AVSS M350 RTK Drone Parachute Recovery System Instruction Manual
- June 1, 2024
- AVSS
Table of Contents
- M350 RTK Drone Parachute Recovery System
- Specifications
- Product Usage Instructions
- 1. Safety Precautions
- 2. Deployment Guidelines
- 3. Position Mode Usage
- 4. Manual Triggering
- 5. Firmware Updates
- Q: Can the PRS-M350 be used with other drone models?
- Q: What should I do if I encounter a critical failure during
- Q: How often should I perform maintenance on the PRS-M350?
M350 RTK Drone Parachute Recovery System
“`html
Specifications
-
Product: PRS-M350 for DJI M350 RTK
-
Version: 1.2
-
Parachute Packing Interval: Extended from 12 months to 18
months -
Minimum Deployable Altitude: Defined in the manual
-
Position Mode: N-mode recommended
-
IP Rating: Ingress Protection Rating
Product Usage Instructions
1. Safety Precautions
Always ensure proper eye protection when handling the PRS-M350
to prevent potential injury.
2. Deployment Guidelines
Follow the guidelines provided in the user manual for parachute
deployment altitude and conditions.
3. Position Mode Usage
Utilize the N-mode for optimal performance, especially when GPS
signal is strong. Refer to DJI.com for complete details on Position
Mode.
4. Manual Triggering
Use the manual triggering device only when necessary, as
described in the manual, to initiate parachute deployment.
5. Firmware Updates
Refer to Appendix C.3 for the procedure on updating firmware,
especially for compatibility with PRS-M300.
FAQ (Frequently Asked Questions)
Q: Can the PRS-M350 be used with other drone models?
A: The PRS-M350 is specifically designed for use with DJI M350
RTK and may not be compatible with other models.
Q: What should I do if I encounter a critical failure during
flight?
A: The Autonomous Triggering System (ATS) will detect and
initiate parachute deployment in case of critical failure. Follow
the procedures outlined in the manual for such situations.
Q: How often should I perform maintenance on the PRS-M350?
A: Regular maintenance and checks are recommended as per the
guidelines provided in the user manual. The extended parachute
packing interval is now 18 months.
“`
PRS-M350 for DJI M350 RTK
Version 1.2
© 2023 AVSS ALL RIGHTS RESERVED
1
PRS-M350(EX) USER MANUAL FOR DJI M350 RTK
Using this Manual
1. Revision Notes
Revision #
Date
Revision Description
1.0
October 4, 2023 – Initial Internal Release
1.1
October 19, 2023
– Added Firmware Update Procedure in Appendix C.3 for PRS-M300 Compatibility
1.2
December 16, 2023
–
Extended the parachute packing interval from 12 months to 18 months
2. Legends
Warning
Important
Tips
FOR THE MOST RECENT VERSION OF THE USER MANUAL, PLEASE GO TO: https://www.avss.co/products/prs-for-dji-M350-rtk/
© 2023 AVSS ALL RIGHTS RESERVED
2
PRS-M350(EX) USER MANUAL FOR DJI M350 RTK
Using this Manual
2 1. Revision Notes
____ 2 2. Legends
__ 2
Disclaimer ____
5 Terms, Acronyms, & Abbreviations
6 Safety Instructions
____ 7 Limitations
__ 8 1.
Operational & Environmental Conditions
____ 8 PRS-M350
Overview 9 1. First
Time Setup____ 9
2. General Use
____ 9
Features, Specifications, Testing, & Compatibility
9 1. Features
____ 10 2.
Specifications
____ 11 3.
Payloads ____
12 Warranty____
13 What’s in the Box:
___ 14 1. Parts
Included ____ 14
System Overview ____
15 1. Parachute Recovery System
_ 15 2. Attachment Bracket
___ 16 3. Flight
Termination System Through PSDK _ 17
4. Manual Triggering Device
_ 18 Installation
___ 19 1.
Electronic Module
19 2. Parachute
PodTM ____ 20 3.
Attachment Bracket
21 4. PSDK Flight Termination System Firmware Configuration
__ 26 Battery & Charging
34 1. Battery
Safety ____ 34 2.
Battery Charging
__ 34 3. Changing
Electronic Module Battery __ 35
Firmware & SD Card __
36 1. MicroSD Card
____ 36 2.
Firmware Updates__
37
© 2023 AVSS ALL RIGHTS RESERVED
3
PRS-M350(EX) USER MANUAL FOR DJI M350 RTK
Status Indications
____ 39 1. PRS-M350
Indications __ 39 2.
Manual Triggering Device Status Indication
39 3. Manual Triggering Device
Synchronization 40 Operating
Procedures ____ 41 1.
Hangar Checklist
__ 41 2.
Installation Checklist
_ 41 3. Pre-Flight
Checklist ____ 41 4.
In-Flight Checklist
___ 42 5. Landing
Checklist__ 42 6.
Post-Flight Checklist (No Deployment)
42 7. Deployment Checklist
____ 42 8. Post-Flight
Checklist (With Deployment) 42
Maintenance & Care
43 1. Post-Flight (Monthly)
__ 43 2.
Transportation __
43 3. Storage
____ 43 4.
Extended Storage Considerations
43 Frequently Asked
Questions 44 Parachute
PodTM Deployment Procedures ____ 45
Customer Support ____
46 Appendix A: DJI M350 RTK & Payload References
__ 47 Appendix B: IMU Calibration
Instructions 48 Appendix C:
Additional Information ____ 54 1.
Pre-Flight FTS Check
___ 54 2. Ground Risk
Buffer Prescription __ 55 3.
Firmware Update Process for Conversion From PRS-M300 to PRS-M350
__ 56
© 2023 AVSS ALL RIGHTS RESERVED
4
PRS-M350(EX) USER MANUAL FOR DJI M350 RTK
Disclaimer
· You must read the ENTIRE user manual to become familiar with the features of
this product before operation. Failure to operate the product as instructed by
the user manual may result in damage to the product or personal property and
can cause serious injury. Failure to operate the product as instructed may
also void your warranty.
· This is product has been designed for and should only be used by qualified
professionals only.1 · This product is designed to increase the safety of both
people and property on the ground during
DJI M350 RTK operations while potentially helping DJI M350 RTK operators meet
compliance requirements. However, this product is not a replacement for safe
operating practices and should serve only as a last resort in the event of an
emergency. · Before use, you shall refer to the DJI M350 RTK manufacturers’
documentation to determine if this product complies with specific operating
requirements and warranty conditions of the DJI M350 RTK. Failure to comply
with the operating requirements of this product and/or DJI M350 RTK
manufacturer product may result in damage to the DJI M350 RTK, damage to
nearby property, harm to bystanders, and/or cause serious injury. · Always use
proper judgment when attempting to mitigate risks and/or danger in
emergencies. Do not make or attempt any alterations or adjustments to this
product or its use as it could result in serious injury, or damage to the
product or other property and it will void the warranty. · AVSS Aerial
Vehicle Safety Solutions Inc. (AVSS) assumes no liability and/or ownership of
any failure event that may occur while the system is attached to a DJI M350
RTK. The use of AVSS products is at the risk of the user. · Do not store the
PRS-M350 and/or any of the associated parts and accessories in any extreme
cold, hot or humid environments.
o Less than 3 months: -20° to +45° C o More than 3 months: +22° to +28° C ·
This document and the information contained herein are proprietary and
commercially confidential to AVSS. It is prohibited to use, disclose,
reproduce, distribute, or use this user manual other than persons for which
purchased the product.
THIS USER MANUAL MAY BE UPDATED AT ANY POINT AND WITHOUT NOTIFICATION. BEFORE
USE, READ, IN ITS ENTIRETY, THE MOST RECENT VERSION OF THIS USER MANUAL TO
UNDERSTAND ALL PROCEDURES, RISKS, AND RESTRICTIONS ASSOCIATED WITH THIS
PRODUCT BEFORE OPERATING.
1 Professional qualifications are determined by the jurisdiction/country in which the commercial DJI M350 RTK is operating.
© 2023 AVSS ALL RIGHTS RESERVED
5
PRS-M350(EX) USER MANUAL FOR DJI M350 RTK
Terms, Acronyms, & Abbreviations
Terms & Definitions
AGL
Above Ground Level.
Autonomous Triggering System that is independent of any flight critical system of
ATS
the DJI M350 RTK that will detect and initiate parachute deployment upon
detection of a critical failure of the DJI M350 RTK during flight.
