BEGA 24 728 Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
IP 65
Technical amendments reserved
Wall luminaire
24 728 Wall Luminaire
Instructions for use
Application
Wall luminaire with single-sided light output for illumination and design
tasks in architecture.
The luminaire can be installed with the light distribution opening upwards or
downwards.
Product description
Luminaire made of aluminium alloy,aluminium and stainless steel
BEGA Unidure® coating technology Colour graphite, silver or white
Matt safety glass
Reflector surface made of pure aluminium
Mounting plate with 4 elongated holes, width 4.4 mm, distance 62 x 95 mm
2 cable entries for through-wiring of mains supply cable ø 7-12 mm
Connecting terminal 2.5@ with plug connection
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 170-276 V
BEGA Thermal Switch ®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK05
Protection against mechanical
impacts < 0.7 joule
– Safety mark
– Conformity mark
Weight: 2.2 kg
This product contains light sources of energy efficiency class(es) C, D
Light technique
Broad spread light distribution.
Half beam angle 72°
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Lamp
| Module connected wattage | 8.4 W |
|---|---|
| Luminaire connected wattage | 10 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 50 °C |
24 728 K3
| Module designation | LED-1145/830 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 1480 lm |
| Luminaire luminous flux | 1045 lm |
| Luminaire luminous efficiency | 104,5 lm / W |
24 728 K4
| Module designation | LED-1145/840 |
|---|---|
| Colour temperature | 4000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 1555 lm |
| Luminaire luminous flux | 1098 lm |
| Luminaire luminous efficiency | 109,8 lm / W |
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Undo hexagon socket head screws (wrench size 3 mm) up to the stop and
disassemble the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Fix the mounting plate with enclosed two fixing screws diagonally on the
mounting surface.
Make earth conductor connection and electrical connection to the connecting
terminal (plug connection).
Push plug into coupler as far as it will go.
Place luminaire housing onto the mounting plate and fix it.
Make sure that gasket is positioned correctly.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
| LED power supply unit | DEV-0341/250 |
|---|---|
| LED module 3000 K | LED-1145/830 |
| LED module 4000 K | LED-1145/840 |
| Reflector | 76 001 976 |
| Gasket | 83 002 074 |
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>