BEGA 24351 Wall Luminaire Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 24351 Wall Luminaire Instruction Manual
Dimension
Application
Wall luminaire with asymmetrical light distribution.
For lighting ceiling, wall and ground surfaces.
The asymmetrical light distribution is particularly suitable for the spatial
illumination of surfaces.
Product description
Luminaire made of aluminium alloy,
aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Clear safety glass
Reflector made of pure anodised aluminium
Swivel range around the horizontal axis
+90 ° to -30 ° in increments of 10°
Mounting plate with 3 fixing holes ø 5.5mm
Angle 120° · Pitch circle ø 85mm
2 cable entries for through-wiring of mains
supply cable ø 7-10.5mm, max. 5G1.5@
Connecting terminal 2.5@
with plug connection
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-275 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains
and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect
temperature-sensitive components without
switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK10
Protection against mechanical impacts < 20 joule
– Safety mark
– Conformity mark
Weight: 5.0 kg
This product contains light sources of energy efficiency class(es) C
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
Module connected wattage 21.3 W
Luminaire connected wattage 24.5 W
Rated temperature ta=25 °C
Ambient temperature ta max=50 °C
24 351K3
Module designation LED-0971/830
Colour temperature 3000 K
Colour rendering index CRI >80
Module luminous flux 4135 lm
Luminaire luminous flux 3256 lm
Luminaire luminous efficiency 132,9 lm/W
24 351K4
Module designation LED-0971/840
Colour temperature 4000 K
Colour rendering index CRI >80
Module luminous flux 4255 lm
Luminaire luminous flux 3350 lm
Luminaire luminous efficiency 136,7 lm/W
Installation
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping
Undo the hexagon socket screws (wrench size 3mm) as far as they will go.
Rotate and remove the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Note position of application of the mounting plate “arrow down”.
Fix the mounting plate with enclosed or any other suitable fixing material
onto the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.
The two connecting terminals marked DA, DA are provided for digital control
purposes.
If these terminals are not assigned, the luminaire will work with full light
output.
Push plug into coupler as far as it will go.
Place the luminaire onto the mounting plate, adjust and fix it.
Adjustment of beam direction:
Loosen acorn nut M 10.
Make luminaire adjustment.
Tighten the acorn nut.
Torque: 24 Nm.
Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
LED power supply unit DEV-0402/700i
LED module 3000 K LED-0971/830
LED module 4000 K LED-0971/840
Reflector 76 001 373
Gasket glass frame 83 000 924
Gasket mounting box 83 001 838
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>