Authorized Dealer An AVSS approved distribution partner who sells the PRS-M350.
Drone
When referring to a DJI M350 RTK, other relevant terms include Aircraft, RPAS, sUAS, UAS, and UAV.
End-User
The owner of the PRS-M350 who had purchased the system from an AVSS Authorized Dealer.
FTS
Flight Termination System is a device that will disable the propulsion system of the DJI M350 RTK.
IP Rating
Ingress Protection Rating.
LiPo
Lithium-Polymer (Chemistry of battery).
Manual Triggering Device
The manual triggering device, initiated by pressing the triggering button, initiates the deployment of the parachute recovery system at the discretion of the pilot in command.
Minimum Deployable Altitude
The
lowest
altitude
at
which
the
PRS-M350
is
rated
to
deploy
successfully.
Parachute PodTM
This refers to the replaceable Parachute PodTM that contains the parachute of the AVSS PRS-M350.
Position Mode
The PRS-M350 shall be used only in N-mode (Normal): N-mode works best when the GPS signal is strong. The DJI M350 RTK utilizes GPS and Forward and Downward Vision Systems to locate itself, automatically stabilize, and navigate between obstacles. Complete details can be found at www.DJI.com.
PRS
Parachute Recovery System.
“shall” versus “should” versus “may”, v–use of the word “shall” implies that a
Shall
procedure or statement is mandatory and shall be followed to comply with this specification, “should” implies recommended, and “may” implies optional at the
discretion of the supplier, manufacturer, or operator.
© 2023 AVSS ALL RIGHTS RESERVED
6
PRS-M350(EX) USER MANUAL FOR DJI M350 RTK
Safety Instructions
Eye Protection
As with any system designed to launch a mass at high velocity, precautions shall be taken to prevent potential injury.
Never point the While the PRS-M350 includes features to prevent unintentional deployments,
Parachute PodTM users shall be aware that the Parachute PodTM is launched vertically. It is
towards anyone or recommended that the operator maintains a clear area of at least 5 meters after
anything
the system has been powered.
Disarming Manual Always disarm the Manual Trigger Device before approaching the DJI M350 RTK Trigger Device after a landing or in the event of an aborted takeoff.
Ensure PRS-M350 is Do not pick up the PRS-M350 when it is armed because the
sensors may DISARMED before interpret the movements as an in-flight failure.
Wait five to ten seconds for the
moving it Autonomous Trigger System to disarm.
Error Status
The system should not be used unless it is indicated that no errors are present. The system will not arm itself nor deploy in a failure scenario unless it has initialized successfully.
Low Battery
The PRS-M350 requires enough battery power to operate. Although the PRSM350 can draw power from the DJI M350 RTK as a backup if the battery becomes low during a flight, this feature is not to be used as a substitute for charging the battery prior to flight.
Parachute PodTM Repacking
Only parachutes packed by AVSS are compliant. The Parachute PodTM shall be repacked or replaced every 18 months only by AVSS. You will no longer be compliant and will void the warranty if you attempt or repack the Parachute PodTM.
Always follow DJI’s maximum specified takeoff weight when adding payloads to
Payload Configurationthe DJI M350 RTK (See Compatibility & Payloads sub-
section for a list of
compatible payload configurations).
The Autonomous Triggering System is designed to automatically detect
abnormal flight behaviors. Flying in a controlled manner and avoiding erratic
Position Mode and Flight Mode Changes
maneuvers ensures that the between pilot commands and mid-flight as the DJI M350 RTK
PRS-M350 can more accurately distinguish loss of control. Do not change the flight mode can have a hard/abrupt braking maneuver that
can exceed the maximum “30°-degree pitch angle (N-mode, Forward Vision
System enabled: 25°)”2.
Rules and RegulationsPgoilovetsrnsmhaelnl tfoblolodwiestihnethruelier sopaenrdatrineggurleagtiioonnss. put in place by civil aviation or
The PRS-M350 utilizes Li-Po batteries. Li-Po batteries are volatile and can
cause Li-Po Battery Warningfires. The user must take the necessary precautions
when charging the PRS-
M350.
2 https://enterprise.dji.com/matrice-350-rtk/specs
© 2023 AVSS ALL RIGHTS RESERVED
7
PRS-M350(EX) USER MANUAL FOR DJI M350 RTK
Limitations
1. Operational & Environmental Conditions
– DJI M350 RTK Flight Mode = N Mode – DJI M350 RTK Maximum Tilt Angle = 30°
Degrees – Maximum Take Off Weight = 9.20 kg (20.28 lbs) – Minimum Deployable
Altitude at 7.70 kg = 44.6 m (146.33 ft) – Minimum Deployable Altitude at 9.20
kg = 50.8 m (166.67 ft) – Autonomous Triggering System Arming Height = 43 m
(141.08 ft) – Manual Triggering Device Range = <2 km (<1.24 mi) – Temperature
Range = -20°C to +45°C (-4°F to 113°F) – Maximum Wind Limit for EASA M2
Mitigation = 9.35 m/s (18.1 knots) – Maximum Wind Resistance = 12 m/s (39.3
fps)
ONLY FLY THE PRS-M350 IN NORMAL (N) MODE.
DO NOT CHANGE / SWITCH FLIGHT MODES FROM NORMAL MODE TO AUTOMATED FLIGHT MODES
OR AUTOMATED FLIGHT MODES TO NORMAL MODE MID FLIGHT AS THE DJI M350 RTK MAY
MAKE AN ABRUPT STOP OR MANEUVER AND EXCEED THE “30°-DEGREE PITCH ANGLE
(N-MODE, FORWARD VISION SYSTEM ENABLED: 25°)”.
IF YOU UPDATE THE FIRMWARE ON THE DJI M350 RTK, ALL EXISTING PRSM350 PSDK
SETTINGS WILL BE REMOVED. THEREFORE, AFTER COMPLETING A FIRMWARE UPDATE, YOU
MUST PERFORM THE FIRST TIME & AFTER FIRMWARE UPDATES PROCEDURES (SEE “FIRST
TIME USE & AFTER FIRMWARE CONFIGURATION” SECTION)
IF THE PARACHUTE IS DEPLOYED IN HIGH WINDS, THE PARACHUTE CAN DRIFT. THE PILOT
MUST CONSIDER DRIFT ZONES AND THE CONSEQUENCES IN THEIR RISK ASSESSMENT.
LEAVING THE PRS-M350 ON FOR A PROLONGED PERIOD BEFORE TAKING OFF CAN CAUSE IT
TO ARM IF ENVIRONMENTAL CONDITIONS ARE CHANGING (E.G., BAROMETER DRIFT).
IF THE PRS-M350 IS INVOLVED IN A MAJOR CRASH, DO NOT REUSE THE PRSM350 WITHOUT
CONTACTING AVSS’S CUSTOMER SUPPORT AND SPEAKING WITH A REPRESENTATIVE BEFORE
THE NEXT FLIGHT.
© 2023 AVSS ALL RIGHTS RESERVED
8
PRS-M350(EX) USER MANUAL FOR DJI M350 RTK
PRS-M350 Overview
The PRS-M350 is composed of five (5) main components: 1. The Electronics
Module, which houses the battery, sensors, radio, and controller. These
electronics
also control the autonomous triggering system that will deploy the parachute.
2. The swappable Parachute PodTM, which contains a compressed spring and a
folded parachute. 3. The Flight Termination System Module, a cable adapter and
module that enables the Electronics
Module to communicate with the DJI M350 RTK’s PSDK for motor shutoff. 4. The
Bracket, which attaches the PRS-M350 to the DJI M350 RTK and allows for easy
removal. 5. The Manual Triggering Device, which allows the user to manually
initiate a parachute deployment
when desired by pressing on the red triggering button.
1. First Time Setup
When the user receives the product, the Electronics module comes mounted to
the top plate of the bracket with a Parachute PodTM already attached. For a
first-time installation, the user must remove the landing gear brackets on the
DJI M350 RTK, place an aluminum spacer block in between and remount the
landing gear bracket with the longer bolts that are provided by AVSS. This
spacer block can stay permanently attached to the aircraft and ensures that
the DJI M350 RTK can still fit in the official DJI M350 RTK supplied hard
case. The user must then enable the PSDK on the DJI M350 RTK to allow the FTS
to work, which is done using DJI Assistant software.
