TETOTE B0C5XMK3ST 60×36 Bathroom LED Mirror Instruction Manual

TETOTE B0C5XMK3ST 60×36 Bathroom LED Mirror

PRODUCT SPECIFICATION

CONTACT US

• Note: After opening the package, Please inspect the product immediately for damage in transit or missing parts.
• If there is any missing, please contact us at (sales@tetote-tech.com) or you can contact us at Amazon by following these steps:
• Open “Orders” at Amazon
• Find the product you have purchased and open the product page
• Click Sold by “tote” -Click”Ask a question”
• Click “An order I have placed”
• Click “Your product” -Click “Other” -Click “Troubleshooting”
• Then you can send us messages, and we will reply within 24 hours.

Packing list

Manufacturer warranty for 2 years from the date of purchase.

USE INSTRUCTION

1. Please use in a safe voltage range. (100V-120V)
2. Use electrical tape to wrap around the wires to prevent leakage.
3. Do not strike mirror glass with hard or pointed items.

• DANGER: Before installation, make sure the main power is cut off.
• WARNING: Installation must be performed by a qualified licensed electrician.

BEFORE INSTALLATION

Note: Thank you very much for using tote products, to facilitate the use of tote products, please read this instruction carefully before you begin the installation.

1. Important Safety Instructions:
   • Please read all instructions carefully before assembling the item.
   • Assembly by two or more adults is highly recommended.
   • To connect the wires to the electrical junction box, a qualified technician or electrician is highly recommended.
   • Disconnect power before installing, adding, or changing any components.
   • Ensure that the fixing location can take the weight of the complete fitting.
   • To prevent injury, the mirror must be installed according to these instructions.
2. Pre-assembly:
   • After opening the package, inspect the product immediately upon receipt for transit damage or missing parts.
   • Keep the voltages between 100V and 120V. If the voltage exceeds 120V, please use a transformer.
   • You can connect the wires directly to your junction box or the plug.
3. Before installation, please check to make sure the mirror is working properly:
   • The left button is the anti-fog touch.
   • In order to prevent wasting energy, the defogging function will automatically turn off after 1 hour.
   • The middle button is the color temperature touch
   • The first touch is white light, the second touch is yellow light, the third touch is natural light, and so on.
   • Press and hold it to infinitely adjust the color temperature.
   • The right button is the light touch
   • The first touch is to turn on all the lights, the second touch is to turn on only the front lights, the third touch is to turn on only the backlights, and the touch again turns off all the lights, and so on.
   • Press and hold it to infinitely adjust the brightness.
   • If no button is pressed within 15 seconds, pressing again will turn the light off immediately.
   • Memory Function: The current setting of the mirror will be saved.
   • When you turn on the mirror next time, it will be in the same settings as it was.

INSTALLATION

Installation tools

• Note: Before installation, please confirm the position of the mirror hanging hole.
• The first line is the hole position distance. Before punching, please confirm that the hole position of the positioning ruler is consistent with the hanging hole of the product.
• The second line is the product size. Find the position of the corresponding hole according to the product width of the selected suspension mode.
• Choose the hanging method according to your preference, use the positioning ruler to confirm the position of the hanging hole, make sure it is horizontal, and use a marker to mark the hole positions 1234 on the wall.
• Note: Please keep the proper distance from the mirror to the faucet.
• Use an electric drill to punch holes at the marked spots, and then apply wall anchors with a hammer.
• Note: Please wear goggles and pay attention to safety.

Insert the screw

Screw the two brackets on the wall.

• Connect the power. You can use the plug directly or connect the wire to a standard switch lighting circuit.

Use plug

• After hanging the mirror, insert the plug directly into the standard socket.

Installation hardwired

• Cut the plug and connect the mirror’s wire to the power by the wire connectors.
• DANGER: Before installation, make sure the main power is cut off.
• BLACK WIRE — POWER SUPPLY L (LIVE)
• WHITE WIRE — POWER SUPPLY N (NEUTRAL)
• GREEN WIRE — POWER SUPPLY E (EARTH)
• WARNING: This mirror must be earthed.
• Place the mirror against the wall, align the hook with the bracket slot, slowly lower it so that the hook fits into the slot, and gently shake the mirror to ensure that the mirror is securely installed.
• Note: Two-person installation.
• If you have any questions, please feel free to contact us at sales@tetote-tech.com

Documents / Resources

| TETOTE B0C5XMK3ST 60x36 Bathroom LED Mirror [pdf] Instruction Manual
B0C5XMK3ST 60x36 Bathroom LED Mirror, B0C5XMK3ST, 60x36 Bathroom LED Mirror, Bathroom LED Mirror, LED Mirror
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>