STAIRVILLE DDC-12 LCD DMX Controller User Manual
- June 5, 2024
- STAIRVILLE
Table of Contents
DDC-12 LCD DMX Controller
User Manual
MUSIC IS O UR PASSION
General information
This user manual contains important information on the safe operation of the
device. Read and follow all safety notes and all instructions. Save this
manual for future reference. Make sure that it is available to all persons
using this device. If you sell the device to another user, be sure that they
also receive this manual.
Our products and user manuals are subject to a process of continuous
development. We, therefore, reserve the right to make changes without notice.
Please refer to the latest version of the user manual which is ready for
download under www.thomann.de.
Further information
On our website (www.thomann.de) you will find lots of further information and details on the following points:
| Download | This manual is also available as a PDF file for you to download. |
|---|---|
| Keyword search | Use the search function in the electronic version to find the |
topics of interest for you quickly.
Online guides| Our online guides provide detailed information on technical
basics and terms.
Personal consultation| For a personal consultation please contact our
technical hotline.
Service| If you have any problems with the device the customer service will
gladly assist you.
Notational conventions
This manual uses the following notational conventions:
Letterings: The letterings for connectors and controls are marked by
square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
Symbols and signal words
In this section, you will find an overview of the meaning of symbols and signal words that are used in this manual.
| Signal word | Meaning |
|---|---|
| DANGER! |
This combination of symbol and signal word indicates an immediately dangerous situation that will result in death or serious injury if it is not avoided.
NOTICE!|
This combination of symbol and signal word indicates a possible dangerous situation that can result in material and environmental damage if it is not avoided.
Warning signs| Type of danger
| Warning – danger zone.
Safety instructions
Intended use
This device is used to control spotlights, dimmers, lighting effects
equipment or other DMXcontrolled devices. Use the device only as described in
this user manual. Any other use or use under other operating conditions is
considered to be improper and may result in personal injury or property
damage. No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sufficient physical, sensorial,
and intellectual abilities and having corresponding knowledge and experience.
Other persons may use this device only if they are supervised or instructed by
a person who is responsible for their safety.
Safety
DANGER!
The danger for children
Ensures that plastic bags, packaging, etc. are disposed of properly and are
not within reach of babies and young children. Choking hazard! Ensure that
children do not detach any small parts (e.g. knobs or the like) from the unit.
They could swallow the pieces and choke! Never let children unattended use
electrical devices.
NOTICE!
Risk of fire
Do not block areas of ventilation. Do not install the device near any direct
heat source. Keep the device away from naked flames.
NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy
dirt, and strong vibrations. NOTICE!
External power supply
The device is powered by an external power supply. Before connecting the
external power supply, ensure that the input voltage (AC outlet) matches the
voltage rating of the device and that the AC outlet is protected by a residual
current circuit breaker. Failure to do so could result in damage to the device
and possibly the user. Unplug the external power supply before electrical
storms occur and when the device is unused for long periods of time to reduce
the risk of electric shock or fire.
NOTICE!
Risk of fire due to the incorrect polarity
Incorrectly inserted batteries may destroy the device or the batteries. Ensure
that proper polarity is observed when inserting batteries.
NOTICE!
Possible damage by leaking batteries
Leaking batteries can cause permanent damage to the device. Take batteries out
of the device if it is not going to be used for a longer period.
Features
Special features of this 12-channel DMX controller
- 12 channel faders
- Master fader
- Compact design
- Simple operation
- Power adapter included
Starting up
Unpack and check carefully there is no transportation damage before using the
unit. Keep the equipment packaging. To fully protect the product against
vibration, dust, and moisture during transportation or storage use the
original packaging or your own packaging material suitable for transport or
storage, respectively.
Create all connections while the device is off. Use the shortest possible
high-quality cables for all connections. Take care when running the cables to
prevent tripping hazards. Power supply
You can use either a 9-V battery or the 9-V connector for an external power
supply. Before connecting check for correct polarity.
Changing the battery
To insert or change the battery, switch off the device first and disconnect
the power adapter from the device. Loosen the screws located at the four edges
of the base plate. Do not loosen the three screws in the middle of the base
plate. Carefully remove the base plate. Take care not to damage the cables.
Change the battery. Remount the base plate without squeezing the cables.
Insert and tighten the screws.
When a battery is inserted, a 9-V external power adapter must not be connected!
**NOTICE!**
**Possible data transmission errors**
For error-free operation make use of dedicated DMX cables and do not use ordinary microphone cables. Never connect the DMX input or output to audio devices such as mixers or amplifiers.
`` Connections in DMX mode
Connect the DMX input of the device to the DMX output of a DMX controller or
another DMX device. Connect the output of the first DMX device to the input of
the second one, and so on to form a daisy chain. Always ensure that the output
of the last DMX device in the daisy chain is terminated with a resistor (110
Ω, ¼ W).
Connections and controls
Top view
-
[POWER]
Power indicator. -
[MASTER]
Master fader.
The master fader controls all channels simultaneously. -
[1] … [12]
Channel faders 1 through 12.
The channel faders allow up to twelve DMX channels to be controlled individually. In the device software, assign each connected DMX device a channel in accordance with its position in the daisy chain: first device = 1 … last device = 12.
Rear panel -
[DMX OUT] DMX output.
-
[POWER] Main switch. Turns the device on and off.
-
[DC INPUT] Connecting socket for power supply unit.
Technical specifications
| Control protocols | DMX512 |
|---|---|
| Number of DMX channels | 12 |
| Input connections | Power supply |
| Output connections | DMX control |
| Power supply | External power adapter, 100 – 240 V 50/60 Hz |
9-V battery 6LR61 or 6LF22
Operating voltage Dimensions (W × H × D)| 9 V / 100 mA, center positive
301 mm × 50 mm × 155 mm (w/o faders) 301 mm × 65 mm × 155 mm (w/ faders)
Weight| 1.2 kg
Ambient conditions| Temperature range| 0 °C…40 °C
Relative humidity| 20 %…80 % (non-condensing)
Plug and connection assignment
Introduction
This chapter will help you select the right cables and plugs to connect your
valuable equipment so that a perfect light experience is guaranteed. Please
take our tips, because especially in ‘Sound & Light’ caution is indicated:
Even if a plug fits into a socket, the result of an incorrect connection may
be a destroyed DMX controller, a short circuit or ‘just’ a not working light
show!
DMX connections
The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX
input. Please refer to the drawing and table below for the pin assignment of a
suitable XLR plug.
| Pin | Configuration |
|---|---|
| 1 | Ground, shielding |
| 2 | Signal inverted (DMX–, ‘cold signal’) |
| 3 | Signal (DMX+, ‘hot signal’) |
Protecting the environment
Disposal of the packaging material For the transport and protective
packaging, environmentally friendly materials have been chosen that can be
supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but
make sure that they are fed to a recovery. Please follow the notes and
markings on the packaging. Disposal of batteries Batteries must not be
disposed of as domestic waste or thrown into the fire. Dispose of the
batteries according to national or local regulations regarding hazardous
waste. To protect the environment, dispose of empty batteries at your retail
store or at appropriate collection sites.
Disposal of your old device This product is subject to the European Waste
Electrical and Electronic Equipment Directive (WEEE) in its currently valid
version. Do not dispose of your normal household waste.
Dispose of this device through an approved waste disposal firm or through your
local waste facility. When discarding the device, comply with the rules and
regulations that apply in your country. If in doubt, consult your local waste
disposal facility.
Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
E-mail: info@thomann.de
Internet: www.thomann.de
08.04.2021, ID: 258125 (V3)