2. General Use
To use the PRS-M350 for a flight, the DJI M350 RTK can be unpacked from its
case and set up according to DJI’s user manual. Once the aircraft is in its
flight configuration, the AVSS bracket can be mounted to the DJI M350 RTK. The
bracket side plates connect and lock into the spacer blocks. The bracket top
plate which already has the electronics module and Parachute PodTM attached
can then be mounted and locked in place using a combination of a sliding
motion and quarter turn fasteners. The provided FTS Module can then be plugged
into the PSDK port on the DJI M350 RTK and connects to the electronics module
using the provided cable that features locking connectors. The PRS-M350 is now
fully installed. The PRS-M350 will turn on automatically when the DJI M350 RTK
is turned on. The manual triggering device is turned on by the user to ensure
that it is communicating with the PRS-M350. The manual triggering device has a
secondary arm button that must be held down for two (2) seconds to arm the
manual triggering device before the parachute can be manually deployed. Any
error with the PRS-M350 will be communicated to the user via the manual
triggering device in the form of verbal warnings and a status LED. During the
flight, the PRS-M350 Autonomous Triggering System will arm itself only once it
has reached the minimum deployable barometric altitude. Afterward, if the DJI
M350 RTK experiences a failure, using a combination of accelerometer, gyro,
and barometer data, the Autonomous Triggering System detects the failure,
forces the motors to shutoff, and deploys the parachute without the need for
pilot input. If the DJI M350 RTK experiences a flyaway, loss of communication,
or other undesirable behavior, the pilot can manually trigger the parachute
deployment to safely recover the aircraft.
Features, Specifications, Testing, & Compatibility
The PRS-M350 has been designed to easily integrate with DJI Matrice 350 RTK
(DJI M350 RTK). The attachment bracket secures the PRS-M350 without
interfering with onboard sensors and can be easily removed for transport. The
system includes an electronic module to power the Parachute PodTM and flight
termination system. The flight termination system is initiated when either the
pilot instigates a
© 2023 AVSS ALL RIGHTS RESERVED
9
PRS-M350(EX) USER MANUAL FOR DJI M350 RTK
deployment through the manual triggering device or when the Autonomous
triggering system, using the onboard sensors located in the electronic module,
determine that the DJI M350 RTK has breached the safe flying parameters. Once
the flight termination system is initiated and stops the motors from spinning,
the Parachute PodTM is deployed and will result in the DJI M350 RTK descending
under a fully inflated parachute.
1. Features
Attachment Bracket
The custom mounting bracket allows the PRS-M350 to be easily installed with minimal effort.
Independent Power Source
The PRS-M350 is equipped with an independent power source that allows the system to deploy if the DJI M350 RTK loses power.
Spring-Based Ejection
A high-energy spring is used to eject the parachute. This non-pyrotechnic system is safe for travel on commercial airlines.
Autonomous Trigger System
The Autonomous Triggering System (ATS) automatically detects failures and triggers the parachute release.
Manual Triggering The manual triggering device can initiate deployment of the parachute
Device
recovery system at the discretion of the remote pilot in command.
Flight Termination System
Plug-and-play system that cuts power to the motors in the event of a failure and to ensure that the parachute does not become entangled in the DJI M350 RTK’s propellers.
Audible Buzzer
An audible buzzer on the DJI M350 RTK will attempt to notify bystanders that the PRS-M350 has deployed and the DJI M350 RTK is descending.
Low Descent Rate
The parachute is designed to greatly reduce the descent velocity of the DJI M350 RTK in the event of a failure.
Flight Data Logging
Flight data logging to a dedicated microSD Card that is integrated in the PRSM350.
Parachute PodsTM Easily replaceable Parachute PodTM.
© 2023 AVSS ALL RIGHTS RESERVED
10
PRS-M350(EX) USER MANUAL FOR DJI M350 RTK
2. Specifications
OVERVIEW3 Total Weight Average Descent Rate (7.70 kg) Average Descent Rate
(9.20 kg) Average Impact Energy (7.70 kg) Average Impact Energy (9.20 kg)
Minimum Deployable Altitude (7.70 kg) Minimum Deployable Altitude (9.20 kg)
Parachute Reuse Method Deployment Technology Deployment Trigger PARACHUTE
RECOVERY SYSTEM Main System Weight Deployment Release Time Time to Inflation
Battery Life Operating Temperature PARACHUTE PODTM Parachute Size
Risers/Attachment Location FLIGHT TERMINATION SYSTEM FTS Method Integration
Process ATTACHMENT BRACKET Attachment Bracket Weight Material Attachment
Location MANUAL TRIGGERING DEVICE (REMOTE) Range Frequency
922 grams (2.03 lbs) 3.24 m/s (10.62 fps) 3.54 m/s (11.61 fps) 40.30 Joules
(29.80 ft-lb) 57.60 Joules (42.50 ft-lb) 44.60 meters (146.33 ft) 50.80 meters
(166.67 ft) Prepacked Pods Spring Manual and/or Autonomous
650 grams (1.43 lbs) 20 ms 0.57s to 1.30s 6 hours -20°C to +45°C (-4°F to
113°F)*
5.5m² Internal
PSDK PSDK Port
272 grams (0.60 lbs) Carbon Fibre Top Mounted
<2 km (<1.24 mi) 915MHz (North America) / 868MHz (Europe)
*Recommended ambient temperature for operation only. See Battery & Charging and Maintenance and Care sections for more information.
3 Subject to change without warning based on supply chain material availability, payload selection, ongoing testing results, and environmental conditions.
© 2023 AVSS ALL RIGHTS RESERVED
11
PRS-M350 USER MANUAL FOR DJI M350 RTK
3. Payloads
AVSS’s PRS-M350 typically works with the various DJI M350 RTK payload options
that are provided by DJI and that have been developed to integrate through the
DJI PSDK Port. As of 2020-10-01, the following payload combinations, if using
the user manual data located on DJI’s and payload partners’ website4, are
within the 9.0kg Maximum Take-Off Weight criteria. Be aware, due to the
potential unannounced changes by the supporting DJI M350 RTK and payload
manufacturers, these charts are subject to change without any notification.
The user is solely responsible
for verifying the weight inaccuracies and calculating the weight of additional
items attached to the DJI M350 RTK.
Single Payload Configuration Chart
Drone
Battery
DJI M350 RTK
TB60/TB65
Available Weight (MaxTOW 9kg)
H20 0.686 7.908
1.092
Single Payload (KG)
H20T 0.833
8.055
Z30 0.556
7.778
0.945
1.222
XT S 0.387 7.609
1.391
XT2 0.629 7.851
1.149
U10 Methane 0.534 7.756
1.244
Z15 .500 7.722
1.278
Dual Payload Configuration Chart
Drone
Battery
DJI M350 RTK
TB60/TB65
Available Weight (MaxTOW 9kg)
H20T + Z30 1.389
8.611
0.389
Dual Payload (KG)
H20T + XT S 1.220 8.442
0.558
H20T + XT2 1.462
8.684
0.316
H20T + U10 Methane
1.367
8.589
0.411
H20T + Z15 1.333
8.555
0.445
4 Please refer to Appendix A: Drone & Payload References for the complete list of references.
© 2023 AVSS ALL RIGHTS RESERVED
12
PRS-M350 USER MANUAL FOR DJI M350 RTK
Warranty
·
AVSS warrants that the PRS-M350 and its accessories are free from defects and fit for the
operational purpose intended.
·
The warranty period for the PRS-M350 is, the earliest of, twelve (12) months after purchase,
or after three Parachute PodTM deployments, which starts on the date listed as per the user’s
invoice from an Authorized Dealer.
·
This warranty requires the PRS-M350 to be shipped to AVSS’s location for analysis and may
either be fixed, replaced and/or deemed voided of warranty at the sole discretion of AVSS.
·
If the customer believes the PRS-M350 did not properly function or deployed the Parachute
PodTM in a non-failure event (False-Positive), the customer must send AVSS the following files: PRS-M350 Data
DJI M350 RTK DAT data
DJI M350 RTK Text File
·
If the PRS-M350 is deemed void, the cost of analysis and shipping shall be the responsibility
of the end-user. Nothing herein contained shall be construed to exclude or limit any warranty,
express or implied by law.
