Jiangsu Jinshi Legend Technology ZMLE10N Projector User Guide

Jiangsu Jinshi Legend Technology ZMLE10N Projector

SAFETY INSTRUCTIONS

Before use. please read the product instructions carefully and keep them properly for use in case of urgent need. During product projection, it is forbidden to block the air inlet or outlet of the product to avoid damage caUsed by excessive machine temperature Products are not allowed to fal or strike from high altitude to avoid damage to the machine: To avoid eye injury. do not look directly into the machine lens. there is any problem with the product, do not disassemble it without permission. Please contact the professional after-sales assistance department.

warning

Do not disassemble. bump. squeeze or throw into fire. If there is serious swelling. do not continue to use.Do not Use the battery after it is soaked in water Do not expose to high temperature.

THE ANNOUNCEMENT

The company has always been in the spirit of excellence. always committed to improve, improve product performance. to provide users with high quality. competitive prices of products. Al pictures and function descriptions in this manual are subject to the material object and factory default. The Company reserves the right to improve the product functions and man-machine interface described in this manual without prior notice. The final material object shll prevail. Please be sure to take good care of your machine. the company will not be responsible for any loss caused by soft ware. hardware misoperation or maintenance. or any loss caused by disclosure of personal information to a third party. The company will not be responsible for any unexpected losses that may occur during the use of the manual or any third party claims arising from the use of the
product.

ITEM LISTING

Remarks: Thank yoU for buying our products. Please check whether the product received is consistent with the list; if the products and accessories you receive do not match the list, please contact customer service immediately.

HOME PAGE

1. The home page contains six functions: Eshare, Miracast, HDMI. Settings. media Center, and broWser. When selected, press OK to enter
2. Computers, set-top boxes. game consoles and other equipment as signal output end, home projector as signal input end, the output end needs to have HDMl interface.
3. Connect the output and input through the HDMIl cable, and select the HDMI icon of the projector.as shown in Figure 2

SETTINGS

Select the ‘Settings” on the home page and press ‘Ok to enter. You can set the network. Bluetooth. projection mode. sound. system and other functions.as shown in Figure 3 and figure 4 below

NETWORK

1. The first item in the Settings menu is “Network’.as shown in Figure 5
2. Click “Network Switch’ to enable /disable the network function.
3. In the list below. find the required hotspot and click, then enter the correct password. You can connect the projector to the hotspot (WF) to play online video.etc.
4. In the Connected hotspot bar. press Ok to enter the Manual Settings interface. where you can modify IP Address and Gateway. You are not advised to change thepassword.as shown in Figure 6:

BLUETOOTH

1. The second item in the “Settings’ menu is “Bluetooth’.as shownin Figure 7. This Bluetooth is different from the Bluetooth in Bluetooth audio. This Bluetooth takes the projector as the host (sender). and connects to the external Bluetooth audio,Bluetooth headset, and Bluetooth keyboard and mouse. Operation method is similar to android phone connected to bluetooth headset.
2. Cick ‘Bluetooth Switch to enable/disable bluetooth function.
3. Click ‘Device Name (default: Home Projector)
4. ln the Paired Devices list. yoU can view the paired Bluetooth devices. In a Bluetooth device bar. press Ok to connect/unpair the Bluetooth device.
5. In the ‘Available Devices” list. you can view the Bluetooth device to be connected.and click the specific Bluetooth device to pair.

PROJECTION SETTINGS

1. The four modes in “projection mode’ can be adjusted to meet needs in different scenarios as shown in Figure 9:
2. “Automatic up and down trapezoid can automatically perform trapezoid correction.as shown in Figure 10
3. “Manual up and down trapezoid’ can be manually changed parameters for trapezoid correction.as shown in Figure l1
4. “Picture zoom’ can change the picture size in equal proportion,as shown in Figure 12:) “Four Angle Correction can adjust the angles of the four angles to meet the requirements of side casting and other scenes.as shown in Figure 12. Press ‘OK” to switch vertices. Press “Up Down, Left, Right” to adjust the the whole picture. Press the Menu to restore data.
   Tips: It is recommended that the side casting angle should not exceed 15 degrees

SOUND **

**

1. The fourth item in the “Settings’ menu is ‘Sound”. as shown in figurel3:
2. “button sound’ in ‘Sound Switch can turn on/off the sound effect when pressing the button.as shown in Figure 14:

SYSTEM SETTINGS

1. The fifth item in the “Settings menu is “System Settings’. as shown in Figure. 15
2. The language type of the system can be switched

ABOUT

1. The sixth item in the “Settings menu is “System Settings, as shown in Figure 17:
2. About the model. system version. “WIFI MAC and other information of the projector that can be viewed in:
   A) “Model: model of the projector.
   B) “System Version’ : the current software system version number of the projector.
   C) WIFI MAC” : the MAC address of the WIFI carried by the projector.

MEDIA CENTER
Select the “Media Center on the home page and press ‘Ok” to enter to check videos, music.pictures, etc.. as shown in FIG. 19 and 20 beloW

BROWSER

Select the “Browser on the home page and press “Ok” to enter and search the content, as shown in Figure 21 below:

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment
NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to corect the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• environment. This equipment should be installed and operated with minimum distance
  20cm between the radiator and your body.Consult the dealer or an experienced radio/TV technician for help. The equipment complies with FCC Radiation exposure limit set forth for uncontrolled

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>