BEGA 24 604 Light Brick LED Instruction Manual

Table of Contents

Product Name: Lichtbausteinb Rectangle
Application: Ceiling and wall luminaire for many lighting tasks
Ideal for places where a soft and uniform lighting distribution is required
For interior and exterior applications
Module Designation: 24 604 K3
Color Temperature: 3000 K
Colour Rendering Index (CRI): Ra > 80
Module Luminous Flux: 1520 lm
Luminaire Luminous Flux: 1106 lm
Luminaire Luminous Efficiency: 74.7 lm / W
Product Description: Luminaire made of aluminum alloy,
aluminum, and stainless steel
Distance Apart: 184 mm
Safety Class: I
Protection Class: IP 44
Weight: 1.8 kg

Ensure compliance with national safety regulations during installation and operation.
The installation and commissioning should only be carried out by a qualified electrician.
Avoid improper use or installation that may cause damage. The manufacturer does not accept liability for such damage.
If modifications are made to the luminaire, the person responsible for these modifications is considered the manufacturer.
The electronic components in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
For additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website at www.bega.com.
Avoid using high-pressure cleaners for cleaning the luminaire.
To replace the LED module, follow the mounting instructions provided by BEGA.
Close the luminaire after replacing the LED module.
Spares available: Spare glass LED-1250/830, LED module 3000 K (part number: 11 002 158 .0)

Application

Lamp

4 604K3

Luminaire made of aluminum alloy, aluminum and stainless steel
BEGA Unidure® coating technology
Opal glass satin matt 2 mounting holes ø 6.5mm
Distance apart 184mm 1 cable entry for mains supply cable up to ø 10,5mm
Connection terminal 2.5@
Earth conductor connection
LED-Module for mains voltage 220-230 V y 50/60 Hz
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 44
Protected against granular foreign bodies ≥ 1 mm and splash water Impact strength IK05
Protection against mechanical impacts < 0.7 joule
r – Safety mark
c – Conformity mark
Weight: 1.8 kg
This product contains light sources of energy efficiency class(es) F

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Undo screws (key slots) and remove the LED unit.
Lead the main supply cable through the cable entry into the luminaire back housing.
Fix the luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied.
Make an earth conductor connection.
Push silicone sleeves over the lines and make the electrical connection.
Assemble LED-unit.
Snap the opal glass into the lower spring clips, centralize, and push into the upper spring clips.

Cleaning · Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified electrician or a comparably qualified person using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced.
Close the luminaire.

Spares