·
AVSS hereby declares that the warranty shall be deemed void if the PRS-M350 is not used for
the intended operational uses and/or if alterations, tampering, or any actions deemed
comprising by AVSS, directly or indirectly, of the PRS-M350 This includes, but not limited to,
non-standard use, the use of potentially disabling anti-operations technology, and/or
unintended damage by the end-user.
·
The manual triggering device for the parachute is warrantied against any manufacturing
defect.
·
The product warranty does not cover water damage.
·
If the product is used or handled in any way otherwise described within this user manual, the
warranty shall be void.
·
The PRS-M350 purpose is to assist in decreasing the ground impact energy caused by the DJI
M350 RTK mid-flight failure. The end-user cannot in any circumstances from AVSS pursue any
compensation or allowance if their DJI M350 RTK is damaged.
·
It is the responsibility of the purchaser to contact AVSS to obtain additional or updated copies
of the user manual.
© 2023 AVSS ALL RIGHTS RESERVED
13
PRS-M350 USER MANUAL FOR DJI M350 RTK
What’s in the Box:
1. Parts Included
A
B
E C
F D
G
H
A. Parachute PodTM
B. FTS Connector
C. Electronic Module
D. Top Plate
E. Side Brackets (2)
F. Bracket Leg Connectors (2)
I
J
K
L
G. FTS PSDK Module
H. HR30 FTS Cable
I. Manual Trigger Device with Battery
J. Allen Keys
K. USB-C to USB-A Cable
L. M6 Bolt and Washer (2)
© 2023 AVSS ALL RIGHTS RESERVED
14
PRS-M350 USER MANUAL FOR DJI M350 RTK
System Overview
1. Parachute Recovery System
A
F
I
B
D G
J
C
E
H
K
A. Parachute PodTM
B. Electronic Module C. MicroSD Dust Cap for the
USB/microSD Card Slot D. Status LED
E. Power Button
F. Firing Pin Receptacles G. Orientation Key H. Battery Door I. Electrical Contacts J. Continuity LED K. HR30 FTS Connector
© 2023 AVSS ALL RIGHTS RESERVED
15
PRS-M350 USER MANUAL FOR DJI M350 RTK
2. Attachment Bracket
A
B
C
E
D
A. Top Plate B. Quarter Turns (2) C. Side Plates (2) D. Landing Gear Screws
(8) E. Bracket Leg Connectors
© 2023 AVSS ALL RIGHTS RESERVED
16
PRS-M350 USER MANUAL FOR DJI M350 RTK
3. Flight Termination System Through PSDK
A
D
C B
A. FTS PPSDK Module
B. HR30 FTS Cable Female Connector C. USB-C Connector to DJI M350 RTK
PSDK Port
E
D. HR30 FTS Cable to Electronic Module Connector
E. HR30 FTS Cable to FTS Connector
© 2023 AVSS ALL RIGHTS RESERVED
17
PRS-M350 USER MANUAL FOR DJI M350 RTK
4. Manual Triggering Device
A
B
C
D
F E
A. Triggering Button B. Antenna C. Lanyard Attachment D. Belt Clip E. Arm
Button
H G
I
F. Status LED G. Power Button H. Sync Button I. USB-C Charging Port
© 2023 AVSS ALL RIGHTS RESERVED
18
PRS-M350 USER MANUAL FOR DJI M350 RTK
Installation
ENSURE BOTH THE PRS-M350 AND DJI M350 RTK ARE OFF DURING INSTALLATION UNLESS
REQUIRED FOR COMPLETING THE STEP.
1. Electronic Module
Turning on the PRS-M350
Step 1
Turn on To turn on PRS-M350, press on the System ON/OFF switch.
Step 1
Press and Hold Sync
Button
Synchronization on PRS-M350
To synchronize the PRS-M350, ensure the PRS-M350 is OFF. Next, pull the tab on
the microSD dust cap cover to open it. Then, press and hold the small blue
synchronization button in the top corner.
Step 2
Turn On PRS
While holding the button, turn ON the PRS. The Main status LED should turn white after a moment.
Step 3
Turn On Remote
Turn on the manual remote while holding the sync button that is located next to the power button. The LED on the remote will turn white.
Step 4
Syncing
Once both the PRS and remote are on and in the sync mode (white LED), they
will pair. The remote will indicate that the pair is connected and the status
LED on both the PRS and the remote will green. The PRS
and remote are now bound. They can now be turned off.
© 2023 AVSS ALL RIGHTS RESERVED
19
PRS-M350 USER MANUAL FOR DJI M350 RTK
2. Parachute PodTM
· ONLY REMOVE THE PARACHUTE POD IF THE PARACHUTE HAS BEEN DEPLOYED.
· ENSURE THAT THE PRS-M350 IS OFF BEFORE REPLACING THE POD.
Attaching and changing the Parachute PodTM
Remove
Step 1
Parachute PodTM
from PRS-
Using the supplied hex key, unscrew the M6 bolt until the pod can be removed. Do not reuse the bolt and washer when attaching a new Parachute PodTM.
M350
Step 2
Align New Parachute
PodTM
Remove the new Parachute PodTM from its shrink wrap packaging. Align the
Parachute PodTM above the
electronics module such that the electrical contacts
will mate properly (as shown).
Press
Step 3
Parachute PodTM Against
Press the Parachute PodTM against the electronics module. The two shall mesh so that they do not slide against each other.
Module
Step 4
Slide Washer onto M6
Bolt
Take a new M6 bolt and slide on a new washer. The washer is slightly cone shaped. Ensure that the narrow end is towards the head of the bolt.
Step 5
Tighten Bolt
Using the M5 hex key, tighten the bolt.
Step 6
Power On
Place the PRS-M350 on a flat surface and turn on.
Step 7
Check Continuity
Check that the continuity light on the side of the PRSM350 is lit. This indicates that the electrical contacts are properly connected to the pod.
Step 8
Power Off
Power off the module. The new Parachute PodTM is now successfully installed.
© 2023 AVSS ALL RIGHTS RESERVED
20
PRS-M350 USER MANUAL FOR DJI M350 RTK
3. Attachment Bracket
First Time Use
Bracket Leg Connectors for the DJI M350 RTK
Step 1 Step 2
Attachment Bracket Leg Connectors
Screw in Landing Leg Connectors
Unscrew and remove the M350 landing gear. Then, align the landing gear spacers to the bottom of the side brackets. Ensure the flat side of the spacers are attached to the side brackets and that the hollow middle is directed towards the M350 landing gear attachment point. Align the side brackets to the landing leg connectors and attach the landing gear to the outside of the side brackets. Then, screw in the provided landing gear bolts so that, in the following order, the screw is attached to the M350 landing gear, side brackets, spacers, and M350.
THE BRACKET SYSTEM SHALL BE FIRMLY ATTACHED. WHEN THE PARACHUTE DEPLOYS, THE PARACHUTE WILL TRANSFER THE ENTIRE WEIGHT OF THE DJI M350 RTK TO THE ATTACHMENT BRACKET.
© 2023 AVSS ALL RIGHTS RESERVED
21
PRS-M350 USER MANUAL FOR DJI M350 RTK
Ongoing Use
Installing the Attachment Bracket Before Use
Step 1
Spacers Prepared
After completing the first time install steps, the DJI M350 RTK and PRS-M350 are ready to be attached for flight.
Step 2
Rear Side Plate
Alignment
Standing behind the drone, take the rear side plate as shown and ensure that the foam is on the inside, orientated towards the DJI M350 RTK.
Step 3
Rear Side Plate
Insertion
Align the heel of the bracket with the slot in the spacer block.
Step 4
Rear Side Seat the heel into the slot to form a Plates hinge.
© 2023 AVSS ALL RIGHTS RESERVED
22
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 5
Rear Side Plates
Rotate the plate towards the back of the DJI M350 RTK until the hook latches into the block. A click should be felt/heard.
Step 6
Front Side Plates
Take the front side plate and ensure the quarter turn twist tab is facing away from the drone as shown.
Step 7
Front Side Plates
Align the tab at the bottom of the bracket with the slot located at the front of the spacer block.
Step 8
Front Side Plates
Slide the tab into the slot. A click should be felt/heard when it is fully seated.
Step 9
Front Sides The Side Plates are not installed. Plates Repeat steps 1-9 for the other side.
© 2023 AVSS ALL RIGHTS RESERVED
23
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 10
Top Plate
Ensure that both side brackets are fully inserted. The flat surface on which the top plate will rest should be flat.
Step 11
Top Plate
Bend the front side plates outwards as shown.
Step 12
Top Plate
Align the slots in the top plate with the side plate tabs.
Step 13
Top Plate
Ensuring that the front side plates are still pushed out, lower the top plate onto the side plates.
Step 14
Top Plate
The side plate tabs should pass through the slots in the top plate.
© 2023 AVSS ALL RIGHTS RESERVED
24
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 15
Top Plate
Push the top plate towards the back of the drone such that it locks with the hooks on the side plates.
Step 16
Top Plate
Push the front side plate inwards so that it rests against the top plate. Both side plates should be aligned.
Step 17
Top Plate
Once the side plate is pushed in towards the top plate, push the quarter turn in and rotate clockwise to lock.
Step 18
Top Plate
The quarter turn tab should be horizontal once it is locked.
Step 19
Top Plate
Pull outwards on the front side plate to ensure that the quarter turn is secured.
Step 20
Top Plate
The bracket is now installed and ready for flight.
© 2023 AVSS ALL RIGHTS RESERVED
25
PRS-M350 USER MANUAL FOR DJI M350 RTK
4. PSDK Flight Termination System Firmware Configuration Ongoing Use
Connecting PRS-M350 FTS PSDK Module.
Open the DJI Step 1 M350 RTK PSDK Open PSDK port.
Port
Orient the PRS- Align the PRS-M350 FTS PSDK
Step 2 M350 FTS PSDK Module so the HR30 Connector is
Module
pointing up.
Step 3
Align the PRSM350 FTS PSDK
Module
Align the PRS-M350 FTS PSDK Modules USB-C to the DJI M350 RTK PSDK port and is facing the correct orientation with the HR 30 connector closer to the front of the DJI M350 RTK.
Step 4
Connect the PRS-M350 FTS PSDK Module
Gently, but firmly, connect the PRSM350 FTS PSDK with the DJI M350 RTK PSDK port.
Step 5
Plug in the PRSM350 FTS PSDK Module to the DJI M350 RTK
Ensure the PRS-M350 FTS PSDK module is securely plugged in.
Step 6
Connect HR30 FTS Cable to Electronic Module and FTS PSDK Module
Use the HR30 FTS cable to connect the FTS interface on the left side of the PRS-M350 (the side with no cap) and the FTS PSDK Module.
· VERIFY THAT THE PSDK APP HAS BEEN ACTIVATED. · VERIFY THAT ALL HARDWARE CONNECTIONS ARE SECURED.
© 2023 AVSS ALL RIGHTS RESERVED
26
PRS-M350 USER MANUAL FOR DJI M350 RTK
First Time Use & After Firmware Updates The PRS-M350 uses the DJI M350 RTK
Onboard SDK (PSDK) to instigate flight termination. The flight termination
system shuts off the DJI M350 RTK motors prior to the deployment of the
Parachute PodTM. This installation section provides the steps to correctly
configure and activate the DJI M350 RTK PSDK App using DJI Assistant 2
(Enterprise). These steps must be completed prior to first time use, and after
updating the firmware on the DJI M350 RTK.
Step 1
Before Starting
Configure the PSDK in DJI Assistant 2
To complete this configuration using DJI Assistant 2 (Enterprise), an internet
connection is required. Download and install DJI Assistant 2 (Enterprise) if
it is not already installed.
The PRS will need to be installed on the DJI M350 RTK. Please keep the
hardware connection described on page 26. You will also need the manual remote
to verify the status.
Step 2
Plug in USBC Cable
Plug in the USB-C cable to the Assistant Port located on the right side of the drone. Connect the other end of the cable to your computer.
Step 3
Launch DJI Assistant 2
Launch DJI Assistant 2 (Enterprise). Make sure you have the latest version of DJI Assistant 2, which you can download from https://enterprise.dji.com/matrice-350-rtk/downloads
© 2023 AVSS ALL RIGHTS RESERVED
27
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 4
Log in to DJI Assistant 2
Log in to your DJI Account. If you do not have an account, you will need to create one.
© 2023 AVSS ALL RIGHTS RESERVED
28
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 5
Configure Settings
Open the settings tab in the top right of the window. Configure the data authorization settings to allow for data authorization of the Onboard SDK APP ID. Turn on the authorizations as shown.
Step 6
Turn on DJI M350 RTK and PRS
Turn on your DJI M350 RTK. Verify that the PRS is on. It should power on automatically when the DJI M350 RTK is turned on. If it does not turn on automatically, ensure that the FTS Module and FTS Cable are connected properly. The LED on the PRS will blink purple and blue when the FTS is plugged in but not yet configured.
Step 7
Turn on Remote
Turn on the manual trigger remote. This will allow you to verify the status of the FTS.
Step 8
Connect to Drone
Once the drone is on, the DJI Assistant 2 app will recognize that the Matrice 300 RTK is available. Click on the icon to connect to the drone.
© 2023 AVSS ALL RIGHTS RESERVED
29
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 9
Configure DJI M350 RTK PSDK
Select the “Onboard SDK” tab from the left side menu. In this new window, complete the following: · Select “Enable API Control” via checkbox on the top left.
Note: If this is not the first time completing these steps on this drone and you are simply re-configuring the FTS as a result of a firmware update to the DJI M350 RTK, the LED on the PRS may turn green at this stage. In this case, the setup is complete. If this is the first time configuring the FTS on this drone, OR the LED does not turn green, proceed to the next step.
© 2023 AVSS ALL RIGHTS RESERVED
30
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 10
Turn Off PRS and Drone
Turn off the PRS. Once complete, turn off the DJI M350 RTK.
Step 11
Close DJI Assistant 2
Once the PRS and DJI M350 RTK are off, close DJI Assistant.
Step 12
Launch DJI Assistant 2
Re-launch DJI Assistant 2.
Step 13
Turn on Drone and
PRS
Turn on the DJI M350 RTK. Verify that the PRS is on. The PRS should turn on automatically.
© 2023 AVSS ALL RIGHTS RESERVED
31
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 14
Reconnect to Drone in DJI Assistant 2
Once again, the DJI Assistant 2 app will recognize that the DJI M350 RTK is available. Click on the icon to connect to the drone.
Return to the Onboard SDK tab using the left side menu. Verify that the
Step 15
Verify Settings
correct settings were saved. · The “Enable API Control” checkbox on the top left should be checked.
© 2023 AVSS ALL RIGHTS RESERVED
32
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step Cycle PRS Turn the PRS OFF. Wait a moment and then turn the PRS back ON. After a
16
Power moment, the LED will blink purple and blue.
Step 17
Cycle PRS Power Again
Turn the PRS OFF. Wait a moment and then turn the PRS back ON. Now the LED on the PRS should turn green once it has finished initializing. Once the LED is green, the FTS has been properly configured and is ready to use.
The LED will turn yellow if the manual trigger remote is not connected.
Once the LED on the PRS is green, the setup process is complete. Turn off
Step
Process the PRS, drone and manual remote in that order. The USB-C can now be
18
Complete unplugged from DJI assistant. Don’t forget to reinstall the small silicon
cover to protect the Assistant Port during flight.
· MAKE SURE ALL CONNECTORS ARE PROPERLY ATTACHED TO THE FLIGHT TERMINATION
SYSTEM AND PRS-M350.
· DO NOT LEAVE METAL TERMINALS EXPOSED TO OPEN AIR WHEN NOT IN USE.
© 2023 AVSS ALL RIGHTS RESERVED
33
PRS-M350 USER MANUAL FOR DJI M350 RTK
Battery & Charging
1. Battery Safety
· The PRS-M350 EM is equipped with an independent 1S LiPO battery to supply
power. · The PRS-M350 EM and manual triggering device (manual remote) shall be
charged before
use and only by an AVSS supplied or approved USB-C Cable. · The batteries
nominal voltage is 3.7 · Failure to comply may result in damage to the
battery, the PRS-M350, severe overheating,
and/or fire. · If left in unsuitable environments, the system and/or
components may be damaged, the
warranty will shall be void, and the items may not properly function. · During
charging, keep watch on the charging process and react to any potential
problems
that may occur. · Never leave unprotected charging batteries unattended. · The
EM battery should be replaced within two (2) years of purchase.
DO NOT TAKE OFF WHEN THE BATTERY INDICATOR IS RED.
