BEGA 51 014.2 Ceiling Luminaire Instruction Manual

June 12, 2024
BEGA

BEGA 51 014.2 Ceiling Luminaire

BEGA-51-014.2-Ceiling-Luminaire-product

Product Information

  • Product model: 51 014.2
  • Lamp Module connected wattage: 42.6 W
  • Luminaire connected wattage: 47.4 W
  • Rated temperature: ta = 25°C
  • Ambient temperature: ta = 40°C
  • Color temperature: 3000K
  • Color rendering index (CRI): > 90
  • Module luminous flux: 6435 lm
  • Luminaire luminous flux: 3918 lm
  • Luminaire luminous efficiency: 82.7 lm/W

Product Usage Instructions

  1. During installation or relamping, avoid touching the light output opening of the LED directly.
  2. To remove the synthetic cover, turn it anti-clockwise while simultaneously pushing it up against the luminaire fitting.
  3. The installation and operation of this luminaire should be carried out by a qualified electrician in accordance with national safety regulations.
  4. The manufacturer does not accept liability for damage caused by improper use or installation.
  5. If modifications are made to the luminaire, the person responsible for these modifications will be considered by the manufacturer.
  6. The electronic components in the luminaire are protected against overvoltage according to DIN EN 61547. Additional overvoltage protection components are recommended for extra protection.
  7. Spare parts available include a synthetic cover, LED power supply unit, shield, and LED unit with a color temperature of 3000 K. The part numbers are as follows:
    • Synthetic cover: 15 000 634 DEV-0338/1050i
    • LED power supply unit: 71 001 761 L12
    • Shield: 75 005 486 K3
    • LED unit: 75 005 486 K3

Application

Ceiling luminaire · indoor luminaire impact-resistant synthetic diffuser and metal housing for non-glare light deflected downwards.

Product Description

  • Ceiling luminaire »STUDIO LINE«
  • Luminaire housing made of aluminum, surface Colour velvet black inside hue aluminum matt
  • Metal luminaire mounting plate, finish Colour velvet black
  • Impact-resistant synthetic diffuser, white, with bayonet closure 2 mounting holes ø 6 mm
  • Distance apart 340 mm 2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x 1.5@
  • Connection terminal 2.5@
  • Earth conductor connection
  • LED power supply unit 220-240 V x 0/50-60 Hz
  • DC 176-280 V
  • During DC operation the LED power is reduced to 15 %
  • DALI-controllable
  • Number of DALI addresses: 1
  • Basic insulation is provided between the mains and control cables BEGA Thermal Control®
  • Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
  • Safety class I
  • Impact strength IK10
  • Protection against mechanical impacts < 20 joule
    • Safety mark
    • Conformity mark
  • Weight: 3.0 kg
  • This product contains light sources of energy efficiency class(es) D

Lamp Specification

  • Module connected wattage 42.6 W
  • Luminaire connected wattage 47.4 W
  • Rated temperature ta = 25 °C
  • Ambient temperature ta max = 40 °C

51 014.2 K3

  • Colour temperature 3000 K
  • Colour rendering index CRI > 90
  • Module luminous flux 6435 lm
  • Luminaire luminous flux 3918 lm
  • Luminaire luminous efficiency 82,7 lm / W

Installation

LED are high-quality electronic components!

  • Please avoid touching the light output opening of the LED directly during installation or relamping.BEGA-51-014.2-Ceiling-Luminaire-fig-2

Before installing onto the ceiling the luminaire mounting plate must be inserted into the luminaire housing.

  • Thereby pass the mains supply cable through the grommet into the luminaire mounting plate.
  • Fix mounting plate inside the luminaire housing with enclosed or any other suitable fixing material onto the mounting surface.
  • Dismantle the mains supply cable approx. 60 mm.
  • Make earth and electrical connections to the terminals.
  • For digital control please use the connecting terminal DA, DA.
  • In case this terminal is not used the luminaire will be operated at full light output.
  • In order to securely install the synthetic cover in the fitting, the top opening of the synthetic cover must be inserted into the luminaire housing at an angle.
  • Make sure that at least one of the recesses in the edge of the synthetic cover matches the position of one of the lugs on the fitting – see drawing.

Dimension

BEGA-51-014.2-Ceiling-Luminaire-fig-1

IMPORTANT:
Turn the synthetic cover upwards into the fitting as far as it will go. Now secure the synthetic cover in the fitting by turning it clockwise.

  • Only then is the synthetic cover held securely in place and resistant to vibration.
  • The synthetic cover is removed by turning it anti-clockwise as far as it will go while simultaneously pushing the synthetic cover up against the luminaire fitting.

Safety

  • The installation and operation of this luminaire are subject to national safety regulations.
  • Installation and commissioning may only be carried out by a qualified electrician.
  • The manufacturer accepts no liability for damage caused by improper use or installation.
  • If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

  • The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
  • To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
  • You can find them on our website at www.bega.com.

Cleaning And Maintenance

  • Clean the luminaire regularly with solvent-free cleansers from dirt.

Replacement of the LED unit

  • The designation of the LED unit is noted on a label in the luminaire.
  • The light color and light output of BEGA replacement units correspond to those of the
  • LED units were originally fitted. The LED unit can be replaced by qualified persons using standard tools.
  • Disconnect from the main supply. Unscrew the synthetic diffuser from the luminaire
  • housing by turning it counterclockwise.
  • Disassemble the LED unit.
  • Assemble the LED replacement unit.
  • Note the installation instructions of the LED unit.
  • Screw in the synthetic diffuser by turning it clockwise.
  • A damaged synthetic diffuser must be replaced.

Spares

  • Synthetic cover 15 000 634
  • LED power supply unit DEV-0338/1050i
  • Shield 71 001 761 L12
  • LED unit 3000 K 75 005 486 K3

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com.

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals