Composite Prime XS Lava End Cap Instructions
- June 9, 2024
- Composite Prime
Table of Contents
Composite Prime XS Lava End Cap
Fitting Guide
It is recommended that HD Deck® XS is installed as per this fitting guide, paying special attention to steps 1 & 6 *when using more than one pack on a project please check batch numbers to ensure all product is from same batch
-
We recommend using treated 47x100mm timber joists and building in a gradual gradient of at least 1 in 100 (1%) that runs away from any adjoining buildings. Boards should run lengthways down this gradient to help water naturally disperse.
IMPORTANT: Spacing between the joists should be no greater than 300mm between each joist. -
We recommend adding HD Protect™ Premium Joist Tape to the top and exposed cut ends of the timber to protect it from moisture that can cause rot and loosening of screws.
Place the first piece of decking on the timber frame with the decking running perpendicular to the joists. The first piece of deck may be secured with starter clips. Do not screw or nail through HD Deck® XS, use one Universal Clip and screw on every joist. -
To secure the first board, use one Universal Clip and screw on every joist. Take a screw, place in the hole located in the Universal Clip and screw into the wooden joist. Do not tighten at this stage. Make sure the boards do not overhang the joist at the edge by more than 25mm and a 10mm expansion gap should be left between the wall or other fixed objects surrounding the deck.
-
Take the next piece of deck and securely push into the Universal Clips. Now nip the screw to secure the Universal Clip against the board. Do not over tighten. Now repeat steps 3 and 4 to cover the deck, using one Universal Clip and screw on every joist.
CUTTING NOTE:
When cutting, always saw the board face up with a new fine-toothed blade to
prevent dragging that can cause furring and split ends after installation. If
making a large number of cuts, the blade should be replaced regularly.
IMPORTANT: Do not allow deck boards to meet at the ends. When installing
in temperatures of:
-
15˚C or above allow a 5mm gap for expansion.
-
Between 10-15˚C allow a 6mm gap for expansion.
-
Between 5-10˚C allow a 7mm gap for expansion.
-
Do not install in temperatures below 5˚C. Joins should only occur over double joists with a clip securing each end.
-
To fit the final boards, first measure the width of the final two boards to find out where the outer edge of the final board will lie. Using these marks, fit starter clips and slot the final board into place. Now insert the penultimate board, slide down the required number of Universal Clips and screw these into place.
-
If using end caps, apply a high quality grab adhesive to the end caps to secure for extra adhesion. Wipe away any excess from the edge of the cap.
-
If using fascia, drill pilot holes with counterbore through the fascia at 200-300mm intervals. According to ambient temperature allow a 5-7mm gap between end of deck board and the fascia. Screw fascia to the joist. Always screw fascia to the joist at a 90° degree angle.
Composite Prime Care & Maintenance Guidelines
Care Guidelines
HD Deck® XS is a low maintenance product but periodic cleaning is recommended.
Your HD Deck may appear clean, however, it is important to prevent the build-
up of pollen and debris that can cause mold growth. It is recommended that
furniture placed on HD Deck® XS is fitted with rubber or felt feet to prevent
unnecessary scrapes.
Weathering
During the first 6-12 months the colour pigments will stabilize, during this
time fading may occur before weathering naturally.
Cleaning Guidelines
Domestic pressure washers may be used with caution, in conjunction with the
spray nozzle, to remove stains, ground-in dirt and chalk. Keep a minimum
distance of 1ft between the nozzle and the deck to prevent damage to the deck.
It is always recommended that you test a small area in an inconspicuous place
to determine if the cleaning product being used to clean/remove stains from
your deck will cause any unwanted discolouration.
Dirt, debris and watermarks
Clean the decking to remove dirt or debris by using soap, hot water and a
stiff bristle. Rinse thoroughly.
Mold and Mildew
Use an organic patio cleaner such as Algon or a light bleach solution. Ensure
all detergent is washed off after use.
Berries and Wine Stains
Mix an eco-friendly bleach in hot water. Scrub the stain lightly and
immediately rinse the area thoroughly. Note: Using too much bleach may cause
lightening of the deck colour. The stain may not disappear entirely.
Rust Stains, Ground-in Dirt and Grime
Use a cleaning product containing oxalic or phosphoric acid base to lighten or
remove the rust or dirt. Product may need to sit on stain 10-15 minutes. Rinse
thoroughly.
Oil and Grease Stains
Scrub in a household-degreasing agent as soon as the stain occurs. Rinse
thoroughly with warm water. Or use Abzorbit grease and oil stain remover.
Chalk Markings
Scrubbing the area with hot soapy water may dislodge some of the chalk. Rinse
thoroughly.
Ice and Snow
Rock salt, available in many home centres, will melt ice on decking. Rinse
thoroughly when practical.
Images and drawings are for illustrative purposes only. HD Deck® XS may be
laid in a variety of patterns, we recommend that you draw out how you would
like your deck to appear, making notes of joins and joists before starting the
installation. For elevated decks greater than 600mm (0.6m) in height we
recommend using a professional installer. When cutting, always saw the board
face up with a new fine-toothed blade to prevent dragging that can cause
furring and split ends after installation. If making a large number of cuts,
the blade should be replaced regularly. Don’t forget to register your
warranty,
within 45 days of purchase, at www.composite-prime.com/register-
warranty.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>