RISK OF EXPLOSION IF THE BATTERY IS REPLACED BY AN INCORRECT TYPE.
2. Battery Charging
Charging
· Only charge the device when it is powered off. · Insert the supplied cable
to the USB-C port on the device. Only use a power source that
follows USB standard for charging. · Maximum ambient temperature for charging
the EM is 40°C (104°F). · Maximum ambient temperature for charging the Manual
Triggering Device (REMOTE) is
35°C (95°F).
Battery Indications
· The battery charge status on both devices (manual triggering device and electronics module) can be checked by pressing the synchronization (“Sync”) button after the startup sequence is finished. The battery colors are the following:
LED Color
(red)
(yellow)
(green)
(white)
Battery %
0-25
25-50
50-75
75-100
THE PRS-M350 EM HAS A BUILT-IN CHARGING CIRCUIT FOR MAINTAINING ADEQUATE BATTERY CHARGE USING POWER SUPPLIED BY THE DJI M350 RTK PSDK PORT.
© 2023 AVSS ALL RIGHTS RESERVED
34
PRS-M350 USER MANUAL FOR DJI M350 RTK
3. Changing Electronic Module Battery
Replacing PRS-M350 Battery
Step 1
Turn the Battery Knobs
Using the knob, turn the knobs to open the battery compartment door.
Step 2
Open Battery Using the knob, turn and open the
Door
battery compartment door.
Step 3
Disconnect battery
connector
Press the release on the battery connector and unplug the cable.
Step 4
Remove Battery
Slowly remove battery from storage compartment.
Step 5
Orient Battery Orient the new battery so that the and Cable cable is as shown in the corner.
Step 6 Step 7
Plug-in Battery
Close Battery Door
Plug-in the battery connector to the cable inside the battery compartment of
the electronic module. Proper attachment will result in a “click” sound and
will be latched.
Once the battery and cable are neatly packed into the compartment, close the
battery door and tighten knob. Ensure that the cable is not being pinched by
the door.
© 2023 AVSS ALL RIGHTS RESERVED
35
PRS-M350 USER MANUAL FOR DJI M350 RTK
Firmware & SD Card
1. MicroSD Card
Removing and/or Inserting the SD Card
Step 1
Open Door
Pull the tab on the charging port cover to open it. The tab will open with a hinged door that opens to the right, towards the power button.
Step 2 Step 3
Remove SD card Insert Micro SD-Card
Gently press the SD card in to release the latch and then pull the card out of
the slot. Use Tweezers if necessary.
To insert the micro SD-card, slide it into the slot with the metal contacts
facing up. An audible click should be heard when it connects properly.
© 2023 AVSS ALL RIGHTS RESERVED
36
PRS-M350 USER MANUAL FOR DJI M350 RTK
2. Firmware Updates
Firmware updates should be performed when a new version is released by AVSS.
Check the AVSS website regularly for firmware updates.
Updating the Firmware
Step 1
Synchronize Remote and PRS-
M350
Follow the steps in Manual Triggering Device Synchronization to synchronize the remote and PRS-M350 before updating the firmware
Step 2 Step 3 Step 4 Step 5 Step 6
Download firmware
Download the firmware from the bottom of the page on https://www.avss.co/products/prsfor-dji-M350-rtk/
Copy the firmware on a SD card
Extract the zip file and copy the firmware (sfb files) on an SD card and insert in the PRS-M350, there may be 3 firmware files if this is a major release (PRSM300, RMT, DBM300). Do not change the file names of the Firmware.
Connect FTS of PRS-M350 to the
DJI M350
Ensure that the drone, PRSM350, and Manual Remote are all turned off. Connect the FTS cable on the PRS-M350 to the DJI M350 RTK.
Turn on DJI M350 RTK drone
Firmware LED
Turn on the drone, which should automatically turn on the PRSM350, if not, turn on the PRSM350 by clicking the main PRSM350 button, next to the status LED. The PRS-M350 LED should turn white to indicate the firmware is downloading. Then the LED should be pink to indicate updating, and then the LED will turn white again to download the next firmware. Wait till the PRS-M350 LED turns yellow, indicating a successful firmware update for the PRS-M350 and daughterboard.
© 2023 AVSS ALL RIGHTS RESERVED
37
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 7
Turn on the manual remote
Keep the remote at least 3 meters away from the DJI M350 RTK, then turn on the remote. The remote firmware will now update and the LED should be white. When the firmware is successfully updated the remote will either restart or turn off. Turn on the remote and the PRS-M350 and remote LED should be green. Check the event log for the correct firmware version listed on the website.
© 2023 AVSS ALL RIGHTS RESERVED
38
PRS-M350 USER MANUAL FOR DJI M350 RTK
Status Indications
The PRS-M350 status, also referenced as “Heartbeat” is indicated using a
combination of LED color and buzzer signals. The PRS-M350 Status LED is
located next to the ON/OFF switch. The LED color on PRSM350 and manual
triggering device indicates the stage of the flight. The manual triggering
device LED indicates its state for 2 seconds and blinks the color of the
PRS-M350 when a connection is established. The buzzers indicate secondary
information which can be either continuous and require action or show a single
event for user information.
1. PRS-M350 Indications
Status
1 Synchronization
2 Updating firmware
3
Initializing
4 FTS not connected
5 FTS diagnostic failed
6
Initialized
LED5 / Buzzer6
W W W W W W W W W W W W W W W W P P P P P P P P P P P B P B P B P B P B
Y Y Y Y Y Y Y Y Y Y P P P P P P P P P P
Required action
Hold Sync and turn on the manual triggering device See firmware section
Connect the HR30 FTS cable to
pass initialization7
Change FTS module or HR30 FTS cable
7
POD not found
Very low battery (~1
8
hour8)
9 Searching for RF
10
Standby
R R R R R R R R R R C C C C C C C C C C OY Y Y YOY Y Y Y G G G G G G G G G G
Install/replace the pod
Replace/charge the battery Turn on the manual triggering device (make sure it
is bound) Ready to take off (No error)
11
ATS Armed
12
ATS Armed
13
Sensor Error
C C C C C C C C C C ATS is active, SD error
G G G G G G G G G G ATS active (No error)
R R R R R R R R R R
Check Event log on the SD card. IMU calibration may be required.
2. Manual Triggering Device Status Indication
The LED on the manual triggering device indicates its status for 2 seconds and
blinks the status of the PRS-M350 so the pilot can monitor the status of the
PRS-M350 in the sky conveniently.
G
G
G
G
G
G
G
G
G
C
5 Purple, Blue, Yellow, Red, Cyan, Green, Off 6 Buzzer is illustrated by lines around the color marks 7 Disconnection of the FTS after the initialization produces the same error and needs a power cycle to run diagnostic again 8 Dependent on environmental factors and number of battery charge cycles
© 2023 AVSS ALL RIGHTS RESERVED
39
PRS-M350 USER MANUAL FOR DJI M350 RTK
The manual triggering device status has the following colors:
Synchronizing
W
Searching
Y
Standby
G
Armed
C
Critical/Triggered
R
3. Manual Triggering Device Synchronization
1. Make sure that both devices are off. 2. Hold the Sync button on the manual
triggering device and, while turning it on, until the LED
turns white. 3. To increase the channel, press and hold the arm button until
the LED turns off then release.
Repeat to increase the channel further. Number of channels depends on the
local regulations. 4. Hold the Sync button on the PRS-M350 and while turning
it on. The LED should be white. 5. Hold the Sync button on the manual
triggering device and turn it on. 6. Both devices will generate a tone and
Sync. 7. Note, the manual triggering device can also change channels. This
feature can be used to
potentially reduce RF interference. To change the manual triggering device
channel, the user should contact customersupport@avss.co.
ONCE A DEVICE IS PUT TO SYNC MODE, IT WILL SYNCHRONIZE WITH THE FIRST DEVICE
IT FINDS. TO PREVENT UNINTENDED SYNCHRONIZATION, SYNCHRONIZE ONLY A SINGLE
PRS-M350 AND A SINGLE MANUAL TRIGGERING DEVICE AT THE SAME TIME.
