited to single shift operation throughout that period. If the usage rate exceeds that of single shift operation, the warranty period shall be reduced on a pro rata basis.
- If, during the warranty period, the product appears to be defective in workmanship or materials, it should be returned to Desoutter or its agents, together with a short description of the alleged defect. Desoutter shall, at its sole discretion, arrange to repair or replace free of charge such items as are deemed faulty by reason of defective workmanship or materials.
- This warranty ceases to apply to products which have been abused, misused or modified, or which have been repaired using other than genuine Desoutter spare parts or by someone other than Desoutter or its authorized service agents.
- Should Desoutter incur any expense correcting a defect resulting from abuse, misuse, accidental damage or unauthorized modification, they will require that such expense shall be defrayed in full.
- Desoutter accepts no claim for labour or other expenditure made upon defective products.
- Any direct, incidental or consequential damages whatsoever arising from any defect are expressly excluded.
- This warranty is given in lieu of all other warranties, or conditions, expressed or implied, as to the quality, merchantability or fitness for any particular purpose.
- No one, whether an agent, servant or employee of Desoutter, is authorized to add to or modify the terms of this limited warranty in any way.
Exploded views/tables
Angle head
Ref. No.| Ordering No.| Qty| Description| Remark /
Included in Service kit
---|---|---|---|---
1(2-21)| 2050 5161 93| 1| Angle head, compl.| i=1, 1/4″sq
2| 2050 5151 63| 1| Nut|
3| 2050 5151 73| 1| Ball bearing| 609
4| 2050 5038 33| 1| Nut|
5| 2050 5151 83| 1| Intermediate part|
6(7-9)| 2050 5151 93| 1| Pinion shaft, compl.|
7| 2050 5152 03| 1| Pinion shaft|
8| 2050 5152 13| 1| Ball bearing| 618/9
9| 2050 5152 23| 1| Bevel gear|
10| 2050 5152 33| 1| Angle head|
11(12-19)| 2050 5142 03| 1| Spindle, compl.|
12| 2050 5152 43| 1| Needle bearing| BK0408TN
13(14-16)| 2050 5152 53| 1| Spindle, compl.|
14| 2050 5152 23| 1| Bevel gear|
15| 2050 5152 13| 1| Ball bearing| 618/9
16| 2050 5152 63| 1| Spindle|
17(18-19)| 2050 5142 13| 1| Retainer pin kit|
18| –| 1| Spring|
19| 4210 2369 02| 1| |
20| –| 1| O-ring| 12.1×1.6 / Service kit 2050 5141 63
21| 2050 5152 73| 1| Nut|
Clutch casing and gears
Ref. No.| Ordering No.| Qty| Description| Remark /
Included in Service kit
---|---|---|---|---
1(2-3)| 2050 5142 23| 1| Driver, compl.|
2| –| 1| O-ring| 15×1 / Service kit 2050 5141 63
3| –| 1| Driver|
4| 2050 5142 33| 1| Clutch|
5| –| 1| Stop pin| Service kit 2050 5141 63
6| –| 1| Spring| Service kit 2050 5141 63
7(8-10)| 2050 5142 43| 1| Coupling ring, compl.|
8| –| 3| Roller| Service kit 2050 5141 63
9| –| 1| Ring|
10| –| 1| Coupling ring|
11| 2050 5157 73| 1| Guide ring|
12| 2050 5106 83| 1| Clutch spring|
13(14-15)| 2050 5142 53| 1| Adjustment kit|
14| –| 1| Adjustment washer|
15| –| 1| Interlocking disc|
16| 2050 5038 23| 1| Protective ring|
17| 2050 5107 93| 1| Lock ring| I 28×1.2V
18| 2050 5107 83| 1| Ball bearing| 6001-Z
19(20-25)| 2050 5142 63| 1| Planetary gear| i = 3.25
20| 2050 5100 23| 1| Circlip| SgA12
21| –| 1| Planet shaft|
22| 2050 5107 63| 1| Spring|
23| 2050 5105 23| 1| Washer|
24| 2050 5107 53| 1| Circlip| Sgh9
25| 2050 5157 63| 3| Gear wheel| z = 12
26| 2050 5037 93| 1| Casing| z = 45
27| 2050 5157 53| 1| Washer|
28(29-31)| 2050 5142 73| 1| Planetary gear| i = 4,46
29| –| 1| Planet shaft| z = 20
30| 2050 5157 43| 3| Needle bearing| K3x5x7TN
31| 2050 5157 33| 3| Gear wheel| z = 15
32| 2050 5157 23| 1| Washer|
33| 2050 5157 13| 1| Gear wheel| z = 13/7
34| 2050 5078 53| 1| Adjustment key| Accessory included
Motor
Ref. No.| Ordering No.| Qty| Description| Remark /
Included in Service kit
---|---|---|---|---
1(2-12)| 2050 5159 23| 1| Motor, compl.|
2| –| 1| Ball bearing| 625-Z / Service kit 2050 5141 63
3| –| 1| Retainer pin| Service kit 2050 5141 63
4| –| 1| Spring| Service kit 2050 5141 63
5| 2050 5159 33| 1| End plate|
6| 4498 03| 1| Pin| CP2x6
7| 2050 5159 43| 1| Cylinder|
8| 2050 5159 53| 1| Rotor| z = 7
9| 2050 5342 03| 1| Vane kit| 5 pcs
10| 4501 33| 1| Key| RK2x2x10
11| 2050 5159 63| 1| End plate|
12| –| 1| Ball bearing| 607 / Service kit 2050 5141 63
13| 2050 5159 73| 2| Cup spring| 28×12.2×1
Motor casing and shut off valve
Ref. No.| Ordering No.| Qty| Description| Remark /
Included in Service kit
---|---|---|---|---
1| 2050 5109 23| 1| Spacer| 26x30x0.3
2| 2050 5109 33| 1| Circlip| SgH16
3(4-6)| 2050 5141 73| 1| Valve, compl.|
4| –| 1| Valve|
5| –| 1| Spring| Service kit 2050 5141 63
6| –| 1| Washer| BRB2.2×4.5 / Service kit 2050 5141 63
7(8-13)| 2050 5141 83| 1| Reversing valve, compl.|
8| 2050 5031 43| 1| Reversing ring|
9| 2050 5109 53| 1| Pin| CP3x10
10| –| 2| O-ring| 23.5×1 / Service kit 2050 5141 63
11| –| 1| O-ring| 10.4×1 / Service kit 2050 5141 63
12| –| 1| O-ring| 2×1 / Service kit 2050 5141 63
13| –| 1| Reversing valve|
14| 2050 5159 83| 1| Valve seat|
15| 2050 5161 73| 1| Motor casing|
16| 2050 5160 03| 1| Silencer|
Back head and silencer
Ref. No.| Ordering No.| Qty| Description| Remark /
Included in Service kit
---|---|---|---|---
1(2-3)| 2050 5139 93| 1| Adapter, compl.| With NPT-thread (for the US and
Canada) 2050 5140 03
2| –| 1| Adapter| G 1/4″
3| 2050 5109 93| 1| O-ring| 11.1x 1.6
4| 2050 5031 73| 1| Distributor|
5(6-8)| 2050 5141 93| 1| Silencer, compl.|
6| –| 1| Filter| Service kit 2050 5141 63
7| –| 2| Silencer|
8| 4507 23| 2| O-ring| 32.1x 1.6
9(10-11)| 2050 5140 23| 1| Adapter, compl.|
10| –| 1| Adapter|
11| 2050 5110 33| 1| O-ring| 17.5x 1.3
12(13-15)| 2050 5140 33| 1| Valve, compl.|
13| –| 1| Strainer| Service kit 2050 5141 63
14| 2050 5110 43| 1| Spring|
15| –| 1| Valve|
16| 2050 5110 53| 1| Ring|
17| 2050 5110 63| 1| Screw| M5x5
18| 2050 5031 53| 1| Back head, compl.|
19| –| 1| O-ring| 17.5×1.3(Also incl. in Reversing valve 2050 5141 83) /
Service kit 2050 5141 63
20(21-23)| 2050 5140 43| 1| Lever, compl.|
21| 2050 5110 83| 1| Pin|
22| –| 1| Lever|
23| 2050 5110 93| 1| Pin| 2.5×22
Optional accessories
RE – kit
Ref. No.| Ordering No.| Qty| Description| Remark /
Included in Service kit
---|---|---|---|---
1(2-6)| 2050 1142 42| 1| Kit, RE-signal|
2| 2050 5088 83| 1| Hose|
3| 2050 5111 03| 1| Filter|
4| 2050 5160 13| 2| Silencer|
5| 4507 23| 1| O-ring| 32.1×1.6
6| 2050 5111 23| 1| Lock ring|
Exhaust hose
Ref. No.| Ordering No.| Qty| Description| Remark /
Included in Service kit
---|---|---|---|---
1| 4598 13| 1| Exhaust hose|
Suspention yoke
Ref. No.| Ordering No.| Qty| Description| Remark /
Included in Service kit
---|---|---|---|---
1| 2050 5163 23| 1| Suspention yoke, compl.|
Protective cover
Ref. No.| Ordering No.| Qty| Description| Remark /
Included in Service kit
---|---|---|---|---
1| 2050 1142 62| 1| Protective cover|
Service Kits
Service Kit (2050 5141 63)
Ordering No. 2050 5141 63
Ordering No.| Qty| Description| Remark / Included in Service
kit
---|---|---|---
–| 1| Washer| 2,2×4,5 FZ
–| 1| Ball bearing| 607-2Z
–| 1| Ball bearing| 625-2Z
–| 1| O-ring| 2×1
–| 1| O-ring| 13×1,2
–| 1| O-ring| 17,5×1,3
–| 1| O-ring| 15×1
–| 1| O-ring| 12,1×1,6
–| 1| O-ring| 18,1×1,6
–| 1| O-ring| 12,5×1,1
–| 1| O-ring| 10,4×1
–| 2| O-ring| 23,5×1
–| 1| Spring|
–| 1| Strainer|
–| 1| Spring|
–| 3| Roller|
–| 1| Catch|
–| 1| Catch|
–| 5| Vane|
–| 2| Filter|
–| 1| Spring|
–| 1| Tap|
Kit for a variety of products. Some parts might remain unused.
