BEGA 50066.2 LED Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50066.2 LED Wall Luminaire
Product Information
Product Description| Metal housing, finish Stainless steel Hand-blown opal
glass,
satin matt
---|---
Weight| 1.0 kg
Energy Efficiency Class| F
Overvoltage Protection| The electronic components installed in the luminaire
are
protected against overvoltage in accordance with DIN EN 61547. For
additional protection against transients, etc. separate overvoltage
protection components are recommended.
Module Information| | Module Designation| Colour Temperature| Colour Rendering
Index| Module Luminous Flux| Luminaire Luminous Flux| Luminaire Luminous
Efficiency
---|---|---|---|---|---
LED-0607/930| 3000 K| Ra > 90| 940 lm| 860 lm| 86 lm/W
Product Usage Instructions
Safety:
- The installation and operation of this luminaire are subject to national safety regulations.
- Installation and commissioning may only be carried out by a qualified electrician.
- The manufacturer accepts no liability for damage caused by improper use or installation.
- If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Installation:
-
Loosen knurled nuts and replace glass from luminaire
housing. -
Pull silicone sleeves over the wires, make earth connection and
electrical connection to the terminals. -
Fix luminaire housing with enclosed or any other suitable
fixing material onto the mounting surface. -
Place glass with its opening over the LED module and fix it
hand tight onto the luminaire housing by means of the knurled
nuts.
LED Module Replacement:
- The designation of the LED module can be found on a label inthe luminaire.
- Switch off power to the luminaire and make sure it is voltage-free.
- Refer to the installation manual of the LED module for replacement instructions.
Dimension
Wall luminaire for indoor use
Application
Free-radiating wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt and metal housing, for all lighting tasks.
Product description
- Metal housing, finish Stainless steel
- Hand-blown opal glass, satin matt
- 2 mounting holes ø 5 mm
- Distance apart 115 x 55 mm
- Connecting terminals 2.5@
- Earth conductor connection
- Installation surface 145 x 86 mm
- LED-Module for mains voltage
- 220-230 V y 50/60 Hz
- BEGA Thermal Switch®
- Temporary thermal shutdown to protect temperature-sensitive components
- Safety class I
- – Safety mark
- – Conformity mark
- Weight: 1.0 kg
- This product contains light sources of energy efficiency class(es) F
Safety
- The installation and operation of this luminaire are subject to national safety regulations.
- Installation and commissioning may only be carried out by a qualified electrician.
- The manufacturer accepts no liability for damage caused by improper use or installation.
- If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
- The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
- To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
- You can find them on our website at www.bega.com.
Lamp
- Luminaire connected wattage 10 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 40 °C
- 50 066.2 K3
- Module designation LED-0607/930
- Colour temperature 3000 K
- Colour rendering index Ra > 90
- Module luminous flux 940 lm
- Luminaire luminous flux 860 lm
- Luminaire luminous efficiency 86 lm / W
Installation
- LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
- Loosen knurled nuts and replace glass from luminaire housing.
- Pull silicone sleeves over the wires, make earth connection and electrical connection to the terminals.
- Fix luminaire housing with enclosed or any other suitable fixing material onto the mounting surface.
- Place glass with its opening over the LED module and fix it hand tight onto the luminaire housing by means of the knurled nuts.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
- The designation of the LED module is noted on a label in the luminaire.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified electrician or a comparably qualified person using standard tools.
- Disconnect the system and open the luminaire.
- Please follow the installation instructions for the LED module.
- Defective glass must be replaced.
- Close the luminaire.
Spares
- Spare glass 11 003 189 .0R G
- LED module 3000 K LED-0607/930
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com