© 2023 AVSS ALL RIGHTS RESERVED
40
PRS-M350 USER MANUAL FOR DJI M350 RTK
Operating Procedures
1. Hangar Checklist
Make sure manual triggering device battery is fully charged Make sure the
electronic module battery is charged more than 25% Make sure that the memory
card is inserted and has enough storage space
2. Installation Checklist
Ensure that the PRS-M350 and bracket are not damaged Ensure the foam spacers
are still secure to the bracket Insert Attachment Bracket legs, two per side,
to the bracket leg connectors Ensure that the PRS-M350 top plate and main
system are securely attach Verify that bracket is secure to the DJI M350 RTK
Check that the FTS connectors on the electronics module, FTS module and cable
are clean and
undamaged Plugin HR30 FTS cable to FTS module Plug the HR30 FTS cable into the
electronics module Ensure that the HR30 FTS cable is securely connected and
cannot interfere with propellers Check that manual triggering device antenna
is oriented vertically
3. Pre-Flight Checklist
Perform DJI M350 RTK Preflight checks Verify and note any high-power RF
emitters in the operational volume Ensure DJI M350 RTK is in position mode
Connect the HR30 FTS cable with PRS-M350 electronic module Turn on PRS-M350
Manual Triggering Device Turn on PRS-M350 by turning on the DJI M350 RTK Check
continuity light Check the buzzers and lights (heartbeat) Check battery level
and ensure it is at least 50% Wait for successful initialization Ensure no
errors are present Move at least 5 meters away from the DJI M350 RTK Arm the
manual triggering device by holding down the “Arm” button for about 2 seconds
and
will provide audio feedback with the statement of “Remote Armed” Takeoff and
climb to minimum deployable altitude
AUTO-TRIGGER WILL ONLY ARM ONCE AN ALTITUDE OF 43 METERS IS REACHED.
© 2023 AVSS ALL RIGHTS RESERVED
41
PRS-M350 USER MANUAL FOR DJI M350 RTK
4. In-Flight Checklist
Always fly in Position Mode Fly in a safe and controlled manner Avoid flying
over people if unnecessary
5. Landing Checklist
Land DJI M350 RTK gently on a level surface a safe distance from people The
ATS should disarm when the DJI M350 RTK is 5 meters from the ground. The
manual remote
will indicate when the ATS disarms. Do not approach the DJI M350 RTK until the
ATS is disarmed. If the automatic ground detection does not disarm the ATS
then it will take approximately 5 seconds after landing to disarm the ATS.
Note, the pilot will be notified through a voice command on the manual
triggering device Disarm manual triggering device Turn off the PRS-M350 once
it has landed After the PRS-M350 is off, turn off the DJI M350 RTK
6. Post-Flight Checklist (No Deployment)
Ensure PRS-M350 is disarmed before approaching the DJI M350 RTK DO NOT STAND
DIRECTLY OVER THE PRS-M350 WHEN APPROACHING THE DJI M350 RTK Turn off PRS-M350
BEFORE handling the DJI M350 RTK Turn off the DJI M350 RTK Disconnect HR30 FTS
cable before removing batteries Inspect PRS-M350 for damage
7. Deployment Checklist
If necessary, the system can be deployed using the manual triggering device If
possible, fly over a safe area free of people, cars or obstacles Press and
hold the trigger button on the manual triggering device Visually follow the
DJI M350 RTK’s descent to the ground
8. Post-Flight Checklist (With Deployment)
Hold parachute by the lines and fold canopy to prevent wind from inadvertently
inflating the parachute
Turn off PRS-M350 Turn off DJI M350 RTK Disconnect PRS-M350 and bracket from
the DJI M350 RTK Verify that no components are missing
© 2023 AVSS ALL RIGHTS RESERVED
42
PRS-M350 USER MANUAL FOR DJI M350 RTK
Maintenance & Care
Maintenance and inspection intervals of the AVSS PRS-M350 are required to
maximize the safety of each flight and ensure proper functionality for
parachute deployment whenever it may be required. The PRS-M350’s Electronic
Module is expected to reliably function for several parachute deployments so
long as no damage is imparted to the module. The PRS-M350’s Parachute PodTM is
intended as a single-use item that can be quickly removed and replaced in the
field; however, the PRS-M350 must be repacked in 18 month intervals.
1. Post-Flight (Monthly)
1. Visually inspect the PRS-M350 to ensure there is no damage 2. Test the
receptacles on the Electronic Module and Parachute PodTM 3. Test the manual
triggering device
2. Transportation
1. Always transport in a secure storage case
3. Storage
1. Always ensure the power is off 2. Make sure the unit is clean and dry
before putting in the case
4. Extended Storage Considerations
1. Store in a dry room, that is room temperature 2. Uninstall the AVSS
PRS-M350 assembly down to the following separate components:
a. PRS-M350 Electronic Module b. PRS-M350 Parachute Pod 3. Visually inspect
the electrical connectors located on both the Electrical Module and the
Parachute Pod. Check against signs of corrosion, dust/dirt buildup, wear, or
any other types of abnormalities. Clean electrical contacts with rubbing
alcohol and cotton swabs if necessary. 4. Inspect the Main Parachute and
harness lines for: a. Signs of moisture such as standing water or mold b.
Tears, rips, fraying and other signs of wear and damage 5. If any of the above
defects are present during the annual inspection, contact AVSS for further
information.
© 2023 AVSS ALL RIGHTS RESERVED
43
PRS-M350 USER MANUAL FOR DJI M350 RTK
Frequently Asked Questions
1
How do I register my PRS-M350?
Go to https://www.avss.co/products/productregistration/
2
When does the ATS Arm?
43 meters
3
When does the Manual Triggering Device Arm?
By the pilot initializing the manual triggering device through the “arm” button
The ATS disarms when the DJI M350 RTK is within 5
4
When does the PRS-M350 return to a standby state?
meters of the ground. If this sensor is not available then the ATS will disarm
after landing for 5 to 10
seconds and then the user will receive audio
feedback that it has returned to the standby state
5
How many files can the microSD card hold?
Erase microSD card files after 200 flights
6
How do I check the power level on the electronic module?
Push the blue Sync button, located behind the microSD dust cap on the
electronic module, on the
PRS-M350 to check the power level
© 2023 AVSS ALL RIGHTS RESERVED
44
PRS-M350 USER MANUAL FOR DJI M350 RTK
Parachute PodTM Deployment Procedures
The Parachute PodTM must be repacked every 18 months. To return a used and/or
unused Parachute PodTM, an end-user may do so by sending the Parachute PodTM
directly to AVSS or by returning the Parachute PodTM to their Authorized
Dealer.
Sending to AVSS:
· Before sending the Parachute PodTM to AVSS, contact customersupport@avss.co
to request a shipping label.
· If you are purchasing a new Parachute PodTM, AVSS will send you a purchase
link for a replacement Parachute PodTM, plus deposit.
· Once fully paid, AVSS will then send you the replacement Parachute PodTM. ·
To return your Parachute PodTM and receive your deposit, utilize the same box
with the
provided shipping label to send the Parachute PodTM to AVSS. · Once AVSS
receives the Parachute PodTM and completes the visual inspection, you will be
notified and will receive your deposit within fourteen business days.
Sending to an Authorized Dealer:
· Contact your Authorized Dealer to notify them that you will be returning
and/or requesting a new Parachute PodTM
· If you are purchasing a new Parachute PodTM, the Authorized Dealer will
either send you a purchase link for a replacement Parachute PodTM, plus
deposit, or accept payment at their physical location.
· Once fully paid and your Parachute PodTM has been returned, the Authorized
Dealer will then send you or directly provide you with the replacement
Parachute PodTM.