Service instructions
Tightening of threaded connections
The tightening torques indicated in the exploded views list are established to
achieve the correct clamping force and preventing the parts from coming loose.
At service these parts must be able to open up without being destroyed. In
special circumstances (depending on application and usage) the parts may
however come loose after some time of operation. In such cases the torque
could be increased 10-20% and if necessary some type of low or medium
threadlocking fluid could also be applied.
Example
Diagram, RE – signal
With the RE-signal Kit an air pressure signal will be supplied, which can be
connected to a control unit to count the number of tightening and to detect
premature and rehits.
Check of valve position
Instructions for vane motor
Dismantling
Inspection and lubrication
(R) = To be replaced at every overhaul (included in Service Kit)
Assembly
Static measurement / Dynamic measurement
Joint Simulator for Static Transducer
Part Number| Model| Transducer| Thread|
---|---|---|---|---
615 910 927 0| ACS5.01| ST4001| M5
615 910 928 0| ACS6.05| ST4005| M6
615 910 929 0| ACS6.10| ST4010| M6
615 910 930 0| ACS8.05| ST4005| M8
615 910 931 0| ACS8.10| ST4010| M8
615 910 932 0| ACS10.10| ST4010| M10
615 910 933 0| ACS10.50| ST4050| M10
615 910 934 0| ACS10.50| ST4050| M12
615 910 935 0| ACS10.50| ST4050| M16
Stationary Transducer
Part Number| Model| Torque Range Nm| Torque Range
ft.lb
615 165 141 0| ST4001| 1-15| 0,7-11,1
615 165 142 0| ST4005| 5-70| 3,7-51,6
615 165 143 0| ST4010| 10-150| 7,4-110,5
615 165 144 0| ST4050| 50-700| 36,8-516
In Static as well as Dynamic measurement, it is advised to double check by the
use of a Dial Indicating Torque Wrench* (direct reading) or a Torsion Static
Torque Wrench** (connected to the Delta 4000 or Sigma 2001).
For further information regarding our complete measurement range, see our
general catalogue.
Torque Transducer
Part Number| Model| Torque Range Nm| Torque Range
ft.lb
---|---|---|---
615 165 211 0| DRT 4 H 20| 1,5-20| 1,11-14,7
615 165 212 0| DRT 4 Sq 20| 1,5-20| 1,11-14,7
615 165 213 0| DRT 4 Sq 25| 1,8-25| 1,33-18,4
615 165 214 0| DRT 4 Sq 75| 5,0-75| 3,69-55,3
615 165 215 0| DRT 4 Sq 180| 12,0-180| 8,85-132
615 165 216 0| DRT 4 Sq 500| 35,0-500| 25,8-368
**Dial Indicating Torque Wrenches***
| | Torque| Torque Range imper-
Part Number| Model| Range metric| ial
81972| TW-13| 0,5-13,5 Nm| 4-120 lbf in
81982| TW-27| 1-27 Nm| 1-20 lbf ft
81992| TW-80| 6-80 Nm| 5-60 lbf ft
82002| TW-160| 10-160 Nm| 7,4-120 lbf ft
Torsion Static Torque Wrenches**
Part Number| Model| Torque Range metric| Torque Range
imperial
615 165 146 0| CD4001| 1-15 Nm| 0,7-11 lbf in
615 165 147 0| CD4005| 5-70 Nm| 3,7-51,6 lbf ft
615 165 148 0| CD4010| 10-150 Nm| 7,4-110,5 lbf ft
615 165 149 0| CD4050| 50-700 Nm| 36,8-516 lbf ft
615 165 150 0| CD4101| 100-1500 Nm| 73,7-1105 lbf ft
(1)EU DECLARATION OF CONFORMITY
**** Doc No. 2050505983
Issue No. 06
(2) We :
Ets Georges Renault
38 rue Bobby Sands – BP 10273
44818 Saint Herblain – France
(3) Technical file available from EU headquarter.