© 2023 AVSS ALL RIGHTS RESERVED
45
PRS-M350 USER MANUAL FOR DJI M350 RTK
Customer Support
Email: Telephone:
customersupport@avss.co Monday to Friday, excluding holidays 10:00 am Est to 4:00 pm Est +1-844-852-0665
© 2023 AVSS ALL RIGHTS RESERVED
46
Appendix A: DJI M350 RTK & Payload References
Drone / Payload
Date
Link
DJI M350 RTK
2023-10-04 https://enterprise.dji.com/matrice-350-rtk/downloads
DJI H20
2020-09-01 https://www.dji.com/ca/zenmuse-h20-series/specs
DJI H20T U10 Methane Wingsland Z15 Zenmuse XT Zenmuse XT 2 Zenmuse Z30
2020-09-01 2019-10-09 2019-09-16 2016-07-11 2018-05-11 2018-10-08
https://www.dji.com/ca/zenmuse-h20-series/specs
https://terra-
1g.djicdn.com/851d20f7b9f64838a34cd02351370894/others/ENa5_U10%20Gas%20Detector_en_format_191009.pdf
https://terra-1g.djicdn.com/851d20f7b9f64838a34cd02351370894/others/Z15_Spot
light_en.pdf
https://dl.djicdn.com/downloads/zenmuse_xt/en/Zenmuse_XT_User_
Manual_V1.2_en0708.pdf
https://dl.djicdn.com/downloads/Zenmuse%20XT%202/Zenmuse%20
XT%202%20User%20Manual%20v1.0.pdf
https://dl.djicdn.com/downloads/zenmuse_z30/20180810/Z30_User_ Manual_EN.pdf
© 2023 AVSS ALL RIGHTS RESERVED
47
PRS-M350 USER MANUAL FOR DJI M350 RTK
Appendix B: IMU Calibration Instructions
A red flashing LED and a beeping sound coming from the PRS-M350 indicates that
the IMU must be calibrated. There are two methods of calibrating the IMU on
the PRS-M350, either by placing the PRSM350 in the travel box or keeping the
PRS-M350 on the drone. The preferred method is in the box; however, if the box
cannot be located, performing the calibration on the drone is acceptable.
PRS-M350 IMU Calibration in the box
Step 1
Remove the PRS-M350 from the brackets on the drone, but do not remove the module from the base plate.
Step 2
Turn the PRS-M350 on and lay it on the PRS box, keeping it stationary for a couple of seconds until the LED flashes red and the PRS-M350 starts beeping.
Step 3
Place the PRS-M350 in its position in the PRS-M350 box.
© 2023 AVSS ALL RIGHTS RESERVED
48
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 4 Close the box.
Step 5
Rotate the box 90 degrees towards the latched end and allow the box to stand on this end for 5 seconds.
Step 6
Rotate the box 90 degrees in the opposite direction and allow it to stand on this end for 5 seconds.
© 2023 AVSS ALL RIGHTS RESERVED
49
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 7
Bring the box back to the original position and rotate it to the right side 90 degrees and wait for 5 seconds.
Step 8
Bring the box back to the original position and rotate it to the left side 90 degrees and wait for 5 seconds.
Step 9
Bring the box back to the original position and leave it stationary for 20 seconds.
Step 10
If the calibration is successful three beeps If the calibration is unsuccessful the LED
will start from the PRS-M350 and the PRS will continue to flash and the beeping will
will auto shutdown in 5 seconds.
sound, go back to step 2 and re-calibrate.
If the calibration is successful, the PRS LED will flash pink and blue, and
the module is ready to fly.
If the travel box cannot be found and calibration is needed, then use the
following method on the drone.
© 2023 AVSS ALL RIGHTS RESERVED
50
PRS-M350 USER MANUAL FOR DJI M350 RTK
PRS-M350 IMU Calibration on the Drone
Step 1
Remove the props from the drone and keep it on a level surface.
Step 2
Turn on the PRS-M350. The PRS-M350 should be beeping and flashing red
Step 3
Tilt the drone backward 90 degrees. Hold steady for 5 seconds.
© 2023 AVSS ALL RIGHTS RESERVED
51
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 4
Bring the drone back to level and then tilt it forward 90 degrees. Hold steady for 5 seconds.
Step 5
Bring the drone back to level and then tilt it towards the right 90 degrees. Hold steady for 5 seconds.
Step 6
Bring the drone back to level and then tilt it towards the opposite side 90 degrees. Hold steady for 5 seconds.
© 2023 AVSS ALL RIGHTS RESERVED
52
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 7
Bring the drone back to level and leave it for 20 seconds.
Step 10
If the calibration is successful three beeps will start from the PRS-M350 and the PRS-M350 will auto shutdown in 5 seconds.
If the calibration is unsuccessful the LED will continue to flash and the beeping will sound, go back to step 2 and re-calibrate.
© 2023 AVSS ALL RIGHTS RESERVED
53
PRS-M350 USER MANUAL FOR DJI M350 RTK
Appendix C: Additional Information
1. Pre-Flight FTS Check
The PRS-M350 allows for a pre-flight FTS check on the ground for the DJI M350 RTK. This pre-flight check is only enabled on the ground with the motors initially disarmed. This PRS-M350 mode is only enabled for 1 minute, after which the PRS-M350 will auto shutdown and must be restarted.
FTS Pre-flight testing on PRS-M350
Step 1
Turn On the DJI remote and M350
RTK
Connect the FTS module to the drone and the PRS-M350 and turn on the drone remote controller and then the drone.
Step 2 Step 3
Turn on Remote
Turn on the manual remote by holding the power button. The LED on the top of the remote should turn GREEN.
FTS mode
Hold down the sync button and press the arm button at least 3 times quickly. Keep the sync button held. The LED on the remote and PRS should now be blue. The remote should say “FTS” repeatedly. The PRS-M350 and remote are now in “FTS mode”.
Step 4
Turn Drone motors on
Stay clear of the propellers of the drone and, when safe to do so, start the drone’s motors.
Step 5
FTS Test
To trigger the FTS press the ARM button on the Manual Remote once.
Step 6
Automatic shutdown
After the motors have stopped, the PRS-M350 will automatically shut down, and the Manual Remote will reset. The parachute cannot deploy on the ground and the Red button on the Manual Remote will not be functional in FTS mode.
© 2023 AVSS ALL RIGHTS RESERVED
54
PRS-M350 USER MANUAL FOR DJI M350 RTK
Step 7
Back to Normal Operation
After the FTS test, power off the drone and turn it back on. Ensure that both the manual remote and PRS-M350 have a GREEN LED.
Step 8
Arm the Manual Remote
Arm the Manual Remote and the PRS-M350 is now ready to fly.
The PRS-M350 will automatically shut down after 1 minute if the FTS is not triggered in FTS-mode. If the PRS-M350 is manually restarted before the FTS is triggered or before the timeout then the remote may still be in FTS mode. The remote will also reset after 1 minute of being in FTS mode. This is to prevent any flights in this mode.
2. Ground Risk Buffer Prescription
The table below provides a method to calculate the ground risk buffer zone for your operation according to the Specific Operation Risk Assessment. The rows that are not highlighted are values that are specific to the operation. The DJI M350 RTK max speed in N-Mode is 15 m/s, the wind speed is based on the time and place of the operation. The max altitude is based on the operation. The descent rate should be based off the maximum takeoff weight which is 3.54 m/s.
Ground Risk Buffer T human latency + system latency V1 Drone Max Speed W Wind Speed A Max altitude DR Descent Rate D1 TV1 D2 1.1W*A/DR GRB Ground Risk Buffer = D1 + D2
3s 15 m/s
3 m/s 120 m 3.54 m/s
45 m 111.9 m 156.9 m
© 2023 AVSS ALL RIGHTS RESERVED
55
PRS-M350 USER MANUAL FOR DJI M350 RTK
3. Firmware Update Process for Conversion From PRS-M300 to PRS-M350
To update the PRS-M350 or to make the PRS-M300 compatible with the DJI M350
RTK follow these steps:
1. Update the DJI M350 RTK to the latest version on DJI Assistant 2 2. Enable
the API Control in DJI Assistant 2 under “Onboard SDK” as shown in Section 4.
Of the
PRS-M350 User Manual 3. Download the latest PRS-M350 firmware file from the
AVSS website, as well as the latest PSDK
firmware file (DBM300) and add extract these “sfb” files. Copy them to the SD
card of the PRSM350 and place the SD card back in the PRS-M350. 4. Connect the
PRS-M350 to the DJI M350 RTK. The connector should be on the side of the
PRSM350 that does NOT have a dust cap. 5. Turn on the DJI M350 RTK and the
PRS-M350 should automatically turn on. If it does not, then ensure that the
black PSDK module is connected to the DJI M350 RTK. You may have to press down
with some pressure on the PSDK module to ensure it is connected. 6. Once the
PRS-M350 is turned on the main LED will turn white indicating that the
firmware is updating. If it does not turn white, then you may have the wrong
firmware frequency (915 vs 868) or the PRS-M350 may not be installed in a
steady and level manner. 7. After updating the LED will flash pink and blue
for around 2 minutes. After 2 minutes the drone and PRS-M350 should establish
a connection and the LED will be either yellow (if the manual remote is turned
off) or green.
© 2023 AVSS ALL RIGHTS RESERVED
56
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>