P.Roussy, R&D Manager
Ets Georges Renault
38 rue Bobby Sands – BP 10273
44818 Saint Herblain – France
PNEUMATIC SCREWDRIVER
4) declare under our sole responsibility that the product(s):
(5) Machine type(s) :
SH850-LR190-S90-A13S
SH1200-LR215-S90-A13S
SH70-LR1100-S90-A4S
SH150-LR580-S90-A10S
SH200-LR550-S90-A10S
SH280-LR350-S90-A10S
SH280-LR80-S90-A10S
SH420-LR400-S90-A10S
SH2000-LR100-S90-A13S
SH470-LR350-S
SH280-LR350-S90-A10S-DU
SH420-LR400-S90-A10S-DU
SH500-LR330-S90-A10S-DU
SH700-LR225-S90-A13S-DU
SH850-LR190-S90-A13S-DU
SH1200-LR215-S90-A13S-DU
SH2000-LR100-S90-A13S-DU| P/N
2051474754
2051474764
2051476284
2051476294
2051476304
2051476314
2051476324
2051478004
2051478014
2051478124
6150601330
6150601340
6150601350
6150601360
6150601370
6150601380
6150601390
---|---
(6) Origin of the product : Sweden
(7) is in conformity with the requirements of the council Directives on the
approximation of the laws of the Member States relating :
(8) to “Machinery” 2006/42/EC (17/05/2006)
(11) applicable harmonized standard(s) :
(12) NAME and POSITION of issuer :
(13) Place & Date : Saint-Herblain, 12/07/2022
EN ISO 11148-6:2012
Pascal ROUSSY
( R&D Manager)
UKCA DECLARATION OF
CONFORMITY
**** Doc No. 6159964370
Issue No. 04
We :
Ets Georges Renault
38 rue Bobby Sands – BP 10273
44818 Saint Herblain – France
Technical file available from EU headquarter.
P.Roussy, R&D Manager
Ets Georges Renault
38 rue Bobby Sands – BP 10273
44818 Saint Herblain – France
PNEUMATIC SCREWDRIVER
declare under our sole responsibility that the product(s):
Machine type(s) :
SH850-LR190-S90-A13S
SH1200-LR215-S90-A13S
SH70-LR1100-S90-A4S
SH150-LR580-S90-A10S
SH200-LR550-S90-A10S
SH280-LR350-S90-A10S
SH280-LR80-S90-A10S
SH420-LR400-S90-A10S
SH2000-LR100-S90-A13S
SH470-LR350-S
SH280-LR350-S90-A10S-DU
SH420-LR400-S90-A10S-DU
SH500-LR330-S90-A10S-DU
SH700-LR225-S90-A13S-DU
SH850-LR190-S90-A13S-DU
SH1200-LR215-S90-A13S-DU
SH2000-LR100-S90-A13S-DU| P/N
2051474754
2051474764
2051476284
2051476294
2051476304
2051476314
2051476324
2051478004
2051478014
2051478124
6150601330
6150601340
6150601350
6150601360
6150601370
6150601380
6150601390
---|---
Origin of the product : Sweden is in conformity with the following UK Regulations : to “Supply of Machinery (Safety) Regulations 2008”
Designated standard(s) applied :
NAME and POSITION of issuer :
Place & date : Saint-Herblain, 06/10/2022
EN ISO 11148-6:2012
Pascal ROUSSY
( R&D Manager)
UK Authorized Representative : Air Compressors & Tools Ltd
Unit 5 Westway 21,
Chesford Grange, Woolston,
Warrington, WA1 4SZ
UK
Contact : M. Taylor
References
- .com.de | Germany's new domain
- tools.com | Buy Power Tools and Automotive Parts online
- Web Page Under Construction
- Desoutter Industrial Tools - Industrial Pneumatic Tool for Aeronautics & Automotive
- HumanVibration.com is for sale | HugeDomains
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>